Back MARINE RADAR/ARPA FAR-28x7 Series FAR-21x7(-BB) Series www.furuno.co.
The paper used in this manual is elemental chlorine free. ・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN Telephone : +81-(0)798-65-2111 Fax : +81-(0)798-65-4200 All rights reserved. Printed in Japan A : JAN . 2004 G2 : OCT . 31, 2007 Pub. No. OME-35190-G2 (DAMI ) FAR-2107/2807 SER.
IMPORTANT NOTICES • This manual is intended for use by native speakers of English. • No part of this manual may be copied or reproduced without written permission. • If this manual is lost or worn, contact your dealer about replacement. • The contents of this manual and equipment specifications are subject to change without notice. • The example screens (or illustrations) shown in this manual may not match the screens you see on your display.
SAFETY INSTRUCTIONS WARNING Radio Frequency Radiation Hazard The radar antenna emits electromagnetic radio frequency (RF) energy which can be harmful, particularly to your eyes. Never look directly into the antenna aperture from a close distance while the radar is in operation or expose yourself to the transmitting antenna at a close distance. Distances at which RF radiation levels of 100 and 10 W/m2 exist are given in the table below.
SAFETY INSTRUCTIONS WARNING ELECTRICAL SHOCK HAZARD WARNING Use the proper fuse. Do not open the equipment. Only qualified personnel should work inside the equipment. Turn off the radar power switch before servicing the antenna unit. Post a warning sign near the switch indicating it should not be turned on while the antenna unit is being serviced. Prevent the potential risk of being struck by the rotating antenna and exposure to RF radiation hazard.
SAFETY INSTRUCTIONS CAUTION WARNING No one navigational aid should be relied upon for the safety of vessel and crew. The navigator has the responsibility to check all aids available to confirm position. Electronic aids are not a substitute for basic navigational principles and common sense. • This ARP automatically tracks automatically or manually acquired radar targets and calculates their courses and speeds, indicating them by vectors.
TABLE OF CONTENTS TABLE OF CONTENTS FOREWORD ........................................................................................................ xi PROGRAM NUMBER ........................................................................................ xiv SYSTEM CONFIGURATION............................................................................... xv SPECIFICATIONS........................................................................................... SP-1 1. RADAR OPERATION..................
SAFETY INSTRUCTIONS 1.21 Measuring the Bearing .............................................................................................1-33 1.21.1 Measuring the bearing ...................................................................................1-33 1.21.2 Choosing true or relative bearing ...................................................................1-35 1.22 Collision Assessment by Offset EBL.........................................................................1-36 1.22.
TABLE OF CONTENTS 1.36 1.37 1.38 1.39 1.40 1.41 1.42 1.43 1.44 1.45 1.46 1.47 1.48 1.49 1.50 1.51 1.52 Noise Rejector ......................................................................................................... 1-70 Suppressing Second-trace Echoes.......................................................................... 1-71 Adjusting Brilliance of Screen Data.......................................................................... 1-72 Watch Alarm .......................................
SAFETY INSTRUCTIONS 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 3.18 3.6.1 Setting manual acquisition conditions ............................................................. 3-7 3.6.2 Manually acquiring a target ............................................................................. 3-7 ARP Symbols and ARP Symbol Attributes................................................................. 3-9 3.7.1 ARP symbols ...........................................................................
TABLE OF CONTENTS 4.7.2 Detailed target data ......................................................................................... 4-9 4.8 AIS Symbol Attributes .............................................................................................. 4-10 4.8.1 AIS symbol brilliance ..................................................................................... 4-10 4.8.2 AIS symbol size and color ............................................................................. 4-11 4.
SAFETY INSTRUCTIONS 5.13 5.14 5.15 5.16 5.12.3 Erasing waypoints..........................................................................................5-24 5.12.4 Waypoint list ..................................................................................................5-25 5.12.5 Displaying waypoint name and number..........................................................5-26 Nav Lines ..............................................................................................................
FOREWORD A Word to the Owner of the FAR-28x7/FAR-21x7(-BB) Congratulations on your choice of the FURUNO FAR-28x7/FAR-21x7(-BB) Series Radar. We are confident you will see why FURUNO has become synonymous with quality and reliability. For over 50 years FURUNO Electric Company has enjoyed an enviable reputation for innovative and dependable marine electronics equipment. This dedication to excellence is furthered by our extensive global network of agents and dealers.
FOREWORD • Two types of trackball-equipped control units are available: RCU-014 (full keyboard) and the RCU-015 (palm control). The trackball is easy to use thanks to the ergonomically designed palm rest. • Simplified operation with point-and-click menu operation. • All functions are accessible by using the trackball alone. • Applicable to HSC (High Speed Craft) • ARPA (Automatic Radar Plotting Aid) or ATA (Automatic Tracking Aid) + AIS, Radar Plotter and Interswitch supplied as standard.
FOREWORD Radar Type and Function Availability This radar series is available in five specification types to meet the requirements of Authorities, and function availability depends on specification type. The table below shows those functions which have limited availability. This manual provides descriptions for all functions in this radar series, and we have endeavored to denote in the text those functions which have limited availability.
PROGRAM NUMBER PC Board Program No. Version No. MAIN 035-9204 02.** (Merchant) / 50.** (Fishing) RFC 035-9202 01.** KEY(REMOTE) 035-9203 01.** ARPA 035-9212 01.
SYSTEM CONFIGURATION See page xvi for detailed information about antenna units and radiators. With FURUNO-supplied monitor FAR-2137S/2167DS/2837S/2837SW * Neither FAR-2157 nor FAR-2167DS carry a performance monitor.
SYSTEM CONFIGURATION Antenna unit FAR-2117, FAR-2117-BB, FAR-2127, FAR-2127-BB, FAR-2827 RSB-096 (24 rpm) RSB-097 (42 rpm) FAR-2137S, FAR-2137S-BB RSB-098/099 (21/26 rpm, 200 VAC, 3ø, 50 Hz; 220 VAC, 3ø, 60 Hz; 380 VAC, 3ø, 50 Hz, 440 VAC, 3ø, 60 Hz) RSB-100/101/102 (45 rpm, 220 VAC, 3ø, 50/60 Hz(HSC); 440 VAC, 3ø, /60 Hz(HSC)) FAR-2157, FAR-2157-BB RSB-106 (18/22 rpm, 200 VAC, 3ø, 50 Hz; 220 VAC, 3ø, 60 Hz) RSB-107 (22 rpm, 24 VDC) FAR-2167DS, FAR-2167DS-BB RSB-111 (21/26 rpm, 200 VAC, 3ø, 50 Hz; 2
SYSTEM CONFIGURATION Blackbox type FAR-2137S-BB/FR-2167DS-BB FAR-2117-BB/2127-BB/FAR-2157-BB ANTENNA UNIT (Performance Monitor PM-51 built in FAR-2137S-BB) * Neither FAR-2157-BB nor FAR-2167DS-BB carry a performance monitor.
SYSTEM CONFIGURATION Console type RCN-001/RCN-002 FAR-2137S/2837S/2837SW FAR-2117/2127/2817/2827/2827W ANTENNA UNIT (Performance Monitor PM-51 built in) ANTENNA UNIT (Performance Monitor PM-31 built in) Waveguide (For FAR-2827W) Waveguide or Coax cable (For FAR-2837SW) TRANSCEIVER UNIT RTR-081 For FAR-2827W TRANSCEIVER UNIT RTR-082 For FAR-2837SW CONSOLE RCN-001/002 Alarm VDR POWER SUPPLY UNIT PSU-007 For FAR-2137S/2837S OR POWER SUPPLY UNIT PSU-011* (For FAR-2827W/2837SW) External Monitor IEC
SYSTEM CONFIGURATION Console type RCN-003/RCN-004 FAR-2117/2127/2817/2827/2827W FAR-2137S/2837S/2837SW ANTENNA UNIT (Performance Monitor PM-51 built in) ANTENNA UNIT (Performance Monitor PM-31 built in) Waveguide (For FAR-2827W) Waveguide or Coax cable (For FAR-2837SW) TRANSCEIVER UNIT RTR-081 For FAR-2827W TRANSCEIVER UNIT RTR-082 For FAR-2837SW CONSOLE RCN-003/004 POWER SUPPLY UNIT PSU-007 For FAR-2137S/2837S OR POWER SUPPLY UNIT PSU-011* (For FAR-2827W/2837SW) * Russian flag only Alarm VDR Ext
SYSTEM CONFIGURATION (This page intentionally left blank.
FURUNO FAR-21x7(-BB)/28x7 SERIES SPECIFICATIONS OF MARINE RADAR/ARPA FAR-21x7(-BB)/28x7 SERIES 1. ANTENNA RADIATORS 1. Type Slotted waveguide array 2. Beam width and sidelobe attenuation Radiator type Length Beam width(H) Beam width(V) Sidelobe within ±10° Sidelobe outside ±10° XN4A 8 ft 0.95° 20° -28 db -32 db XN5A 10 ft 0.75° 20° -26 db -30 db X-band XN12AF XN20AF 4 ft 6.5 ft 1.8° 1.23° 20° 20° -24 db -28db -30 db -32 db XN24AF 8 ft 0.95° 20° -28 db -32 db S-band SN30AF SN36AF 10 ft 12 ft 2.3° 1.
FURUNO 6. Duplexer FAR-21x7(-BB)/28x7 SERIES Ferrite circulator with diode limiter for FAR-2117/2117-BB/2127/2127-BB/2137S/2137S-BB/2157/2157-BB/ 2167DS/2167DS-BB/2817/2827/2827W/2837S Ferrite circulator with TR limiter for FAR-2837SW 3. DISPLAY UNIT 1. Screen Yellow or green echoes in 32 levels. Rasterscan non-interlace at 64 kHz horizontal, 60 Hz vertical. Non-IMO type has yellow or green monochrome plus 3-color display according to echo strengths. FAR-21x7 series FAR-28x7 series Size, model 20.
FURUNO FAR-21x7(-BB)/28x7 SERIES PM-51 (S-band) 1. Frequency range 3020 to 3080 MHz 2. Input power Min. -5 dBm, Max. +15 dBm nd -15 dBm 3. Power output (2 pulse max output) nd 4. Power output (2 pulse min output) -35 dBm 5. Steps levels (1st pulse to 2nd pulse) 9.0 to 11.0 dB 6. POWER SUPPLY 1. Display unit 24 VDC or 115/230 VAC, 1ø, 50/60 Hz FAR-21x7: 24 VDC, 2.3 A; 100-230 VAC, 0.7A (100 V) FAR-28x7: 24 VDC, 3.2 A; 100-230 VAC, 0.
FURUNO FAR-21x7(-BB)/28x7 SERIES 8. OPTIONAL EQUIPMENT SWITCHING HUB HUB-100 1. Access Format CSMA/CD 2. Switching Format Store and Forward 3. Transmission Speed Half-duplex: 10Mbps/100Mbps Full-duplex: 20Mbps/200Mbps 4. Necessary Cabling 10BASE-T: Category 3 or higher STP cable 100 BASE-TX: Category 5 or higher STP cable 5. Max. Cable Length 100 m 6. Ports 7.
1. RADAR OPERATION 1.1 Turning on the Power The [POWER] switch ( ) is located at the left corner of the control unit. Open the POWER switch cover and press the switch to turn on the radar system. To turn off the radar, press the switch again. The screen shows the bearing scale and digital timer approximately 30 seconds after power-on. The timer counts down three minutes of warm-up time. During this period the magnetron (transmitter tube) is warmed for transmission.
1. RADAR OPERATION The radar is initially set to previously used range and pulse length. Other settings such as brilliance levels, VRMs, EBLs and menu option selections are also set to previous settings. The [STBY/TX] key (or TX STBY box) toggles the radar between STBY and TRANSMIT status. The antenna stops in stand-by and rotates in transmit. The magnetron ages with time resulting in a reduction of output power.
1. RADAR OPERATION Control Unit Two types of control units are available: Control Unit RCU-014 (full keyboard) and Control Unit RCU-105 (palm control).
1. RADAR OPERATION Control description Control Description Control Unit RCU-014 (full keyboard) POWER Turns the system on and off. EBL and VRM rotary controls Adjust EBL and VRM, respectively. EBL ON, EBL OFF Turns the EBLs on and off, respectively. F1-F4 Execute menu short cut assigned. ALARM ACK Silences audible alarm. STBY TX Toggles between stand-by and transmit. BRILL Adjusts display brilliance. A/C RAIN Suppresses rain clutter. A/C SEA Suppresses sea clutter.
1. RADAR OPERATION 1.4 Main Menu You may access the MAIN menu from the full keyboard or by using the trackball. In later sections only the procedure for menu operation by trackball is given. Main menu operation by keyboard 1. Press the [MENU] key. The MAIN menu appears in the text area at the right side of the screen. [MAIN MENU] 1 2 3 4 5 6 7 8 9 [ECHO] [MARK] [ALARM] [ARP l AIS] [PLOTTER] [CARD] [NAV DATA] [NAV LINE z WPT] [CUSTOMIZE z TEST] Echo processing functions Mainly turns markers on/off.
1. RADAR OPERATION Main menu operation by trackball 1. Roll the trackball to choose the MENU box at the right side of the screen. The guidance box at the bottom right corner (see the illustration at the bottom of the next page for location) now reads “DISP MAIN MENU.” MENU Menu box 2. Push the left button to display the MAIN menu.
1. RADAR OPERATION 1.5 Operation Using the On-Screen Boxes All radar functions can be accessed by using the trackball alone. This is done by choosing the appropriate on-screen box with the trackball and operating the trackball module to choose item and option. (See paragraph 1.9 for location of all on-screen boxes.) On-screen boxes come in two varieties: Function selection and function selection w/pop-up menu.
1. RADAR OPERATION Trackball marker location and guidance box indication The trackball marker is either a cursor (+) or an arrow ( ) depending on whether it is within or outside the display area, respectively. Further, the indication in the guidance box changes according to trackball marker location. Guidance box reads "JUMP CURSOR / DISP MENU." Push the left button to choose the on-screen box closest to the arrow or push the right button to display the MAIN menu.
1. RADAR OPERATION 3. The pop-up menu attached to the MARK box is the MARK menu. To open the menu, push the right button. The menu opens in the text area at the right side of the screen. [MARK MENU] 1 ORIGIN MARK STAB GND/SEA 2 MARK KIND ORIGIN MARK(No. )/ ORIGIN MARK(SYM)/ MAP MARK/ WP 1~50/ WP 51~ 100/ WP 101~150/ WP 151~ 200/ OWN SHIP SHAPE 8 MARK POSN CURSOR/OS/L/L 00°000.00 N 000°000.
1. RADAR OPERATION 1.6 Cursor Menu Functions which require the use of the cursor, such as EBL offset and zoom, may be activated directly from the guidance box or from the CURSOR menu, either method with the cursor inside the effective display area. Below is the procedure for choosing a cursor-related function from the CURSOR menu. In later sections only the procedure for selection from the guidance box is given.
1. RADAR OPERATION 6. The guidance box shows “XX / EXIT.” (XX = function chosen). Roll the trackball to place the cursor where desired. 7. Push the left button to execute the function selected at step 5. 8. To quit the function selected, push the right button when the guidance box shows “XX / EXIT.” (XX = function chosen at step 5) 1.7 Monitor Brilliance The brilliance of the entire screen should be adjusted according to lighting conditions.
1. RADAR OPERATION 1.8 Choosing the Display Mode This radar has two display modes: Radar and Radar + Plotter. Choose a display mode as below. Note that a display mode cannot be chosen when the menu is open. 1. Roll the trackball to place the arrow in the DISPLAY MODE box at the top of the screen. DISPLAY XX* * XX = display mode (RADAR, +PLOTTER) DISPLAY MODE box 2. Push the left button to choose appropriate mode: RADAR: Radar picture +PLOTTER: Radar picture + plotter picture (incl.
1. RADAR OPERATION 1.9 On-Screen Boxes and Markers Reference Point Box Trial Maneuver (Elapsed time shown when trial maneuver is active.
1. RADAR OPERATION HDG SPD SB COG SOG 9.9kt BT WT MAN 0.1kt 30.2°T 10.2.2kt GPS OS POSN Electronic Position-fixing System and position* Depth Depth Echogram (See 1.40.) Zoom display appears in nav data box when nav data is turned off. Heading is TRUE (variation-corrected gyro or magnetic heading) Speed data is LOG, MAN, etc., showing sensor and types. CSE when water tracking mode is selected. STW when water tracking mode is selected. 242.2°T DGPS 34°40.00N 135°24.00E DEPTH 22.
1. RADAR OPERATION 1.10 Tuning the Receiver 1.10.1 Choosing the tuning method The tuning method can be selected with the TUNE box at the top of the screen. 1. Roll the trackball to choose the TUNE box (TUNE AUTO or TUNE MAN) at the top of the screen. Tuning bar Place arrow inside box to adjust tuning, when TUNE MANU is selected. Tuning method (AUTO or MANU) TUNE AUTO Tuning level TUNE box 2. Push the left button or roll the wheel to display TUNE AUTO or TUNE MAN as appropriate. 3.
1. RADAR OPERATION 1.10.3 Automatic tuning Choose automatic tuning following paragraph 1.10.1. The TUNE box shows TUNE AUTO. 1.10.4 Manual tuning 1. Roll the trackball to choose the RANGE box at top left corner and then push the left or right button as appropriate to choose the 48-mile range. Push the left button to lower the range; the right button to raise the range. 2. Choose manual tuning following the procedure in paragraph 1.10.1. 3.
1. RADAR OPERATION 1.12 Presentation Modes This radar has the following presentation modes: Relative Motion (RM) Head-up: Unstabilized Head-up TB: Head-up with compass-stabilized bearing scale (True Bearing) where the bearing scale rotates with the compass reading. Course-up: Compass-stabilized relative to ship’s orientation at the time of selecting course-up. North-up: Compass-stabilized with reference to north Stern-up: The radar image is rotated 180°.
1. RADAR OPERATION 1.12.2 Description of presentation modes Head-up mode The head-up mode is a display in which the line connecting own ship and the top of the display indicates own ship’s heading. The target pips are painted at their measured distances and in their directions relative to own ship’s heading. A short line on the bearing scale is the north marker indicating heading sensor north. A failure of the heading sensor input will cause the north marker to disappear and the readout to show ***.
1. RADAR OPERATION Head-up TB (True Bearing) mode Radar echoes are shown in the same way as in the head-up mode. The difference from normal head-up presentation lies in the orientation of the bearing scale. The bearing scale is heading sensor stabilized. That is, it rotates in accordance with the heading sensor signal, enabling you to know own ship’s heading at a glance. This mode is available when the radar is interfaced with a gyro heading sensor.
1. RADAR OPERATION True motion mode Own ship and other moving objects move in accordance with their true courses and speed. In ground stabilized TM, all fixed targets, such as landmasses, appear as stationary echoes. In the sea stabilized TM without set and drift inputs, the landmass can move on the screen. Note that true motion is not available on the 72 nm (non-IMO type only) or 96 nm range scale.
1. RADAR OPERATION 1.13 Entering Own Ship's Speed The ARP and azimuth stabilized presentation modes require own ship speed input and compass signal. The speed can be entered from a log (STW) or GPS (SOG) or manually on the menu. Note that FURUNO GPS Navigator GP-90 provides COG and SOG. 1.13.1 Automatic speed input by log or GPS navigator 1. Roll the trackball to place the arrow in the SPD box at the top right corner of the screen. 2. Push the right button to display the SPEED menu.
1. RADAR OPERATION 1.13.2 Manual speed input If the speed log is not working, enter speed manually as below. In this case the speed data type is shown as MANUAL and is speed thru water (STW). Note that, for the IMO specification radar, manual speed input is not available when the AIS feature is active. 1. Roll the trackball to place the arrow in the SPD box at the top right corner of the screen. 2. Push the right button to display the SPEED menu. 3.
1. RADAR OPERATION 1.15 Choosing the Pulselength The pulselength in use is displayed at the upper-left position of the screen using the indications shown in the table below. Label and pulselength Indication Pulselength (μs) S1 (Short pulse 1) 0.07 S2 (Short pulse 2) 0.15 M1 (Medium pulse 1) 0.3 M2 (Medium pulse 2) 0.5 M3 (Medium pulse 3) 0.7 L (Long pulse) 1.2 *: S, M1, M2 and L on FAR-2157(-BB) and S-band radars. Appropriate pulselengths are preset to individual range scales and function keys.
1. RADAR OPERATION 3. Roll the wheel to choose 8 [PULSE] and then push the wheel. [PULSE MENU] [PULSE MENU] 1 BACK 2 0.5NM S1/S2 3 0.75NM S1/S2/M1 4 1.5NM S1/S2/M1 5 3NM S2/M1/M2/M3 6 6NM M1/M2/M3/L 7 12-24NM M2/M3/L 1 BACK 2 0.75NM S/M1 3 1.5NM S/M1 4 3NM M1/M2 5 6NM M2/L 6 12-24NM M2/L PULSE menu PULSE menu (12, 25 kW X-band) (50 kW X-band, all S-band) 4. Roll the wheel to choose a range and then push the wheel or the left button. 5.
1. RADAR OPERATION 1.16 Adjusting the Sensitivity The gain control adjusts the sensitivity of the receiver. The proper setting is such that the background noise is just visible on the screen. If you set up for too little sensitivity, weak echoes may be missed. On the other hand excessive sensitivity yields too much background noise; strong targets may be missed because of the poor contrast between desired echoes and the background noise on the display.
1. RADAR OPERATION 1.17 Suppressing Sea Clutter Echoes from waves cover the central part of the display with random signals known as sea clutter. The higher the waves, and the higher the antenna above the water, the further the clutter will extend. When sea clutter masks the picture, suppress it by the A/C SEA control, either manually or automatically. 1.17.1 Choosing method of adjustment 1. Roll the trackball to choose SEA AUTO or SEA MAN (whichever is shown) at the top of the display.
1. RADAR OPERATION By trackball 1. Choose SEA AUTO following the procedure in paragraph 1.17.1. 2. Roll the trackball to place the arrow in the A/C SEA level indicator at the top of the display. 3. While observing the A/C SEA level indicator, roll the wheel downward to increase the A/C SEA or upward to decrease it. 100 levels (0-100) are available. 1.17.
1. RADAR OPERATION 1.18 Suppressing Rain Clutter Use the AUTO RAIN and A/C RAIN to suppress rain clutter. AUTO RAIN suppresses rain clutter in the picture and A/C RAIN suppresses clutter picked up by the antenna. 1.18.1 Turning AUTO RAIN on or off 1. Roll the trackball to choose the PICTURE box at the left side of the screen. 2. Push the right button to show the PICTURE menu.
1. RADAR OPERATION 1.18.2 Adjusting A/C RAIN The vertical beam width of the antenna is designed to see surface targets even when the ship is rolling. However, by this design the unit will also detect rain clutter (rain, snow, or hail) in the same manner as normal targets. The A/C RAIN control adjusts the receiver sensitivity as the A/C SEA control does but rather in a longer time period (longer range). The higher the setting the greater the anti-clutter effect.
1. RADAR OPERATION 1.19 Interference Rejector Mutual radar interference may occur in the vicinity of another shipborne radar operating in the same frequency band. It is seen on the screen as a number of bright spikes either in irregular patterns or in the form of usually curved spoke-like dotted lines extending from the center to the edge of the picture. Activating the interference rejector circuit can reduce this type of interference. The interference rejector is a kind of signal correlation circuit.
1. RADAR OPERATION 1.20 Measuring the Range The range to a target may be measured three ways: with the fixed range rings, with the cursor, or with the VRM. Use the fixed range rings to obtain a rough estimate of the range to a target. They are the concentric solid circles about own ship, or the sweep origin. The number of rings is automatically determined by the selected range scale and their interval is displayed at the upper-left position of the screen.
1. RADAR OPERATION 1.20.2 Measuring range by the variable range marker (VRM) There are two VRMs, No. 1 and No. 2, which appear as dashed rings so that you can discriminate them from the fixed range rings. The two VRMs can be distinguished from each other by different lengths of dashes. No. 1 VRM 330 340 350 000 010 020 030 320 Target blip 040 310 050 060 300 070 290 280 080 270 090 260 100 250 110 240 120 230 No.
1. RADAR OPERATION 1.20.3 Choosing VRM unit of measurement (B, C and W types) 1. Roll the trackball to choose the MENU box at the right side of the screen. The guidance box at the bottom right corner now reads “DISP MAIN MENU.” 2. Push the left button to display the MAIN menu. 3. Roll the wheel to choose 2 [MARK] and then push the wheel or the left button. 4. Choose 9 [EBL, VRM, CURSOR SET] and then push the wheel. 5. Choose VRM1 or VRM2 as appropriate and push the wheel. 6.
1. RADAR OPERATION By trackball 1. Roll the trackball to place the arrow in the EBL1 or EBL2 box, whichever EBL you want to use. EBL1 EBL2 EBL boxes 2. The guidance box reads “EBL ON/.” Push the left button to turn on the EBL. The guidance box now reads “EBL SET L=DELETE /.” 3. Push the left button again and the cursor jumps to inside the effective display area. The guidance box now reads “EBL FIX L=DELETE/.” 4.
1. RADAR OPERATION 1.21.2 Choosing true or relative bearing The EBL readout is affixed by “R.” (relative) if it is relative to own ship's heading, ”T.” (true) if it is referenced to the north. You may choose relative or true in the head-up modes; in all other modes it is always TRUE. To choose bearing reference in the head-up mode, do the following: 1. Roll the trackball to choose the MENU box and then push the left button to open the MAIN menu. 2.
1. RADAR OPERATION 1.22 Collision Assessment by Offset EBL The origin of the EBL can be placed anywhere with the trackball to enable measurement of range and bearing between any targets. This function is also useful for assessment of the potential risk of collision. It is possible to read CPA (Closest Point of Approach) by using a VRM as shown below (Figure (a)). If the EBL passes through the sweep origin (own ship) as illustrated (Figure (b)), the target ship is on a collision course. 1.22.
1. RADAR OPERATION 330 340 350 000 010 020 330 030 320 A 020 030 040 060 070 290 070 A1 280 080 A1 050 A 300 060 290 280 010 310 050 300 350 000 320 040 310 340 080 270 090 270 090 260 100 260 100 250 110 240 No. 1 EBL EBL1 250 230 130 140 220 210 >150.3°T< 200 190 180 170 160 150 VRM1 (a) 110 240 120 No. 1 EBL >3.85NM< EBL1 120 230 130 140 220 210 200 190 >138.2°T< 180 170 160 (b) 150 VRM1 >3.
1. RADAR OPERATION 1.23 Measuring Range and Bearing Between Two Targets By keyboard 1. Press the [EBL OFFSET] key. Operate the trackball to place the origin of the No. 1 EBL, for example, on a target of interest (target 1 in the illustrated example). 2. Operate the EBL rotary control until the EBL passes through another target of interest (target 2). 3. Operate the VRM rotary control until the range marker on the EBL is on the inside edge of target 2.
1. RADAR OPERATION 1.24 Setting a Target Alarm The target alarm serves to alert the navigator to targets (ships, landmasses, etc.) entering a set area, with audible and visual alarms. CAUTION The guard alarm zone has a fixed width of 0.5 nm in the radial direction (depth) and is adjustable from 3.0 to 6.0 nm (guard zone 1) and any distance (guard zone 2). On the Non-IMO radar the boundaries can be set at any distance.
1. RADAR OPERATION Note 1: If you wish to create a target alarm zone having a 360-degree coverage around own ship, set point “B” in almost the same direction as point “A.” Note 2: Two target alarm zones may be set. Note however that the 2nd target alarm zone is available only when the 1st target alarm zone is active. Note 3: When the target alarm zone is not within the range in use the indication UP RNG appears to the right of the ALARM box.
1. RADAR OPERATION 1.24.4 Target alarm attributes You may choose the echo strength level which triggers the alarm, the condition which generates the target alarm and the volume of the audible alarm as follows: 1. Roll the trackball to choose the MENU box at the right side of the screen and then push the left button. 2. Roll the wheel to choose 3 [ALARM] and then push the wheel or the left button.
1. RADAR OPERATION 1.25 Off-Centering the Display Own ship position, or sweep origin, can be displaced to expand the view field without switching to a larger range scale. The sweep origin can be off-centered to the cursor position, but not more than 75% of the range in use; if the cursor is set beyond 75% of the range scale, the sweep origin will be off-centered to the point of 75% of the limit.
1. RADAR OPERATION 1.26 Echo Stretch The echo stretch feature enlarges targets in the range and bearing directions to make them easier to see, and it is available on any range. There are three types of echo stretch, 1, 2 and 3, and the higher the number the greater the amount of stretching. Note: The echo stretch magnifies not only small target pips but also returns (clutter) from sea surface, rain and radar interference.
1. RADAR OPERATION 1.27 Echo Averaging The echo averaging feature effectively suppresses sea clutter. Echoes received from stable targets such as ships appear on the screen at almost the same position every rotation of the antenna. On the other hand, unstable echoes such as sea clutter appear at random positions. To distinguish real target echoes from sea clutter, echoes are averaged over successive picture frames.
1. RADAR OPERATION 1.28 Target Trails The trails of the radar echoes of targets may be displayed in the form of synthetic afterglow. Target trails are chosen either relative or true and may be sea or ground stabilized. True motion trails require a compass signal and own ship speed input. 1.28.1 True or relative trails You may display echo trails in true or relative motion (only true trail on TM). Relative trails show relative movements between targets and own ship.
1. RADAR OPERATION 1.28.2 Trail time Trail time, the trail plotting interval, may be chosen as follows: 1. Roll the trackball to place the arrow on the TRAIL MODE box at the bottom right corner of the screen. * TRAIL ** * = TRUE or REL ** = Trail time setting TRAIL MODE box 2. Push the left button to choose plotting interval from among OFF, 15 s, 30 s, 1 min, 3 min, 6 min, 15 min, 30 min or CONT(INUOUS) and then push the wheel.
1. RADAR OPERATION 1.28.4 Saving, copying target trails By turning on the functions TRAIL RESTART and TRAIL COPY, you may continue painting target trails whenever the range scale is changed. The amount of range change determines how the radar paints trails. See the table below for details. Note however that if the previous range is restored within 10 seconds and the amount of range change is within 1/3, trails continue as before. If trails become difficult to view trails, you may delete them.
1. RADAR OPERATION The relationship between trail restart and trail copy depends on their status, as shown in the table below. 1.28.5 Trail restart Trail copy Trail status ON ON Range changed while trail is ON: Trails continue on targets within previous range. ON OFF Range changed while trail is ON: Trails within the previous range are erased and then trails are restarted. OFF OFF/ON • Range changed while trail is ON: New trails not initiated. (Trails from previous range are stored in memory.
1. RADAR OPERATION 1.28.7 Longer trails (B, C and W types) In addition to the trail times mentioned in paragraph 1.28.2, you may also extend trails 12 or 24 hours. 1. Roll the trackball to place the arrow on the TRAIL MODE box at the bottom right corner of the screen. 2. Push the right button to display the TRAIL menu. 3. Roll the wheel to choose 8 TRAIL LENGTH and then push the wheel or the left button. 4.
1. RADAR OPERATION 1.29 Parallel Index Lines Parallel index lines are useful for keeping a constant distance between own ship and a coastline or a partner ship when navigating. Two index lines are available and any two may be displayed. You may control the orientation and line interval. Index lines Parallel index lines 1.29.1 Displaying, erasing parallel index lines By keyboard 1. With the menu closed, press the [INDEX LINE] key. The guidance box shows “DISP INDEX LINE/.” 2.
1. RADAR OPERATION 1.29.2 Adjusting index line orientation, index line interval 1. Display the index line for which you want to adjust its orientation, referring to paragraph 1.29.1. 2. Roll the trackball to place the arrow in IL 1 ON Index line orientation the index line orientation setting 032.0°T Index line interval window, directly below the IL box. 5.60NM 3. Roll the wheel to adjust the index line orientation, between 000.0-359.9(°T).
1. RADAR OPERATION 1.29.4 Choosing maximum number of index lines to display The maximum number of index lines to display may be chosen from 2, 3 or 6 lines as below. The actual number of lines visible may be less depending on line interval. For the W specification radar, you may specify the number of lines for two sets of index lines – the menu displays 4 INDEX LINE1 and 5 INDEX LINE2. 1. Roll the trackball to choose the MENU box at the right side of the screen and then push the left button. 2.
1. RADAR OPERATION 1.30 Origin Mark You can mark any prominent target or a point of particular interest using the origin mark feature. Twenty origin marks may be entered: 10 standard origin marks (with number) and one each of the 10 symbol origin marks. The marks may be geographically fixed (ground stabilized) or sea stabilized. To display the origin marks, heading signal and own ship position data are required. 1.30.1 Entering origin marks 1.
1. RADAR OPERATION 7. With the cursor choosing the MARK box, roll the wheel to choose mark number desired (“ORIGIN MARK(No.)” chosen at step 4) or origin mark symbol (“ORIGIN MARK(SYM)” chosen at step 4) and then push the left button. The following origin marks are available. Origin mark (symbols) 8. Push the left button again. The cursor jumps into the effective display area and the guidance box now reads “MARK / EXIT.” 9. Roll the trackball to place the cursor on the location desired. 10.
1. RADAR OPERATION 1.30.2 Origin mark stabilization Origin marks may be geographically fixed (ground stabilized) or moving (sea stabilized). 1. Roll the trackball to choose the MARK box. 2. Push the right button to open the MARK menu. [MARK MENU] 1 ORIGIN MARK STAB GND/SEA 2 MARK KIND ORIGIN MARK(No. )/ ORIGIN MARK(SYM)/ MAP MARK/ WP 1~50/ WP 51~ 100/ WP 101~150/ WP 151~ 200/ OWN SHIP SHAPE 8 MARK POSN CURSOR/OS/L/L 00°000.00 N 000°000.
1. RADAR OPERATION 1.31 Zoom The zoom function enlarges an area of interest as large as twice the normal viewing size, in the text window. To use the zoom display, it must be turned on in the DATA BOX menu. For further details, see paragraph 1.41. Zoom is not available when the ARP target data setting is “LARGE” and the navigation data is turned on. 1. With the cursor inside the effective display area, roll the wheel to display “ZOOM / EXIT” in the guidance box. 2.
1. RADAR OPERATION 1.32 Markers 1.32.1 Heading marker and heading line The heading marker and the heading line indicate the ship's heading in all presentation modes. The heading line is a line from the own ship position to the outer edge of the radar display area and appears at zero degrees on the bearing scale in head-up mode; it changes the orientation depending on the ship orientation in north-up and true motion modes.
1. RADAR OPERATION 1. Roll the trackball to choose the MENU box at the right side of the display and then push the left button to display the MAIN menu. 2. Roll the wheel to choose MARK and then push the wheel or the left button to show the MARK menu. 3. Roll the wheel to choose 2 OWN SHIP MARK and then push the wheel or the left button. 4. Roll the wheel to choose OFF or ON as appropriate and then push the wheel or the left button. 5. Push the right button twice to close the menu. 1.32.
1. RADAR OPERATION 1.33 Automatic Picture Setup According to Navigation Purpose Every time your navigating environment or task changes, you must adjust the radar, which can be a nuisance in a busy situation. Instead of changing radar settings case by case, it is possible to assign the function keys to provide optimum settings for often encountered situations. The radar's internal computer offers several picture setup options to be assigned to each function key for your specific navigating requirements.
1. RADAR OPERATION Picture setup options and default settings for X-band (12 kW/25 kW) and S-band (30 kW) radars PICTURE 1 PICTURE 2 PICTURE 3 PICTURE 4 NEAR FAR NEAR BUOY FAR BUOY ROUGH SEA SHIP HARBOR COAST 1 INT REJECT 2 2 2 2 2 2 2 2 2 2 2 2 PICTURE 1 PICTURE 2 PICTURE 3 PICTURE 4 NEAR FAR NEAR BUOY FAR BUOY ROUGH SEA SHIP HARBOR COAST P/L on 0.5 nm S1 S2 S1 S1 S1 S2 S2 S2 S1 S1 S1 S1 2 ECHO STRETCH OFF 2 OFF OFF OFF 2 1 2 OFF 2 OFF OFF P/L on 0.
1. RADAR OPERATION 1.33.1 Choosing a picture setup option You may choose a picture setup options as follows: 1. Roll the trackball to choose the PICTURE box at the left side of the screen. NEAR BUOY* * Other possible indications: NEAR, FAR, FAR BUOY, ROUGH SEA, SHIP, HARBOR, COAST, NEAR BIRD, FAR BIRD, PICTURE 1 - PICTURE 4 2. Push the left button to choose picture setup option desired. 1.33.
1. RADAR OPERATION 4. Roll the wheel to choose 0 DEFAULT. 5. Push the wheel or the left button three times to restore default settings for the picture setup selected. (If you are using the keyboard, press the [ENTER MARK] key three times.) 6. Push the right button to close the menu. 1.33.3 User-programmable picture setups Four user-programmable picture setups are provided and they are labeled PICTURE 1 – PICTURE 4 in the PICTURE box. You may program them as below. 1.
1. RADAR OPERATION B: Curve between A and C. C: Mid-level in the curve is high, so this setting is suitable for detecting distant targets. 4 3 * 2 1 * B C A PICTURE level 5 db 7 db 9 db * Default 11 db VIDEO SIGNAL level Video contrast settings 7. Roll the wheel to choose 9 [CONDITION] and then push the wheel to show the CONDITION menu. [CONDITION MENU] 1 BACK 2 SEA CONDITION 1/2/3/4/5 3 ANT HEIGHT 5/7.5/10/15/20/ 25/30/35/40/45/ more50m 4 STC RANGE +00 CONDITION menu 8.
1. RADAR OPERATION 1.34 Programming Function Keys Less-often used functions are provided in the menu. To avoid opening the menus to set up the radar for a particular situation, function keys F1-F4 may be assigned any of the functions shown in the CUSTOMIZE•TEST sub menu. 1.34.1 Activating a function key To activate the function assigned to a function key, press the key to instantly set the radar for the preset purpose. Further press the key to choose option. Function key F1 F2 F3 F4 1.34.
1. RADAR OPERATION 4. Roll the wheel to choose appropriate category, ECHO, STD KEY, ARP•AIS, OPERATION or PICTURE and then push the wheel or the left button. Refer to the menus below to choose appropriate category.
1. RADAR OPERATION 5. Roll the wheel to choose “2” and then push the wheel or the left button. 6. Roll the wheel to choose function desired and then push the wheel or left button. 7. Push the right button twice to close the menu. Description of function key programs Item [ECHO] PICTURE Description Chooses picture setup function.
1.
1. RADAR OPERATION Description of function key programs (con’t from previous page) Item [PICTURE] PICTURE1 – PICTURE4 NEAR FAR NEAR BUOY FAR BUOY ROUGH SEA SHIP HARBOR COAST NEAR BIRD FAR BIRD 1-68 Description Actuates settings of user-programmed setup.
1. RADAR OPERATION 1.35 Ship’s Position Choose the source of ship’s position data as follows: 1. Roll the trackball to choose the OS POSN box at the top right corner of the screen. OS POSN OS POSN box 2. Push the right button to show the OS POSN menu. [OS POSN MENU] 1 NAV AID GPS1/GPS2/ DEAD RECKONING/ LAN 2 MANUAL L/L 00°00.00 N 000°00.00 W 3 SIO DATA LAN OUTPUT OFF/ON OS POSN menu 3. Roll the wheel to choose 1 NAV AID and then push the wheel or the left button. 4.
1. RADAR OPERATION 1.36 Noise Rejector White noise may show itself on the screen as random “speckles” spread over the entire radar image. You can remove this noise as follows: 1. Roll the trackball to choose the PICTURE box at the left side of the screen. 2. Push the right button to open the PICTURE menu.
1. RADAR OPERATION 1.37 Suppressing Second-trace Echoes In certain situations, echoes from very distance targets may appear as false echoes (second-trace echoes) on the screen. This occurs when the return echo is received one transmission cycle later, or after a next radar pulse has been transmitted. Tx repetition Second-trace echo False echo range Actual range Second-trace echoes To reject second-trace echoes: 1.
1. RADAR OPERATION 1.38 Adjusting Brilliance of Screen Data You can adjust relative brilliance levels of various markers and alphanumeric readouts displayed on the screen. 1. Roll the trackball to choose the BRILL box at the bottom left corner of the screen and then push the right button to show the BRILL menu.
1. RADAR OPERATION 1.39 Watch Alarm The watch alarm sounds the audible alarm at the chosen time interval to help you keep regular watch of the radar picture for safety or other purposes. The WATCH box appears at the lower-left corner of the screen with a watch alarm timer counts down from value set (for example, “12:00”). WATCH 12:00 WATCH box When a preset time interval has elapsed, the audible watch alarm is released, the screen label WATCH turns red and the watch alarm timer freezes at “0:00.
1. RADAR OPERATION 1.40 Setting Up Nav Data Wind, depth, ocean current, water temperature, date and time and waypoint data may be set up as follows: 1. Roll the trackball to choose the MENU box at the right side of the screen and then push the left button. 2. Roll the wheel to choose 7 NAV DATA and then push left button to open the NAV DATA menu.
1. RADAR OPERATION Nav data menu description Item Description 2 DEPTH Chooses unit of depth measurement, or turn depth indication off. 3 DEPTH GRAPH SCALE Chooses depth scale range. The echogram shows the last 30 minutes of sounding along the ship’s track. 4 DEPTH MARK Chooses the depth at which to show the depth mark. 5 CURRENT Turns ocean current display on (ocean current relative to North) or off. 6 WIND Chooses unit of wind speed measurement, or turn wind indication off.
1. RADAR OPERATION 1.41 Text Window Setup The text window, displayed at the right 1/4 of the screen, mainly shows nav data, zoomed target, and ARP target data. You can set up this window as follows: 1. Roll the trackball to choose the MENU box at the right side of the screen and then push the left button. 2. Roll the wheel to choose 9 [CUSTOMIZE•TEST] and then push the wheel or the left button. [CUSTOMIZE•TEST] 1 2 3 4 5 6 7 8 BACK [DATA BOX] [F1] [F2] [F3] [F4] [OPERATION] [TEST] CUSTOMIZE•TEST menu 3.
1. RADAR OPERATION 10. Roll the wheel to choose zoom display format and then push the wheel or the left button. REL: Zoom display moves in relative motion STAB: Zoom display is ground stabilized (geographically fixed) ACQ: Zoom ARP targets 11. Roll the wheel to choose 6 TARGET DATA and then push the wheel or the left button. 12. Roll the wheel to choose quantity of ARP target data to show among 1BOX, 2BOX, 3BOX and LARGE and then push the wheel or the left button.
1. RADAR OPERATION 1.42 Customizing Operation Several operation items may be customized to suit your needs. 1. Roll the trackball to choose the MENU box at the right side of the screen and then push the left button. 2. Roll the wheel to choose 9 [CUSTOMIZE•TEST] and then push the wheel or the left button to open the CUSTOMIZE•TEST menu. [CUSTOMIZE•TEST] 1 2 3 4 5 6 7 8 BACK [DATA BOX] [F1] [F2] [F3] [F4] [OPERATION] [TEST] CUSTOMIZE•TEST menu 3.
1. RADAR OPERATION Operation menu items Item No. 2 WHEEL DRIVE 3 KEY BEEP 4 REMOTE KEY 5 POP UP GUIDANCE (Available on B, C and W types) 6 OWN SHIP VECTOR 7 STERN-UP (Not available on IMO or A type) 8 SHUTTLE FERRY Description Options Choose how to cycle data when NORMAL: Cycles numeral using the wheel. data in numeric order and indication data in clockwise order. REVERSE: Reverse of NORMAL. Key beeps when key sequence OFF: No key beep has been correctly executed.
1. RADAR OPERATION 1.43 Alarms When error is detected, the appropriate alarm indication appears (in red) and the audible alarm sounds. Silence the audible alarm with the [ALARM ACK] key or choose the ALARM ACK box and then push the left button. The error indication remains on the display until the reason for the alarm is removed. 1.43.1 Alarm description Alarm description Warning GYRO failure Audible alarm 2 beeps Visual alarm HDG indication reads “***.
1. RADAR OPERATION Alarm description (con’t from previous page) Warning Audible alarm Visual alarm To quit alarm status EPFS failure Continuous EPFS in red (EPFS: electronic beep position-fixing system) in the warning and indication cell. The indication also appears when the GPS mode is switched between GPS and DGPS. SOG indication none COLLISION Continuous COLLISION comes on when beep ARP-tracked target is on collision course.
1. RADAR OPERATION 1.43.2 Outputting alarm signal Four ports are provided from which to output alarm signals to external equipment. Choose the port and alarm signals to output as follows: 1. Roll the trackball to choose the MENU box and then push the left button. 2. Roll the wheel to choose 3 ALARM and then push the wheel or the left button.
1. RADAR OPERATION 4. Roll the wheel to choose an alarm to output and then push the wheel or the left button. The alarm chosen is underlined. 5. Repeat step 5 to choose other alarms to output. 6. Push the right button three times to close the menu. 1.44 Choosing the Antenna, Displaying Antenna Information This radar’s interswitch uses an Ethernet to exchange video and control signals and actual interswitching is done with a digitized signal. Max. 4 antennas may be selected from the menu. 1.44.
1. RADAR OPERATION 1.44.2 Displaying antenna information The antenna information display shows data (radar band, model and position) on the radar antennas currently powered. If an antenna is not powered, its data area is blank. 1. Roll the trackball to place the arrow in the ANTENNA box at the left side of the screen. 2. Push the left button to choose the antenna for which you want to find information. (You cannot choose an antenna which does not exist or one which is not powered.) 3.
1. RADAR OPERATION 1.45 Cursor Data Cursor data can be shown in range and bearing from own ship, latitude and longitude position or cursor’s X-Y coordinates. 1. Roll the trackball to choose the CURSOR DATA box at the right side of the display. 34°40.849 N + 135°18.303 E CURSOR DATA box (L/L position) 2. Push the left button to choose the cursor data to show. The cursor data changes in the sequence shown below. + 1351.2°T 13.67NM Range and bearing from own ship to cursor position 34°30.
1. RADAR OPERATION 1.46 Performance Monitor A performance monitor is required for a radar installed on vessels of 300 GT and upward engaged in international voyages. Two units are available: X-band radar: PM-31 (9410 ± 45 MHz) S-band radar: PM-51 (3050 ± 30 MHz). The performance monitor is incorporated in the antenna unit. Note that neither FAR-2157 nor FAR-2167DS carry a performance monitor. 1.46.1 Activating, deactivating the performance monitor 1.
1. RADAR OPERATION The range scale is automatically set to 24 nm. The radar screen will show one or two arcs. If the radar transmitter and receiver are in good working conditions in as much as the original state when the monitor was turned up, the innermost arcs should appear between 13.5 to 18.5 nm. The performance monitor can observe a total of 10 dB loss in transmitter and receiver. Display Radar State Transmitter: normal Receiver: normal 13.5 nm 18.
1. RADAR OPERATION 1.47 Wiper The wiper feature automatically suppresses the brilliance of weak signals (noise, sea clutter, rain clutter, etc.) and unwanted signals such as radar interference to clear the picture of unwanted echoes. Its effect depends on the wiper setting used and whether each averaging is turned on or off, as described below.
1. RADAR OPERATION 1.48 Own Ship Symbol Own ship symbol ( ) may be inscribed on the screen as below. You may enter ten such symbols. Each own ship symbols is shown with a number. 1. Roll the trackball to choose the MARK box at the left side of the screen. The guidance box now reads “MARK SELECT / MARK MENU.” MARK Mark type last selected, mark number 1 -> + - - -m, - - -m Dimensions of own ship Mark box 2. Push the right button to open the MARK menu.
1. RADAR OPERATION 1.49 Color and Brilliance Sets This radar provides four sets of color and brilliance sets to match any ambient lighting condition. The default colors are as shown in the table below. The default brilliance setting for any item is “50%”. BRILL1 Yellow Black, Black Echo Inside Display, Outside Display Menu Yellow Characters Green Bearing Scale Blue 1.49.
1. RADAR OPERATION 5. Roll the wheel to choose 2 BKGD COLOR and then push the wheel or the left button. 6. Roll the wheel to choose background color and surrounding color combination desired and then push the wheel or the left button. 7. Set brilliance-related items referring to paragraph 1.38. 8. Push the right button to close the BRILL menu. 1.50 Reference Point for CPA/TCPA The common reference point for CPA/TCPA can be chosen from antenna position or conning position as shown below.
1. RADAR OPERATION 1.51 Switching Hub HUB-100 (option) The HUB-100 provides switching for a card interface unit and multiple processor units (max. 7), using an Ethernet interface (100BASE-TX/10BASE-T). LEDs display link/activity, mode (full-duplex or half-duplex) and collision statuses. No operation is required of the user. Simply turn on the HUB-100’s AC power source to power it. LED display The LEDs on the top of the unit light, flash or go off according to equipment status.
1. RADAR OPERATION 1.52 Dual Radar Display The image from both X-band and S-band radars may be shown together on one radar display. This allows you to take advantage of the best characteristics each type of radar has to offer. Two display formats are available, mixed and combine, and you may select desired format from the menu.
1. RADAR OPERATION Note 2: In the dual radar display, a guard zone set on the main radar is also accommodated on the external radar. When the position of the antennas for the main and external radars is different and the No. 2 guard zone is set on a close-in range, the on-screen guard zone may be shifted slightly from both the main radar antenna reference and external radar antenna reference. Accordingly, on the dual radar display, the actual guard zone area may be shifted slightly.
1. RADAR OPERATION 7. Push the right button four times to close the menu. Note 1: The dual radar function becomes inoperative when the external radar is turned off, set to stand-by, or set as sub display. When this happens, the buzzer sounds and the message "EXT-STBY" (power off, stand-by only) appears. Note 2: The dual radar display is inoperative on the stern-up and shuttle ferry modes. For more information about these modes see the FAR-2xx7 Operator’s Manual.
1. RADAR OPERATION 1.52.2 Specifying Sector Width and Length When 2 DUAL RADAR in the DUAL RADAR menu is set for "COMBINE", specify the width and length of the sector from the external radar to display on own radar. 1. Right-click the MENU box. 2. Select 9 [CUSTOMIZE, TEST] and push the left button. 3. Select 7 [OPERATION] and push the left button. 4. Select 9 [DUAL RADAR] and push the left button. 5. Select 3 COMBINE MODE and push the left button. 6. Select OWN or EXT and push the left button.
1. RADAR OPERATION In the example below, START is 130° and ANGLE is 100°. Width of sector ANGLE (Example: 100°) START (Example: 130°) 9. Select 5 COMBINE RANGE and push the left button. 10. Use the scrollwheel to set START and LENGTH, referring to the example below. Spin the scrollwheel to set and push it to confirm. • START: Set range start point. • LENGTH: Set length of sector. START LENGTH Example: START: 01.00 nm LENGTH: 02.00 nm Push the right button four times to close the menu.
1. RADAR OPERATION 1.52.3 Choosing External Radar (image source) Select the external radar to use in the dual radar display. 1. Right-click the MENU box. 2. Select 9 [CUSTOMIZE, TEST] and push the left button. 3. Select 7 [OPERATION] and push the left button. 4. Select 9 [DUAL RADAR] and push the left button. [DUAL RADAR] 1 BACK 2 DUAL RADAR OFF/MIX/COMBINE 3 COMBINE MODE* OWN/EXT 4 COMBINE SECTOR* START 000° ANGLE 000° 5 COMBINE RANGE* START 00.00NM LENGTH 00.
2. RADAR OBSERVATION 2.1 General 2.1.1 Minimum and maximum ranges Minimum range The minimum range is defined by the shortest distance at which, using a scale of 1.5 or 0.75 nm, a target having an echoing area of 10 m2 is still shown separate from the point representing the antenna position. It is mainly dependent on the pulselength, antenna height, and signal processing such as main bang suppression and digital quantization.
2. RADAR OBSERVATION X-band and S-band In fair weather, the equation on the previous page does not give a significant difference between X- and S-band radars. However, in heavy precipitation condition, an S-band radar would have better detection than an X-band radar. Radar resolution There are two important factors in radar resolution (discrimination): bearing resolution and range resolution.
2. RADAR OBSERVATION 2.2 False Echoes Occasionally echo signals appear on the screen at positions where there is no target or disappear even if there are targets. They are, however, recognized if you understand the reason why they are displayed. Typical false echoes are shown below. Multiple echoes Multiple echoes occur when a transmitted pulse returns from a solid object like a large ship, bridge, or breakwater.
2. RADAR OBSERVATION Virtual image A relatively large target close to your ship may be represented at two positions on the screen. One of them is the true echo directly reflected by the target and the other is a false echo which is caused by the mirror effect of a large object on or close to your ship as shown in the figure below. If your ship comes close to a large metal bridge, for example, such a false echo may temporarily be seen on the screen.
2. RADAR OBSERVATION 2.3 SART (Search and Rescue Transponder) 2.3.1 SART description A Search and Rescue Transponder (SART) may be triggered by any X-Band (3 cm) radar within a range of approximately 8 nm. Each radar pulse received causes it to transmit a response which is swept repetitively across the complete radar frequency band. When interrogated, it first sweeps rapidly (0.4 µs) through the band before beginning a relatively slow sweep (7.5 µs) through the band back to the starting frequency.
2. RADAR OBSERVATION 2.3.2 Showing SART marks on the radar display This radar is equipped with a feature which optimally sets up the radar for SART detection. This feature automatically detunes the radar receiver out of its best tuning condition. This erases or weakens all normal radar echoes, but the SART marks are not erased because the SART response signal scans over all frequencies in the 9 GHz band.
2. RADAR OBSERVATION 2.3.3 General remarks on receiving SART SART range errors When responses from only the 12 low frequency sweeps are visible (when the SART is at a range greater than about 1 nm), the position at which the first dot is displayed may be as much as 0.64 nm beyond the true position of the SART. When the range closes so that the fast sweep responses are seen also, the first of these will be no more than 150 meters beyond the true position.
2. RADAR OBSERVATION 2.4 RACON A RACON is a radar beacon which emits radar receivable signals in the radar frequency spectrum (X- or S-band). There are several signal formats; in general, the RACON signal appears on the radar screen as a rectangular echo originating at a point just beyond the position of the radar beacon. It has a Morse coded pattern. Note that the position on the radar display is not accurate.
3. ARP OPERATION 3.1 Usage Precautions • This function is designed to meet the IMO requirements of both ARPA and ATA, and the desired function is selected during the installation of the equipment. For sake of brevity, this manual uses “ARP” when referring to ARPA or ATA. • The plotting accuracy and response of this ARP meets IMO standards. Tracking accuracy is affected by the following: • Tracking accuracy is affected by course change.
3. ARP OPERATION 3.2 Controls for ARP Keyboard The ARP uses the keys shown below. BRILL OFF A/C RAIN A/C SEA GAIN ON EBL OFF ON 3 1 HL OFF 2 EBL OFFSET MODE F1 F2 4 OFF CENTER 5 CU/TM RESET 6 INDEX LINE F3 F4 7 VECTOR TIME 8 VECTOR MODE 9 TARGET LIST ALARM ACK STBY TX CANCEL TRAILS 0 ENTER BRILL MARK VRM MENU + ACQ TARGET DATA RANGE TARGET CANCEL - ACQ: TARGET DATA: Manually acquires a target. Displays data on ARP target chosen with the trackball.
3. ARP OPERATION 3.3 Activating, Deactivating ARP To activate or deactivate the ARP: 1. Roll the trackball to place the arrow in the ARP ACQ MODE box at the right side of the display. (Note that “ATA” replaces “ARPA” when the ATA feature is used.) ARPA AUTO MAN ARPA ACQ MODE box 2. Push the left button to show OFF, MAN or AUTO MAN as appropriate. 3.4 Entering Own Ship's Speed The ARP requires own ship's speed and heading data. The speed can be STW, BT, SOG or echo-referenced speed (based on 3 max.
3. ARP OPERATION 4. Push the left button to enter the reference mark. (The mark may also be entered by pressing the [ENTER MARK] key on the full keyboard.) The reference target mark (see below) appears at the cursor position and the own ship position data label changes from “LOG,” “NAV” or “MANUAL” to “REF.” Note that it takes 60 scans or approximately 1 min before a new speed is displayed.
3. ARP OPERATION 3.5 Automatic Acquisition The FAR-2xx7 radars can acquire a maximum of 100 targets, the number of automatically and manually acquired targets determined by the ARP TGT menu setting.
3. ARP OPERATION 3.5.2 Terminating tracking of targets (including reference targets) When the ARP has acquired the menu-set number of targets automatically, the message “TARGET-FULL(AUTO)” appears at the right side of the screen and no more auto acquisition occurs unless targets are lost. Should this happen, cancel tracking of less important targets or perform manual acquisition. Canceling individual targets By keyboard: 1.
3. ARP OPERATION 3.6 Manual Acquisition Maximum 100 targets may be acquired manually depending on the acquisition condition set on the ARP TGT menu. 3.6.1 Setting manual acquisition conditions 1. Roll the trackball to place the arrow in the ARP ACQ MODE box at the right side of the screen and then push the right button to show the ARP TARGET menu. [ARP TARGET MENU] 1 ARP SELECT MANUAL100/ AUTO 25/ AUTO 50/ AUTO 75/ AUTO 100 2 ALL CANCEL 3 REF TARGET VECTOR ARP TARGET menu 2.
3. ARP OPERATION The plotting symbol is drawn by broken lines during the initial acquisition stage. A vector appears in about one minute after acquisition indicating the target's motion trend. If the target is consistently detected for three minutes, the plotting symbol changes to a solid circle. If acquisition fails, the target plotting symbol blinks and disappears shortly. ARP Symbol Meaning Immediately after acquisition, this plotting symbol is shown in broken lines.
3. ARP OPERATION 3.7 ARP Symbols and ARP Symbol Attributes 3.7.1 ARP symbols The symbols used in this equipment comply with IEC 60872-1. Item Symbol Status Remarks Initial stage Broken square around an echo to indicate Automatically the target under acquisition and initial acquired targets stage of tracking, before steady-state tracking.
3. ARP OPERATION Other ARP symbols Item Symbol Trial maneuver T Status Bottom center Appears during execution of a trial maneuver. Bottom center Appears during performance test. (flashing) Performance test 3.7.2 XX Remarks (flashing) Choosing ARP symbol (B, C and W types) In addition to the “standard” circle ARP symbol you may choose from the symbols shown below. 1. Place the cursor on the ARP symbol you want to change. 2.
3. ARP OPERATION 3.7.4 ARP symbol color and size You may choose the color and size of the ARP symbol as follows: 1. Roll the trackball to choose the MENU box at the right side of the screen and then push the left button. 2. Roll the wheel to choose 4 ARP•AIS and then push the wheel or the left button.
3. ARP OPERATION 3.7.5 Auto target track (A, B, C and W types) You may “reuse” ARP target numbers 1-15 when an ARP target having one of those target numbers becomes a lost target. 1. Roll the trackball to choose the MENU box at the right side of the screen and then push the left button. 2. Roll the wheel to choose 5 PLOTTER and then push the wheel or the left button. 3. Roll the wheel to choose 0 AUTO TARGET TRACK and the push the wheel or left button. 4.
3. ARP OPERATION 3.8 Displaying Target Data The ARP mode provides the full functionality of ARP as required by the IMO Resolution A.823(19) and IEC 60972-1, including display of range, bearing, course, speed, CPA and TCPA of all plotted targets. In head-up and head-up true bearing modes, target bearing, course and speed shown in the upper-right target data field become true (suffix “T”) or relative (suffix “R”) to own ship in accordance with the true/relative vector setting.
3. ARP OPERATION Target in guard zone Target selected for data readout Target on colllision course 330 340 350 000 010 020 030 320 040 310 050 01 060 300 070 290 280 080 270 090 260 100 250 110 240 120 230 ARP TARGET No. 01 BRG 25.5°T RNG 3.4NM T COG 205.1°T* T SOG 12.3KT* CPA 2.9NM TCPA 12.2MIN BCR 1.7NM BCT 20MIN 130 140 220 210 200 190 180 170 * CSE and STW are shown in case of manual input.
3. ARP OPERATION 3.8.2 Target list The target list provides a comprehensive data display of all ARP (and AIS) targets being tracked. Displaying the target list To display the target list, do the following: 1. Roll the trackball to choose the TARGET LIST box at the right side of the screen. TARGET LIST TARGET LIST box 2. Push the left button to display the TARGET LIST. “>” in the TCPA means that the time is greater than 99:59. [TARGET LIST (1/1)] SORT BY CPA 1 BACK 2 ARP TARGET No: 001 BRG 16.5°T RNG 2.
3. ARP OPERATION Sorting the target list You may sort the target list by CPA, TCPA, BCR, BCT, RANGE or SPEED as follows: 72 nm or 96 nm range scale 1. Roll the trackball to choose the TARGET LIST box at the right side of the screen. 2. Push the right button to open the TARGET LIST menu. [TARGET LIST MENU] 1 SORT BY CPA/TCPA/BCR/BCT/ RANGE/SPEED TARGET LIST menu 3. Roll the wheel to choose 1 SORT BY and then push the wheel or the left button. 4.
3. ARP OPERATION 3.9 Vector Modes Target vectors can be displayed relative to own ship's heading (Relative) or north (True). 3.9.1 Description of vectors Ground stabilization and sea stabilization Target vectors can be ground stabilized or sea stabilized. Sea stabilization is a mode where own ship and all targets are referenced to the sea using a compass heading and single axis log water speed inputs in the True Motion mode.
3. ARP OPERATION 3.9.2 Vector motion and length Vectors may be displayed in true or relative motion. Vector time (or the length of vectors) can be set to 30 seconds, 1-15 minutes (in one-minute intervals), 20 minutes and 30 minutes. By keyboard 1. Press the [VECTOR MODE] key consecutively to choose relative or true vector mode. Your selection is shown on the Vector motion box. (Note that this also selects the vector mode for the past position display.) 2.
3. ARP OPERATION 3.10 Past Position Display The ARP displays equally time-spaced dots marking the past positions of any targets being tracked. A new dot is added every minute (or at other preset time intervals) until the preset number is reached. If a target changes its speed, the spacing will be uneven. If it changes the course, its plotted course will not be a straight line. (a) Ship turning (b) Ship running straight (c) Ship reduced speed (d) Ship increased speed Past position display 3.10.
3. ARP OPERATION 3.10.2 Past position display attributes You may choose the number of past point points to display per plotting interval and the color of past position points. 1. Roll the trackball to choose the MENU box at the right side of the screen and then push the left button. 2. Roll the wheel to choose 4 ARP•AIS and then push the wheel or the left button.
3. ARP OPERATION 3.11 Set and Drift Set, the direction in which a water current flows, can be manually entered in 0.1-degree steps. Drift, in another word Rate, the speed of tide, can also be entered manually in 0.1 knot steps. Set and drift corrections are beneficial for increasing the accuracy of vectors and target data. Refer to the tide table on board the ship for setting information. These values are applied to all targets.
3. ARP OPERATION 3.12 Setting CPA/TCPA Alarm Ranges The ARP continuously monitors the CAUTION predicted range at the Closest Point of Approach (CPA) and predicted time to CPA CPA/TCPA Alarm (TCPA) of each tracked target to own ship. The CPA and TCPA alarm feature should never be relied upon as the sole means for When the predicted CPA of any target detecting the risk of collision.
3. ARP OPERATION 3.12.2 Acknowledging CPA/TCPA alarm To acknowledge and silence the CPA/TCPA alarm, press the [ALARM ACK] key on the keyboard, or choose the ALARM ACK box with the trackball and then push the left button. The warning label COLLISION and the flashing of the triangle plotting symbol and vector remain on the screen until the dangerous situation is gone or you intentionally terminate tracking of the target.
3. ARP OPERATION 3.13 Setting a Guard Zone When a target transits the operator-set guard zone, the buzzer sounds and the indication GUARD appears (in red) at the screen bottom. The target causing the warning is clearly indicated with an inverted flashing triangle. The guard zone also functions as an automatic acquisition area when automatic acquisition is active. Any targets entering the zone will be automatically acquired. 3.13.1 Activating the guard zone One or two guard zones may be selected. The No.
3. ARP OPERATION When an ARP or AIS target violates the guard zone, the message “GUARD” appears (in red) at the right side of the display and the offending target is marked with an inverted triangle. Further, the AIS display is automatically turned on. Note 1: If you wish to create a guard zone having a 360-degree coverage around own ship, set point B in almost the same direction (approx. ±3°) as point A and then push the left button.
3. ARP OPERATION 3.13.4 Guard zone reference The guard zone may be referenced to heading or North as follows: 1. Roll the trackball to choose the MENU box at the right side of the screen and then push the left button. 2. Roll the wheel to choose 4 ARP•AIS and then push the wheel or the left button.
3. ARP OPERATION 4. Roll the wheel to choose OFF, STAB GND, STAB HDG or STAB NORTH as appropriate and then the push the wheel or the left button. OFF: Guard zone is a sector; number of points limited to four. STAB GND: Guard zone stabilized against ground; guard zone may be a polygon having 3-10 points. STAB HDG: Guard zone stabilized against heading; guard zone may be a polygon having 3-10 points. STAB NORTH: Guard zone stabilized against ground; guard zone may be a polygon having 3-10 points. 5.
3. ARP OPERATION Target full alarm When the memory becomes full, the memory full status is indicated by “TARGET-FULL(AUTO+MAN)” and the relevant indication appears on the screen and a short beep sounds. Manually acquired targets The indication “TARGET-FULL(MAN)” appears at the screen bottom and a short beep tone sounds when the capacity for manually acquired targets, as set on the menu, is reached.
3. ARP OPERATION 3.15 Trial Maneuver The trial maneuver feature simulates the effect on all tracked targets against own ship's maneuver without interrupting the updating of target information. It is available for use with the ARPA function; it is inoperative on the ATA. 3.15.1 Types of trial maneuvers There are two types of trial maneuvers: static and dynamic. Dynamic trial maneuver A dynamic trial maneuver displays predicted positions of the tracked targets and own ship.
3. ARP OPERATION Static trial maneuver A static trial maneuver displays only the final situation of the simulation. If you enter the same trial speed, course and delay time under the same situation as in the aforementioned example of dynamic trial maneuver, the screen will instantly show position OS7 for own ship, position A7 for target A and position B7 for target B, omitting the intermediate positions.
3. ARP OPERATION 3. Roll the wheel to choose 4 TRIAL MANEUVER and then push the wheel or the left button. [TRIAL MANEUVER] 1 BACK 2 TRIAL OFF/STATIC/DYNAMIC 3 TRIAL SPEED RATE 0kt 0.00kt/s 0kt 0.00kt/s 4 TRIAL TURN RATE 0kt 0.0°/s 0kt 0.0°/s 4. 5. 6. 7. TRIAL MANEUVER menu Roll the wheel to choose 2 TRIAL and then push the left button or the wheel. Roll the wheel to choose STATIC or DYNAMIC as appropriate and then push the wheel or the left button. Roll the wheel to choose 3 TRIAL SPEED RATE.
3. ARP OPERATION 11. Roll the wheel to choose the course setting box. Use the wheel to set the course: Roll the wheel to choose location; push the wheel to set. 12. Roll the wheel to choose the speed setting box. Use the wheel to set the speed: Roll the wheel to choose location; push the wheel to set. 13. Roll the wheel to choose TRIAL SET. Push the left button or the wheel to show TRIAL WORK. The trial maneuver takes place for three minutes with the letter “T” displayed at the bottom of the screen.
3. ARP OPERATION 3.16 ARP Performance Test A test program is provided for assessing overall performance of the ARP. Normal operation is suspended and the indication “XX” appears at the bottom of the effective display area during the test. The test may be terminated at any time. 1. Roll the trackball to choose the MENU box and then push the left button. 2. Roll the wheel to choose 9 [CUSTOMIZE•TEST] and then push the wheel or the left button.
3. ARP OPERATION 5. Roll the wheel to choose 2 ARP TEST START and then push the wheel or the left button to start the test. An alert “XX” flickers during the test. It takes approximately three minutes for all vectors to be displayed. The test does not need echo signals, gyro nor speed log input. The operator shall set speed for 0 kt and course for 0°T. 6. Three targets having different speeds and courses, as shown in the table below, are simulated automatically, together with current targets. 7.
3. ARP OPERATION 3.17 Criteria for Selecting Targets for Tracking The FURUNO ARP video processor detects targets in midst of noise and discriminates radar echoes on the basis of their size. Target whose echo measurements are greater than those of the largest ship in range or tangential extent are usually land and are displayed only as normal radar video.
3. ARP OPERATION This land outline is used to inhibit further acquisition and tracking of ship-sized echoes beyond the closest coast outline. Five consecutive scans of coastal outline are retained in memory to allow for signal variation. All smaller echoes are declared to be ship sized and the middle of the leading edge is used to provide precise range and bearing coordinates of each echo on every scan. This range/bearing data is matched to previous data and analyzed from scan-to-scan for consistency.
3. ARP OPERATION 3.18 Factors Affecting ARP Functions Sea returns If the radar anti-clutter control is adjusted properly, there is no serious effect because distant wave clutter, not eliminated by this control, is filtered out by more than one bang correlation and scan-to-scan matching of data. Rain and snow Clutter can be acquired and tracked as targets. Adjust the A/C RAIN control. If it is heavy rain, switch to S-band if provided, or switch on the interference rejector on the radar.
3. ARP OPERATION Blind and shadow sectors Radar shadow or blind areas caused by obstructions aboard ship, for example, funnels and masts, in the path of the radar beam can result in reduction of radar beam intensity in that particular direction. This may eliminate the detection of some targets. The ARP system will lose track of targets shortly after they are lost on the radar picture and if they remain in a blind zone.
4. AIS OPERATION The FURUNO AIS (Automatic Identification System) model FA-100 or FA-150 exchanges with other AIS-fitted ships all data and information required by the SOLAS 1994 as amended. However, they are displayed in text form. By interfacing the FA-100 or FA-150 with this radar, the AIS information is graphically indicated together with the radar and ARP information. This radar accepts position data fixed by WGS-84 geodetic datum. Set the datum to WGS-84 on the EPFS (GPS, etc.
4. AIS OPERATION 4.2 Enabling/Disabling the AIS 1. Roll the trackball to choose the MENU box at the right side of the screen and then push the left button. 2. Roll the wheel to choose 4 ARP•AIS and then push the wheel or the left button. [ARP•AIS] 1 BACK 2 GUARD ZONE STAB STAB HDG/STAB NORTH 3 GUARD POLYGON OFF/STAB GND/ STAB HDG/STAB NORTH 4 [TRIAL MANEUVER] 5 [ARP SYMBOL] 6 [AIS SYMBOL] 7 [FUSION] 8 AIS FUNCTION OFF/ON 9 AIS LOST ALARM ACTIVATED TARGET/ ALL TARGET/ RANGE 0nm ARP•AIS menu 3.
4. AIS OPERATION 4.3 Turning AIS Display On/Off 1. Roll the trackball to choose the AIS DISP box at the right side of the screen. AIS DISP OFF AIS DISP box 2. Push the left button to display AIS ON or AIS OFF as appropriate. ON: All targets received from the AIS transponder are displayed with symbols. OFF: All AIS symbols disappear. When the AIS is turned on, AIS targets are marked with appropriate AIS symbol as below.
4. AIS OPERATION 4.4 Setting Up for a Voyage There are five items on the VOYAGE DATA menu you will need to enter at the start of a voyage: navigational status, ETA, destination, draught and crew. 1. Roll the trackball to choose the AIS DISP box at the right side of the screen. 2. Push the right button to open the AIS TARGET menu.
4. AIS OPERATION 5. Roll the wheel to choose appropriate navigation status number referring to the information below. Push the wheel. 00: 01: 02: 03: 04: 05: 06: 07: 08: 09: 10: 11-15: Underway using engine (default) At anchor Not under command Restricted maneuverability Constrained by her draught Moored Aground Engaged in fishing Under way sailing Reserved for high speed craft (HSC) Reserved for wing in ground (WIG, for example, hydrofoil) Reserved for future use 6.
4. AIS OPERATION 4.5 Activating Targets When you convert a sleeping target to an activated target, that target’s course and speed are shown with a vector. You can easily judge target movement by monitoring the vector. 4.5.1 Activating specific target By keyboard 1. Roll the trackball to place the cursor on the AIS target you wish activate. 2. Press the [ACQ] key to activate the target. By trackball 1.
4. AIS OPERATION 4.6 Sleeping Targets 4.6.1 Sleeping an AIS target You may “sleep” an AIS target as below when the screen becomes filled with targets which might prevent important radar and AIS displays from being identified. Note that targets that have been activated automatically cannot be “slept.” 1. With the cursor inside the effective display area, roll the wheel to display “TARGET CANCEL / EXIT” in the guidance box. 2. Roll the trackball to place the cursor on an activated AIS target symbol. 3.
4. AIS OPERATION 4.7 Displaying Target Data You may display an AIS target’s data by selecting it on the display. 4.7.1 Basic data By keyboard 1. Roll the trackball to place the cursor on the AIS target symbol you want to know its data. 2. Press the [TARGET DATA] key. By trackball 1. With the cursor inside the effective display area, roll the wheel to display “TARGET DATA & ACQ / CURSOR MENU”. 2. Roll the trackball to place the cursor on an AIS target symbol and then push the wheel or the left button.
4. AIS OPERATION 4.7.2 Detailed target data 1. Roll the trackball to place the cursor on the desired AIS target in the data box at the right side of the screen. 2. Push the left button to show detailed data. [EXPANDED DATA] Ship's name Call sign Latitude Longitude Position fixing device Position accuracy (HIGH, LOW) Navigation status MMSI No. IMO No. Length Width Draft Destination Estimated Time of Arrival AIS program no. Fusion ON/OFF Type of ship and cargo NAME: VOYAGER CALL: 143678 LAT: 34°44.
4. AIS OPERATION 4.8 AIS Symbol Attributes You may adjust the brilliance and choose the size and color of the AIS symbol. 4.8.1 AIS symbol brilliance 1. Roll the trackball to choose the BRILL box at the left side of the screen and then push the right button. 2. Roll the wheel to choose 0 NEXT and then push the wheel or the left button.
4. AIS OPERATION 4.8.2 AIS symbol size and color You may choose the size and color of the AIS symbol as follows: 1. Roll the trackball to choose the MENU box and then push the left button. 2. Roll the wheel to choose 4 [ARP•AIS] and then push the wheel or the left button. 3. Roll the wheel to choose 6 [AIS SYMBOL] and then push the wheel or the left button. [AIS SYMBOL] 1 BACK 2 AIS SYMBOL COLOR RED/GRN/BLU/YEL/ CYA/MAG/WHT 3 AIS SYMBOL SIZE SMALL/STD/LARGE 4 ROT TAG LIMIT 000.
4. AIS OPERATION 4.9 Past Position Display The past position display shows equally time-spaced dots marking past positions of activated AIS targets. A new dot is added at preset time intervals until the preset number is reached. If a target changes its speed, the spacing will be uneven. If it changes course, its plotted course will not be a straight line.
4. AIS OPERATION 4.9.2 Past position display attributes You may choose the number of past position points to show per plot interval and the color of past position points. 1. Roll the trackball to choose the MENU box and then push the left button. 2. Roll the wheel to choose 4 ARP•AIS and then push the wheel or the left button. 3. Roll the wheel to choose 7 [AIS SYMBOL] and then push the wheel or the left button.
4. AIS OPERATION 4.10 Lost Target A target is declared a lost target when it fails to produce data for six minutes or five reporting intervals, whichever is the shorter. When this occurs, the target is marked with the (flashing) lost target symbol and the indication “LOST” appears. To acknowledge a lost target, press the [ALARM ACK] key or roll the trackball to choose the ALARM ACK box and then push the left button.
4. AIS OPERATION 4.11 ROT Setting You may set the lower limit of the ROT (Rate Of Turn) at which the heading line on target symbols will point in direction of turning of the vessel. 1. Roll the trackball to choose the MENU box and then push the left button. 2. Roll the wheel to choose 4 ARP•AIS and then push the wheel or the left button. 3. Roll the wheel to choose 6 [AIS SYMBOL] and then push the wheel or the left button.
4. AIS OPERATION 4.12 Fusion of ARP and AIS Targets An AIS-equipped ship is usually displayed by two symbols on the radar display. This is because the AIS ship position is measured by a GPS navigator (L/L) on that ship whereas the radar detects the same ship by PPI principle (range and bearing relative to own ship radar antenna). To avoid the presentation of two target symbols for the same physical target, the “fusion” function is incorporated.
4. AIS OPERATION When the fusion criteria is met, the ARP symbol is erased and only the AIS symbol is displayed. Further, “ARPA FUSION” appears at the bottom right corner of the display at the time of conversion and the ARP target no. appears next to the AIS symbol. An ARP target whose speed is less than 1 kt is converted to an AIS target if it meets all criteria other than course.
4. AIS OPERATION 4.13 Own Ship’s Data Own ship’s static data (type of ship, call sign, name and position of internal and external GPS antennas) can be viewed as follows 1. Roll the trackball to choose the AIS DISP box at the right side of the screen. 2. Push the right button to open the AIS TARGET menu. 3. Roll the wheel to choose 7 STATIC DATA and then push the wheel or the left button.
4. AIS OPERATION 4.14 Messages You may transmit and receive messages via the VHF link, to a specified destination (MMSI) or all ships in the area. Messages can be sent to warn of safety of navigation, for example, an iceberg sighted. Routine messages are also permitted. Short safety related messages are only an additional means to broadcast safety information. They do not remove the requirements of the GMDSS. 4.14.1 Creating, saving a message This section shows you how to create and save a message.
4. AIS OPERATION 10. Roll the wheel to choose the channel to transmit your message over: A, B, A or B, or A and B. Push the wheel after making your selection. 11. Roll the wheel to choose 8 EDIT and push the wheel or left button. A mini keyboard at the bottom of the menu to enter your message. Mini keyboard 12. Roll the trackball to choose character desired and then push the wheel. Repeat to enter message.
4. AIS OPERATION 4.14.3 Viewing AIS messages When an AIS message is received, the display shows an appropriate icon to alert you. If you are set up to automatically display AIS messages they are automatically displayed upon receipt. The system stores up to 20 AIS messages. When the storage capacity is reached the oldest AIS message is automatically erased to make room for the latest. Note that received messages and alarm messages are not backed up when the power is turned off.
4. AIS OPERATION NAME: FURUNO CALL: 112233 STORM WARNING VICINITY OF 35°N 135°W Example of received AIS message (max. 180 characters) 5. Press the right button several times to close the message and the menu. Automatically displaying AIS messages You can display AIS messages upon receipt as follows: 1. Roll the trackball to choose the AIS DISP box at the right side of the display. 2. Push the right button to open the AIS TARGET menu. 3.
4. AIS OPERATION 4.15 AIS System Messages AIS system messages are displayed at the bottom right corner of the screen. The table below shows the AIS system messages and their meanings. AIS system messages Message ARPA FUSION COLLISION TARGET-FULL LOST RECEIVE GUARD CPA/TCPA AIS ALARM Meaning ARPA target merged with AIS target. The indication disappears when the target no longer meets the criteria set in paragraph 4.12. When the message “RECEIVE” is displayed, ARPA FUSION is not displayed.
4. AIS OPERATION (This page intentionally left blank.
5. VIDEO PLOTTER OPERATION 5.1 General The video plotter • Plots own and other ships’ tracks. (Plotting of other ships’ tracks not available on IMO type.) • Enters waypoints nav lines and marks • Records data onto memory cards (optional card interface required). • It uses two types of memory cards, a memory card (RAM card) for storing own ship and other ship’s tracks and marks, and a digital chart card (ROM card). • 30 nav lines may be stored and each line may contain up to 30 waypoints.
5. VIDEO PLOTTER OPERATION Sample video plotter display North marker Separation zone 340 350 000 010 030 320 Target being tracked Heading marker 020 330 040 310 Waypoint 050 W012 Navline 060 300 070 290 280 AIS activated target Own ship safe contour Heading line 080 090 270 260 100 250 Planned route Own ship vector 110 240 120 W011 230 Dangerous side of own ship safe contour may be marked like this (hatched line).
5. VIDEO PLOTTER OPERATION 5.4 Radar Map A radar map is a combination of map lines and symbols whereby the user can define and input the navigation data, route planning and monitoring data. The radar map may contain 20,000 points of data. The map data can be memorized to facilitate repeated use on a routine navigation area. The user can create a radar map on-real time while using the radar for navigation or at leisure time at anchor or while the radar is not being used.
5. VIDEO PLOTTER OPERATION 5.4.2 Inscribing radar map marks and lines 1. Roll the trackball to choose the MARK box at the left side of the display. MARK > Mark type -> + MARK box 2. Push the right button to open the MARK menu. [MARK MENU] 1 ORIGIN MARK STAB GND/SEA 2 MARK KIND ORIGIN MARK(No. )/ ORIGIN MARK(SYM)/ MAP MARK/ WP 1~50/ WP 51~ 100/ WP 101~150/ WP 151~ 200/ OWN SHIP SHAPE 8 MARK POSN CURSOR/OS/L/L 00°000.00 N 000°000.
5. VIDEO PLOTTER OPERATION • To continue entering the same mark or line (with the guidance box showing “MARK / EXIT”), roll the trackball to choose location and then push the left button. • To quit entering marks or lines, push the right button when the guidance box reads “MARK / EXIT.
5. VIDEO PLOTTER OPERATION 5.5 Erasing Radar Map Marks and Lines A total of 3,000 points is allotted for radar map marks and lines. When this amount is exceeded, no more map marks or lines may be entered unless you erase unnecessary marks or lines. 5.5.1 Erasing individual radar map marks and lines 1. With the cursor inside the effective display area, roll the wheel to show “MARK DELETE / EXIT” in the guidance box. 2.
5. VIDEO PLOTTER OPERATION 5.5.2 Erasing all radar map marks and lines You can erase all radar map marks and lines from the screen as below. Be absolutely sure you want to erase all map marks and lines – erased marks and lines cannot be restored. 1. Roll the trackball to choose the MENU box at the right side of the screen and then push the left button. 2. Roll the wheel to choose 5 PLOTTER and then push the wheel or the left button. 3.
5. VIDEO PLOTTER OPERATION 5.6 Radar Map Corrections 5.6.1 Radar map correction When there is positional error between the radar screen and radar map marks and lines, do the following to correct it. 1. With the cursor inside the effective display area, roll the wheel to display “CHART ALIGN L=OFF / EXIT” in the guidance box. 2. Operate the trackball to align the radar map with the radar screen. 3. Push the left button to set. “MAN ALIGNED” appears at the right side of the screen.
5. VIDEO PLOTTER OPERATION 4. Roll the wheel to choose ON and then push the wheel or the left button. “ALIGN” appears (in red) next to cursor position in the text area. (To remove the correction, choose OFF. If you are using the AIS function, choose ON.) 5. Push the right button twice to close the menu. 5.7 Chart Cards (B, C and W types) FURUNO or NAVIONICS charts may be overlaid on the radar image of the B, C and W type radars when they are interfaced with the optional Card I/F Unit CU-200.
5. VIDEO PLOTTER OPERATION 5.7.2 Chart position correction There may be a case where the chart overlay is not aligned with the radar image. This is due to an error in the position fixing system (GPS, Loran, etc.) or the different coordinates between the position fixing system and the radar. In this case, align the chart with the radar image as below. 1. With the cursor inside the effective display area, roll the wheel to display “CHART ALIGN L=OFF / EXIT” in the guidance box. 2.
5. VIDEO PLOTTER OPERATION 4. Roll the wheel to choose ON and then push the wheel or the left button. “ALIGN” appears (in red) next to cursor position in the cursor data box. (To remove the correction, choose OFF. If you are using the AIS function, choose ON.) 5. Push the right button twice to close the menu. 5.7.4 Chart land color You may choose the color for the land on charts as follows: 1. Roll the trackball to choose the MENU box at the right side of the screen and then push the left button. 2.
5. VIDEO PLOTTER OPERATION 5.8 Hiding/Showing Graphics on the Video Plotter Display 1. Roll the trackball to choose the MENU box at the right side of the screen and then push the left button. 2. Roll the wheel to choose 5 PLOTTER and then push the wheel or the left button. 3. Roll the wheel to choose 9 [DISPLAY] and then push the wheel or the left button. Roll the wheel to choose an item and then push the wheel or the left button. To go to page 2, choose 0 NEXT and then push the wheel or the left button.
5. VIDEO PLOTTER OPERATION 5.9 Track 5.9.1 Plotting own ship’s track A total of 6,000 points are allotted for storage of own ship’s track, marks and lines. When this memory becomes full, the oldest track is deleted to make room for the latest. For that reason you may want to adjust the recording interval to conserve the memory. The table below shows the relation between plotting interval and maximum track recording time. Own track plotting interval and storage time Interval 10 s 30 s 1 min Max.
5. VIDEO PLOTTER OPERATION 5.9.2 Plotting other ships’ track (A, B, C and W types) The tracks of 15 targets (other ships) can be recorded. The memory capacity for other ships’ track is 15,000 points (1,000 points per each of 15 targets). When the other ships’ track memory becomes full the oldest track is deleted to make room for the latest. For that reason you may want to adjust the recording interval to conserve the memory.
5. VIDEO PLOTTER OPERATION 5.9.4 Erasing track The display may become full of track when, for example, own ship traces the same route several times or there are many tracks from other ships. You may erase track two ways: through the menu (by color or percentage) or directly on the screen (track between specified points is erased). Erasing track through the menu 1. Roll the trackball to choose the MENU box at the right side of the screen and then push the left button. 2.
5. VIDEO PLOTTER OPERATION 5.10 Marks and Lines You can inscribe marks on the display to denote important points, for example, a buoy or a wreck. The memory for marks, lines and own ship’s track is 6,000 points. 5.10.1 Inscribing marks and lines 1. Roll the trackball to choose the MARK box at the left side of the screen. MARK > Mark type -> + 162.5°T 11.7NM Bearing and range from own ship to mark Mark box 2. Push the right button to open the MARK menu.
5. VIDEO PLOTTER OPERATION 6. With the MARK box selected, roll the wheel to choose mark desired and then push the left button. See the list on page 5-5 for available marks. 7. Push the left button again. The cursor jumps into the effective display area and the guidance box reads “MARK / EXIT.” 8. Roll the trackball to place the cursor where you want to inscribe a mark and then push the left button to inscribe the mark.
5. VIDEO PLOTTER OPERATION 5.11 Erasing Marks and Lines Up to 6,000 points of own ship’s track, marks and lines may be entered. When this amount is exceeded no more marks or lines can be entered unless unnecessary marks, lines or track are erased. 5.11.1 Erasing individual marks/lines 1. With the cursor inside the effective display area, roll the wheel to show “MARK DELETE / EXIT” in the guidance box. 2. Roll the trackball to place the cursor on the mark or line you wish to erase.
5. VIDEO PLOTTER OPERATION 5.11.2 Erasing all marks and lines To erase all plotter marks and lines from the memory, follow the procedure below. 1. Roll the trackball to choose the MENU box at the right side of the screen and then push the left button. 2. Roll the wheel to choose 5 PLOTTER and then push the wheel or the left button. 3. Roll the wheel to choose 8 [DATA ERASE] and then push the wheel or the left button.
5. VIDEO PLOTTER OPERATION 5.12 Waypoints A particular location is known as a “waypoint,” whether it be a starting point, a destination point or an intermediate point on a voyage. This unit can store 200 waypoints, numbered 001 to 200. Waypoints may be entered with the cursor or by input of latitude and longitude. 5.12.1 Entering waypoints Entering waypoints with the cursor 1. Roll the trackball to choose the MARK box at the left side of the screen. MARK > Mark type last selected, mark number 1 162.
5. VIDEO PLOTTER OPERATION 6. With the MARK box selected, roll the wheel to display waypoint number desired and then push the left button. The cursor jumps into the effective display area and the guidance box reads “MARK / EXIT.” 7. Roll the trackball to place the cursor where you want to inscribe a waypoint mark and then push the left button to inscribe the mark. The waypoint mark (“ ” + waypoint number) appears at the location selected.
5. VIDEO PLOTTER OPERATION 3. Roll the wheel to choose 6 [WPT SET] and then push the wheel or the left button. [WPT SET] 1 BACK 2 WPT NO. SELECT 000 3 WPT NAME 4 WPT L/L 00°00.000 N 000°00.000 E 5 CLEAR DATA WPT SET menu 4. Roll the wheel to choose 2 WPT NO. SELECT and then push the wheel or the left button. 5. Use the wheel to choose waypoint number: Roll the wheel to choose location and then push the wheel to set. 6. To enter waypoint name, follow the procedure below.
5. VIDEO PLOTTER OPERATION 5.12.2 Editing, erasing waypoints from the menu You may edit or erase waypoints from the menu as follows: 1. Roll the trackball to choose the MENU box at the right side of the screen and then push the left button. 2. Roll the wheel to choose 8 [NAV LINE•WPT] and then push the wheel or the left button. 3. Roll the wheel to choose 6 [WPT SET] and then push the wheel or the left button. [WPT SET] 1 BACK 2 WPT NO. SELECT 000 3 WPT NAME 4 WPT L/L 00°00.000 N 000°00.
5. VIDEO PLOTTER OPERATION 5.12.3 Erasing waypoints Waypoints may be erased individually or collectively. Note that a waypoint cannot be erased if it is part of a nav line. Erasing individual waypoints 1. With the cursor inside the effective display area, roll the wheel to display “MARK DELETE / EXIT” in the guidance box. 2. Roll the trackball to place the cursor on the waypoint you wish to erase. A flashing “+” appears on the mark when it is correctly selected. 3.
5. VIDEO PLOTTER OPERATION 5.12.4 Waypoint list The waypoint list stores position data of all registered waypoints. Each page of the waypoint list holds eight waypoints. To display the waypoint list: 1. Roll the trackball to choose the MENU box at the right side of the screen. 2. Roll the wheel to choose 8 NAV LINE•WPT and then push the wheel or the left button. 3. Roll the wheel to choose 7 [WPT LIST] and then push the wheel or the left button. Asterisks indicate no data.
5. VIDEO PLOTTER OPERATION 5.12.5 Displaying waypoint name and number You may turn waypoint name and number display on or off as desired. 1. Roll the trackball to choose the MENU box at the right side of the screen and then push the left button. 2. Roll the wheel to choose 8 [NAV LINE•WPT] and then push the wheel or the left button. 3. Roll the wheel to choose 0 NEXT and then push the wheel or the left button.
5. VIDEO PLOTTER OPERATION 5.13 Nav Lines 30 nav lines may be entered, and each line may have up to 30 waypoints. 5.13.1 Entering new nav line To enter a nav line, first enter appropriate waypoints. Then, do the following: 1. Roll the trackball to choose the MENU box and then push the left button. 2. Roll the wheel to choose 8 [NAV LINE•WPT] and then push the wheel or the left button. 3. Roll the wheel to choose 8 [NAV LINE SET] and then push the wheel or the left button.
5. VIDEO PLOTTER OPERATION 5.13.2 Editing nav lines Follow the procedure below to edit a nav line. Before editing a nav line it must be disabled. See paragraph 5.13.6. 1. Roll the trackball to choose the MENU box and then push the left button. 2. Roll the wheel to choose 8 [NAV LINE•WPT] and then push the wheel or the left button. 3. Roll the wheel to choose 8 [NAV LINE SET] and then push the wheel or the left button. 4. Roll the wheel to choose 2 NAV LINE NO.
5. VIDEO PLOTTER OPERATION 5.13.3 Nav line list The nav line list, which shows all nav lines registered, may be displayed as follows: 1. Roll the trackball to choose the MENU box and then push the left button. 2. Roll the wheel to choose 8 [NAV LINE•WPT] and then push the wheel or the left button. 3. Roll the wheel to choose 9 [NAV LINE LIST] and then push the wheel or the left button.
5. VIDEO PLOTTER OPERATION 5.13.4 Erasing nav lines 30 nav lines may be entered. You may erase unnecessary nav lines as shown below. A nav line which is currently in use cannot be erased. Erasing individual nav lines 1. Roll the trackball to choose the MENU box at the right side of the screen and then push the left button. 2. Roll the wheel to choose 8 [NAV LINE•WPT] and then push the wheel or the left button. 3. Roll the wheel to choose 8 [NAV LINE SET] and then push the wheel or the left button.
5. VIDEO PLOTTER OPERATION Erasing all nav lines 1. Roll the trackball to choose the MENU box and then push the left button. 2. Roll the wheel to choose 5 PLOTTER and then push the wheel. 3. Roll the wheel to choose 8 [DATA ERASE] and then push the wheel.
5. VIDEO PLOTTER OPERATION 7. If you want to be alerted when own ship nears a waypoint by a preset distance, choose 0 NEXT and then push the wheel. [NAV LINE•WPT (2/2)] 1 BACK 2 ARRIVAL WPT ALARM OFF/ON 3 TURNING LINE OFF/ON/REVISED 4 DISP WPT NO. OFF/ON 5 DISP WPT NAME OFF/ON NAV LINE•WPT menu (2/2) 8. Use the wheel to choose ARRIVAL WPT ALARM and then push the wheel. 9. Choose ON and then push the wheel. 10. Roll the wheel to choose 3 TURNING LINE and then push the wheel or the left button. 11.
5. VIDEO PLOTTER OPERATION 5.13.6 Displaying nav line, waypoint mark Displaying internal nav lines 1. Roll the trackball to choose the MENU box and then push the left button. 2. Roll the wheel to choose 8 [NAV LINE•WPT] and then push the wheel or the left button. 3. Roll the wheel to choose 2 NAV LINE DATA and then push the wheel or the left button. 4. Roll the wheel to choose INTERNAL DATA and then push the wheel or the left button. 5.
5. VIDEO PLOTTER OPERATION Waypoint mark (B, C and W types only) The waypoint mark shows the location of a destination waypoint which is set on a navigator. You may mark this location on the radar display by following the procedure shown below. 330 340 350 000 010 020 030 320 Waypoint Mark 040 310 050 060 300 070 290 280 080 270 090 260 100 250 110 240 120 230 130 140 220 210 200 190 180 170 160 150 Waypoint mark 1.
5. VIDEO PLOTTER OPERATION 5.14 Recording Data The optional Card I/F Unit CU-200 is required to record or replay data. The CU-200 has two card slots and you can connect two units, for a total of four card slots. 5.14.1 Initializing memory (RAM) cards Before you can use a memory (RAM) card it must be initialized. Formatting prepares the recording surface of the card for use with the system, and deletes all data recorded in the memory card.
5. VIDEO PLOTTER OPERATION 6. Roll the wheel to choose 0 NEXT and then push the wheel or the left button. [CARD (2/2)] 1 BACK 2 [FILE DELETE] 3 [CARD INITIALIZE] CARD menu, page 2 7. Roll the wheel to choose 3 CARD INITIALIZE and then push the wheel or the left button. [CARD INITIALIZE] 1 BACK 2 INITIALIZE START CARD INITIALIZE menu 8. Roll the wheel to choose 2 INITIALIZE START and then push the wheel or the left button to initialize the card.
5. VIDEO PLOTTER OPERATION 4. Roll the wheel to choose DRIVE SELECT and then push the wheel or the left button. 5. Roll the wheel to choose appropriate drive and then push the wheel or the left button. 6. Roll the wheel to choose data to record (one item among 4-9) and then push the wheel or the left button. For example choose 4 WR MARK and then push the wheel or the left button. The display then looks something like the one below. [WR MARK] 1 BACK 2 NAME (See note below.
5. VIDEO PLOTTER OPERATION 5.15 Replaying Data Video plotter data (track, marks, etc.) may be replayed on the screen. This is useful for analyzing past data. 1. Insert memory card into the appropriate slot in an I/F card unit. 2. Roll the trackball to choose the MENU box and then push the left button. 3. Roll the wheel to choose 6 [CARD] and then push the wheel or the left button.
5. VIDEO PLOTTER OPERATION Note: Marks, own ship’s track and other ships’ tracks replayed from a memory card are added to the data currently displayed. If, at replay, the memory is full, the message “MEMORY FULL” appears. Press the [ALARM ACK] key to erase the message. Memory capacity is as shown below. Mark: 20,000 points Own ship’s track: 20,000 points Other ships’ tracks: 20,000 points 5.16 Deleting Files 1. Roll the trackball to choose the MENU box and then push the left button. 2.
5. VIDEO PLOTTER OPERATION (This page intentionally left blank.
6. MAINTENANCE, TROUBLESHOOTING Periodic checks and maintenance are important for proper operation of any electronic system. This chapter contains maintenance and troubleshooting instructions to be followed to obtain optimum performance and the longest possible life of the equipment. Before attempting any maintenance or troubleshooting procedure please review the safety information below. WARNING Do not open the equipment. Hazardous voltage which can cause electrical shock exists inside the equipment.
6. MAINTENANCE, TROUBLESHOOTING 6.1 Periodic Maintenance Schedule Regular maintenance is essential to good performance. A regular maintenance program should be established and should at least include the items shown in the table below. Maintenance schedule Interval When needed Check point Check and measures Remarks The LCD will in time accumulate a layer of dust which tends to dim the picture Wipe the LCD carefully to prevent scratching, using tissue paper and an LCD cleaner.
6. MAINTENANCE, TROUBLESHOOTING 6.
6. MAINTENANCE, TROUBLESHOOTING 6.4 Replacement of Battery on GC Board The battery installed on the GC (GyroCompass) Board inside the processor unit preserves gyro data when the power is turned off. The life of the battery is about five years. When the battery voltage is low, NG appears at the diagnostic test for the GC Board. When this occurs, contact your dealer for replacement. Battery on GC Board Battery type GC board 6.5 CR 1/2 8.
6. MAINTENANCE, TROUBLESHOOTING 6.6 Easy Troubleshooting This paragraph provides troubleshooting procedures which the user may follow to restore normal operation. If you cannot restore normal operation, do not attempt to check inside any unit. Any repair work is best left to a qualified technician. Easy troubleshooting procedures Problem Key beep inaudible Cause Remedy Key beep turned off Adjust key beep level on the OPERATION menu, referring to paragraph 1.42.
6. MAINTENANCE, TROUBLESHOOTING 6.7 Advanced-level Troubleshooting This paragraph describes how to cure hardware and software troubles which should be carried out by qualified service personnel. Note: This radar equipment contains complex modules in which fault diagnosis and repair down to component level are not practicable by users. Advanced troubleshooting Problem Probable causes or check Remedy points Power turned on but radar 1) Blown fuse.
6. MAINTENANCE, TROUBLESHOOTING Advanced troubleshooting (con’t) Problem Probable causes or check Remedy points Marks, indications and noise appear but no echo (Transmission leak representing own ship position is absent) 1) TX fuse 1) If fuse is blown, replace it. If it blows again, the modulator or associated circuit may be defective. 2) Magnetron 2) Check magnetron current. Replace magnetron. 3) Modulator board 3) Replace modulator board. 4) SPU board 4) Replace SPU board.
6. MAINTENANCE, TROUBLESHOOTING Advanced troubleshooting (con’t) Problem Probable causes or check Remedy points Interference rejector is inoperative (interference rejection level not displayed) SPU board Replace SPU board. Echo stretch is ineffective SPU board (neither ES1, ES2 nor ES3 is displayed) Replace SPU board. Range rings are not displayed 1) Adjust the brilliance of range rings on the BRILL menu to see if intensity is increased 1) Replace associated circuit board if unsuccessful.
6. MAINTENANCE, TROUBLESHOOTING 6.8 Diagnostics A diagnostic test program is provided to test major circuit boards in the control unit, processor unit and card I/F unit. Note that the normal radar picture is lost during this test. Proceed as follows to execute the diagnostic test: 1. Roll the trackball to choose the MENU box and then push the left button. 2. Roll the wheel to choose 9 [CUSTOMIZE•TEST] and then push the wheel or the left button.
6. MAINTENANCE, TROUBLESHOOTING PROGRAM No. SPU 0359204-02.** RFC 0359202-01.** KEY 0359203-01.** REMOTE1 0359203-01.** REMOTE2 # CARD 0359209-01.** ROM OK OK OK OK RAM OK OK OK OK DIP SW 0000 OK OK 0000 PROCESSOR UNIT MONITOR -12V -11.6 3.3V 3.3 5V 4.9 12V 11.6 SCANNER MOTOR 20.7 RF UNIT MONITOR TEMPERATURE TUNE IND HV R. MONITOR MAG. CURRENT HEATER 12V -12V 5V 32V TUNE OUT TRIGGER FREQ ANT SPEED 0 0 0 0 0 0 27.3 1.4 527.9 1.6 1.5 1.8 11.9 -11.8 4.8 31.8 19.2 2273 21.
6. MAINTENANCE, TROUBLESHOOTING 7. Press the [F1] key to change the display. The buzzer stops and the screen shows the sentences being input to the radar, under the categories of GPS1 and GPS2 (position), speed, heading and nav data. Below is an example. (The sentences shown depend on your system settings.) GGA GLL RMC RMB VTG ZDA DTM BWR BWC GGA GLL RMC RMB VTG ZDA DTM BWR BWC VBW VHW VDR HDT
6. MAINTENANCE, TROUBLESHOOTING 6.9 System Messages This sections provides all the error messages which may appear on the display screen.
6.
6. MAINTENANCE, TROUBLESHOOTING (This page intentionally left blank.
APPENDIX 1.
APPENDIX (Continued from previous page) 4 ARPzAIS 1 BACK 2 GUARD ZONE STAB (STAB HDG, STAB NORTH) 3 GUARD POLYGON (OFF, STAB GND, STAB HDG, STAB NORTH) 4 [TRIAL MANEUVER] 1 BACK 2 TRIAL (OFF, STATIC, DYNAMIC) 3 TRIAL SPEED RATE (0-99 kt, 0.00-9.99 kt/s, two sets) 4 TRIAL TURN RATE (0-99 kt, 0.00-99.
APPENDIX (Continued from previous page) 9 [DISPLAY] 1 BACK 2 GRID (OFF, L/L, GYOKU) 3 OWN TRACK (OFF, ON) 4 TARGET TRACK (OFF, ON)* 5 MARK (OFF, ON) 6 LAND DENSITY (OFF, ON)* 7 PLACE NAME (OFF, ON)* 8 COAST LINE (OFF, ON) 9 CONTOUR LINE (OFF, ON, DEPTH) 1 BACK 0 NEXT 2 NAV LINE(MAP) (OFF, ON) 3 DANGER HIGHLIGHT (OFF, ON) 4 PROHIBITED AREA (OFF, ON) 5 BUOY (OFF, ON) 0 AUTO TARGET TRACK (OFF, ON)* 6 CARD 1 BACK 2 DRIVE SELECT 3 READ CARD 4 WR MARK 5 WR NAV LINEQWPT 6 WR OWN TRACK 7 WR TARGET TRACK* 8 WR SE
APPENDIX (Continued from previous page) 7 [WPT LIST] 8 [NAV LINE SET] 9 [NAV LINE LIST] 0 NEXT 9 CUSTOMIZEz TEST 1 BACK 2 [DATA BOX] 1 BACK 2 NAV LINE NO. SELECT 3 NAV LINE NAME 4 [NAV LINE ENTRY] 5 CLEAR DATA 1 BACK 2 ARRIVAL WPT ALARM (OFF, ON(0.00-9.99 nm)) 3 TURNING LINE (OFF, ON, REVISED) 4 DISP WPT NO.
APPENDIX (Continued from previous page) 6 [PICTURE] 7 [OPERATION] 1 BACK 2 (PICTURE1, PICTURE 2, PICTURE 3, PICTURE 4, NEAR, FAR, NEAR BUOY, FAR BUOY, ROUGH SEA, SHIP, 1 1 2 2 HARBOR* , COAST* , NEAR BIRD* , FAR BIRD* ) 1 BACK 2 WHEEL DRIVE (NORMAL, REVERSE) 3 KEY BEEP (OFF, LO, MID, HI) 4 REMOTE KEY (F*-KEY, DISPLAY SELECT) 3 5 POPUP GUIDANCE (OFF, ON)* 6 OWN SHIP VECTOR (OFF, HDG, COURSE) 3 7 STERN-UP (OFF, ON)* 8 SHUTTLE FERRY (OFF, MODE1, MODE2) 9 DUAL RADAR 1 BACK 0 NEXT 8 [TEST] 2 DUAL RADAR (OFF
APPENDIX Pop-up menus of on-screen boxes [HDG MENU] 1 HDG SOURCE AD-10/SERIAL 2 GC-10 SETTING 000.0° HDG menu [SPD MENU] 11 SHIP SPEED LOG(BT)/LOG(WT)/ GPS/MANUAL/REF 22 MANUAL SPEED 0.0kt 33 SET DRIFT OFF/ON SPEED menu [CURSOR MENU] 2 ↓ TARGET DATA & ACQ/ TARGET CANCEL/ ARP TGT DATA & ACQ/ TARGET TRACK ON*3/ TARGET TRACK OFF*3/ REF MARK/ EBL OFFSET/ OFFCENTER/ ZOOM/ MARK DELETE/ CHART ALIGN/ 8 ↑ CURSOR menu [OS POSN MENU] 1 NAV AID GPS1/GPS2/ DEAD RECKONING/ LAN/INS 2 MANUAL L/L 00°00.000 N 000°00.
APPENDIX [BRILL1 MENU (1/2)] 1 ECHO COLOR YEL/GRN/ WHT/COLOR* 2 BKGD COLOR BLK-GRN/ BLK-RED/ BLU-CIR/ BLU/BRT-BLU 3 PANEL DIMMER 4 CHARACTER 5 CURSOR 6 ECHO 7 TRAIL 8 HL 9 RING 0 NEXT [BRILL1 MENU (2/2)] 1 2 3 4 5 6 7 8 9 0 BACK BEARING CURSOR EBL VRM INDEX LINE ARP SYMBOL AIS SYMBOL L/L GRID MARK CHART* BRILL menu, page 2 BRILL menu, page 1 [PICTURE MENU] 1 INT REJECT OFF/1/2/3 2 ECHO STRETCH OFF/1/2/3 3 ECHO AVERAGE OFF/1/2/3 4 NOISE REJ OFF/ON 5 AUTO STC OFF/ON 6 AUTO RAIN OFF/ON 7 VIDEO CONTRAST 1/
APPENDIX 2. Digital Interface Input sentences (RP Board, J4) BWC*, BWR*, DBS, DBT, DPT, DTM, GGA, GLC, GLL, HDT, MTW, MWV, RMA, RMB, RMC, RTE VBW, VDR, VHW, VTG, VWR, VWT, WPL, ZDA, !AIVDM, !AIVDO, $AIALR Output sentences OSD, TLL*, TTM, RSD *: Not available on IMO radar Data reception Data is received in serial asynchronous form in accordance with the standard referenced in IEC 61162-2. The following parameters are used: Baud rate: 38,400 bps: HDT, !AIVDM, !AIVDO and $AIALR.
APPENDIX BWR - Bearing and distance to waypoint - rhumb line (Not available on IMO radar) $--BWR,hhmmss.ss,llll.lll,a,yyyyy.yyy,a,x.x,T,x.x,M,x.
APPENDIX DTM - Datum reference $--DTM,ccc,a,x.x,a,x.x,a,x.x,ccc*hh | | | | | | | | | | | | | | | | | +--- 7 | | | | | | | +------ 6 | | | | | | +---------- 5 | | | | +--+------------- 4 | | +---+------------------- 3 | +------------------------- 2 +---------------------------- 1 1. Local datum W84 - WGS84 W72 - WGS72 S85 - SGS85 P90 - PE90 999 - User defined IHO datum code 2. Local datum subdivision code 3. Lat offset, min, N/S 4. Lon offset, min, E/W 5. Altitude offset, m 6.
APPENDIX DBT - Depth below transducer $--DBT,x.x,f,x.x,M,x.x,F*hh | | | | | | | | | | | | | +--------- 4 | | | | +--+----------- 3 | | +--+----------------- 2 +--+----------------------- 1 1. Water depth, feet 2. Water depth, m 3. Water depth, fathoms 4. Checksum DPT - Depth $--DPT,x.x,x.x,x.x*hh | | | | | | | +----- 4 | | +--------- 3 | +------------ 2 +---------------- 1 1. Water depth relative to trancsducer, in meters 2. Offset from transeducer, in meters(see notes 1 and 2) 3.
APPENDIX GGA - Global positioning system fix data $--GGA,hhmmss.ss,llll.lll,a,yyyyy.yyy,a,x,xx,x.x,x.x,M,x.x,M,x.
APPENDIX GLL - Geographic position, latitude/longitude $--GLL,llll.lll,a,yyyyy.yyy,a,hhmmss.ss,A,a*hh | | | | | | | | | | | | | | | +------- 6 | | | | | | +--------- 5 | | | | | +----------- 4 | | | | +---------------- 3 | | +------+----------------------- 2 +---+----------------------------------- 1 1. Latitude, N/S 2. Longitude, E/W 3. UTC of position 4. Status: A=data valid, V=data invalid 5. Mode indicator(see note) 6.
APPENDIX HDT - Heading, true $--HDT,x.x,T*hh | | | | | +--------- 2 +----+----------- 1 1. Heading, degrees true 2. Checksum MTW - Water temperature $--MTW,x.x,C*hh | | | | | +--------- 2 +--+----------- 1 1. Temperature, degrees C 2. Checksum MWV - Wind speed and angle $--MWV,x.x,a,x.x,a,A*hh | | | | | | | | | | | +--------- 6 | | | | +----------- 5 | | | +------------- 4 | | +---------------- 3 | +------------------- 2 +---------------------- 1 1.
APPENDIX RMB - Recommended minimum navigation information $--RMB,A,x.x,a,c--c,c--c,llll.lll,a,yyyyy.yyy,a,x.x,x.x,x.
APPENDIX RMC - Recommended minimum specific GPS/TRANSIT data $--RMC,hhmmss.ss,A,llll.lll,a,yyyyy.yyy,a,x.x,x.x,xxxxxx,x.
APPENDIX RTE - Route $--RTE,x.x,x.x,a,c--c,c--c,.....,c--c*hh | | | | | | | | | | | | | +--------- 7 | | | | | +------------ 6 | | | | +----------------------- 5 | | | +---------------------------- 4 | | +-------------------------------- 3 | +----------------------------------- 2 +--------------------------------------- 1 1. Total number of messages being transmitted 2. Message number 3.
APPENDIX VHW - Water speed and heading $--VHW,x.x,T,x.x,M,x.x,N,x.x,K*hh | | | | | | | | | | | | | | | | | +--------- 5 | | | | | | +--+----------- 4 | | | | +--+----------------- 3 | | +---+----------------------- 2 +---+----------------------------- 1 1. Heading, degrees true 2. Heading, degrees magnetic 3. Speed, knots 4. Speed, km/h 5. Checksum VDR - Set and drift $--VDR,x.x,T,x.x,M,x.
APPENDIX VTG - Course over ground and ground speed $--VTG,x.x,T,x.x,M,x.x,N,x.x,K,a*hh | | | | | | | | | | | | | | | | | | | +------- 6 | | | | | | | | +--------- 5 | | | | | | +--+----------- 4 | | | | +--+----------------- 3 | | +--+----------------------- 2 +--+----------------------------- 1 1. Course over ground, degrees true 2. Course over ground, degrees magnetic 3. Speed over ground, knots 4. Speed over ground, km/h 5. Mode indicator(see note) 6.
APPENDIX VWT - True wind speed and angle $--VWT,x.x,a,x.x,N,x.x,M,x.x,K*hh | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | +----------------------- 5 | | | | | +---+------------------------- 4 | | | +---+--------------------------------- 3 | +--+---------------------------------------------- 2 +------------------------------------------------------ 1 1.
APPENDIX $AIALR - Set alarm state $AIALR,hhmmss.ss,xxx,A,A,c--c*hh | | | | | | | | | | | +----------------- 6 | | | | +----------------- 5 | | | +-------------------- 4 | | +---------------------- 3 | +------------------------- 2 +--------------------------------- 1 1. Time of alarm condition change, UTC 2. Local alarm number(identifier) 3. Alarm condition(A=threshold exceeded, V=not exceeded) 4. Alarm’s acknowledge state, A=acknowledged V=unacknowledged 5. Alarm’s description text 6.
APPENDIX !AIVDO - UAIS VHF Data-link Own-vessel report !AIVDO,x,x,x,a,s--s,x*hh | | || | | | | | | | | | +--- 7 | | | | | +----- 6 | | | | +-------- 5 | | | +------------ 4 | | +-------------- 3 | +---------------- 2 +------------------ 1 1. Total number of sentences needed to transfer the message, 1 to 9 2. Message sentence number, 1 to 9 3. Sequential message identifier, 0 to 9 4. AIS channel Number 5. Encapsulated ITU-R M.1371 radio message* 6. Number of fill-bits, 0 to 5 7.
APPENDIX Output sentences OSD- Own ship data $--OSD,x.x,A,x.x,a,x.x,a,x.x,x.x,a*hh | | | | | | | | | | | | | | | | | | | +--------- 10 | | | | | | | | +----------- 9 | | | | | | | +-------------- 8 | | | | | | +------------------ 7 | | | | | +--------------------- 6 | | | | +------------------------ 5 | | | +--------------------------- 4 | | +------------------------------ 3 | +--------------------------------- 2 +------------------------------------ 1 1. Heading, degrees true 2.
APPENDIX RSD - Radar system data $RARSD,x.x,x.x,x.x,x.x,x.x,x.x,x.x,x.x,x.x,x.x,x.
APPENDIX TLL - Target latitude and longitude For non-IMO specification radar, this function outputs event mark position. $--TLL,xx,llll.lll,a,yyyyy.yyy,a,c--c,hhmmss.
APPENDIX TTM - Tracked target message $--TTM,xx,x.x,x.x,a,x.x,x.x,a,x.x,x.x,a,c--c,a,a,hhmmss.
APPENDIX Serial interface – input ports Heading sensor Transmission rate is selectable from 4800 bps and 38.4 kbps. Isolated RS485 Transceiver RD-A LTC1535 RD-B GND Logical High: A-B> +0.2V Logical Low: A-B< -0.2V Log/navigator Photo Coupler 470 ohm RD-A PC-400 RD-B This port is an opticoupler used to isolate I/F terminal on RD terminal.
APPENDIX Serial interface – output ports ARPA for ECDIS Dual differrential drivers and receivers RD-A SN751178NS RD-B Logical High: A-B> +0.2V Logical Low: A-B< -0.2V Serial interface – input/output ports Transmission rate is selectable from 4800 bps and 38.4 kbps. Input port (RD-A, B) Isolated RS485 Transceiver RD-A LTC1535 RD-B GND Logical High: A-B> +0.2V Logical Low: A-B< -0.2V Output port (TD-A, B) Isolated RS485 Transceiver TD-A LTC1535 TD-B GND Logical High: A-B> +4.0V Logical Low: A-B> -4.
APPENDIX 3. Parts Lists and Parts Location Parts lists Processor unit RPU-014, Control unit RCU-104/105, Display unit MU-201CR/ MU-231CR FURUNO Model Unit FR-21x7/28x7 Series (incl. BB series) Processor Unit RPU-013 Control Unit RCU-014 Control Unit RCU-015 Display Unit MU-201CR Display Unit MU-231CR ELECTRICAL PARTS LIST 2003/10 SYMBOL PRINTED CIRCUIT BOARD/ ASSY.
APPENDIX Antenna unit RSB-096/097 (for FAR-2117(-BB)/2127(-BB)/2817/2827) FURUNO Model Unit FAR-2117(BB)/2127(BB)/2817(BB)/2827(BB) Antenna Unit RSB-096/097 ELECTRICAL PARTS LIST 2003/10 SYMBOL NAME RF BP MD AP-30 REMARKS PRINTED CIRCUIT BOARD 03P9349 03P9347 03P9244-A 03P9244-B FAR-2117/2817 FAR-2127/2827 SCANNER CHASSIS RSB-096 RSB-097 24 rpm 42 rpm RF MODULE RTR-078 RTR-079 FAR-2117/2817 FAR-2127/2827 MIC ASSEMBLY RU-9601 RU-9603 FAR-2117/2817 FAR-2127/2827 MOTOR D8G-516 D8G-571 24 rp
APPENDIX Antenna unit RSB-103/104/105 (FAR-2827W) FURUNO Model Unit FAR-2827W Antenna Unit RSB-104/105 ELECTRICAL PARTS LIST 2003/10 SYMBOL NAME TB BP GEN REMARKS PRINTED CIRCUIT BOARD 03P9349 03P9347 MOTOR D8G-516 Transceiver unit RTR-081 (FAR-2827W) FURUNO Model Unit FAR-2827W Transceiver Unit RTR-081 ELECTRICAL PARTS LIST 2007/11 SYMBOL NAME TB IF AMP PWR MD RFC REMARKS PRINTED CIRCUIT BOARD 03P9349 03P9335 03P9348 03P9244 03P9346 MIC ASSEMBLY RU-9601 MOTOR 109P0824H602 24 rpm DIODE L
APPENDIX Antenna unit RSB-098/099/100/101/102 (for FAR-2137S-BB)/2837S) FURUNO Model Unit FAR-2137S(BB), FAR-2837S(BB) Antenna Unit RSB-098/099 RSB-100/101/102 ELECTRICAL PARTS LIST 2006/11 SYMBOL NAME TB IF AMP PWR MD RFC MSS MSS REMARKS PRINTED CIRCUIT BOARD 03P9349 03P9335 03P9348 03P9244 03P9346 MSS-7497 MSS-7497A 200/220V, 3φ 380/440V, 3φ SCANNER CHASSIS RSB-098 RSB-099 RSB-100 RSB-101 RSB-102 21/26 rpm 21/26 rpm 45 rpm 45 rpm 45 rpm RF MODULE RTR-080 MIC ASSEMBLY RU-9760A MOTOR RM-7398 R
APPENDIX Power Supply Unit PSU-007 (for FAR-2137S(-BB)/2837S FURUNO Model Unit PSU-007 Power Supply Unit ELECTRICAL PARTS LIST 2003/10 SYMBOL NAME REMARKS PRINTED CIRCUIT BOARD TB1 RELAY HG3_DC12V Antenna unit RSB-104/105 (for FAR-2837SW) FURUNO Model Unit FAR-2837SW Antenna Unit RSB-104/105 ELECTRICAL PARTS LIST 2003/10 SYMBOL NAME TB BP GEN MSS REMARKS PRINTED CIRCUIT BOARD 03P9349 03P9347 MSS-7497 MSS-7497-A MOTOR RM-7398 RM-7345 200/220V, φ3 380/440V, φ3 RSB-104 RSB-104 RSB-105 RSB-10
APPENDIX Transceiver unit RTR-082 (for FAR-2837SW) FURUNO Model Unit FAR-2837SW Transceiver Unit RTR-082 ELECTRICAL PARTS LIST 2006/11 SYMBOL NAME TB IF AMP PWR MD RFC PRINTED CIRCUIT BOARD 03P9349 03P9335 03P9348 03P9244 03P9346 MIC ASSEMBLY RU-9760A MOTOR 109P0824H602 TR LIMITER TL378A CIRCULATOR RC_6584S or RC4910S PULSE TRANSFORMER RT-9273 MAGNETRON MG5223F AP-34 REMARKS
APPENDIX Parts location Display unit MU-231CR (AC specification) Noise Filter (AC spec.: LF-205A DC spec.: MXB-1206-33) FIL Board (03P9360) DVI I/F Board (BSM-501A) DC-DC Board 03P9359 (AC spec.) (For DC spec., PWR Pack RKW-12-13RE is used.
APPENDIX Display unit MU-201CR (DC specification) Noise Filte (AC spec.: LF-205A DC spec.: MXB-1206-33) DIV I/F Board (SCBFNRB-A) PWR Module RKW-12-13RE (DC spec.) (For AC spec, DC-DC Board 03P9359 is used.
APPENDIX Control unit RCU-014 Trackball Assy. (TA4726N) BUZ Board (03P9362) PNL Board (03P9343) Control unit RCU-014, rear cover removed Control unit RCU-015 Trackball Assy.
APPENDIX Transceiver unit RTR-078/079 (for FAR-2117(-BB)/2127(-BB)/2817/2827 Circulator RC-3686 RFC Board (03P9346) RF PWR Board (03P9348) Diode Limiter (RU-9099) MIC Assy.
APPENDIX MD Board (03P9244-B) Pulse Transformer (RT-9203) Magnetron (MG5436) Transceiver unit RTR-079 (for FAR-2117(-BB)/2127(-BB)/2817/2827, lower half Antenna unit RSB-103 (for FAR-2827W) BP Board (03P9347) RF Board (03P9349) Motor (DG8-516) Antenna unit RSB-103 (for FAR-2827W) AP-39
APPENDIX Transceiver unit RTR-081 (for FAR-2827W) Diode Limiter (RU-9099) Isolator (FX0157) MIC Assy.
APPENDIX Antenna unit RSB-098/099/100/101/102 (for FAR-2137S(-BB)/2837S) Behind plate MSS-7497 Board (200/220 V) MSS-7497-A Board (380/440 V) MIC Assy.
APPENDIX Magnetron (MG5223F) RFC Board (03P9346) MD Board (03P9244) Pulse Transformer (RT-9773) Antenna unit RSB-098/099/100/101/102 (for FAR-2137S(-BB)/2837S), cover opened AP-42
APPENDIX Antenna unit RSB-104/105 (for FAR-2837SW) Motor* * RM-7398 (For RSB-104, 21 rpm, 200 V, 3φ, 50 Hz; For RSB-104, 26 rpm, 220 V, 3φ, 60 Hz) RM-7345 (For RSB-105, 21 rpm, 380 V, 3φ, 50 Hz; For RSB-105, 26 rpm, 440 V, 3φ, 60 Hz) TB Board (03P9349) Antenna unit RSB-104/105 (for FAR-2837SW), cover opened MSS Board MSS-7497 (200/220V, φ3) MSS-7497-A (380/440V, φ3) BP GEN Board (03P9347) Antenna unit RSB-104/105 (for FAR-2837SW), cover opened AP-43
APPENDIX Transceiver unit RTR-082 (for FAR-2837SW) MD Board (03P9244) RF PWR Board (03P9348) RFC Board (03P9346) Pulse Transformer (RT-9273) Magnetron (MG5223F) Beneath plate MIC Assy.
APPENDIX 4. Longitude Error Table (on 96 nm range scale) The longitude lines concentrate on the north pole and south pole, namely, 1 nm is equivalent to 1 minute at 0 degree latitude, 2 minutes at 60 degrees latitude, 3 minutes at 70 degrees latitude and so on. For this reason, a longitude error occurs on the radar display. For example, when own ship is at 60°N and 135°E, even if the cursor indication is 62°N and 139°E, the real cursor position is deviated to the left (west) side.
APPENDIX (nm) LAT θ 5° 75° 0.2256 10° 0.4444 15° 0.6496 70° 0.21980213 0.43290201 0.632803 20° 25° 30° 1.1248 35° 0.8350 0.9950 0.8134132 0.96923215 1.09551918 1.1884382 1.2202 40° 1.2786 45° 1.2980 1.24517456 1.26402037 65° 0.21229339 0.41810678 0.61115946 0.78556318 0.93600295 1.05790007 1.14755221 1.20224625 1.22034042 60° 0.20316898 0.40012949 0.58486463 0.75173456 0.89565021 1.0122297 1.09793265 1.15016811 1.16737294 55° 0.19249832 0.37910698 0.55411863 0.71218478 0.
INDEX 2 2nd-trace echo rejector ........................1-71 A A/C RAIN adjustment auto ..................................................1-28 manual .............................................1-29 A/C SEA adjustment automatic .........................................1-27 manual .............................................1-26 method.............................................1-26 A/C SEA box........................................1-26 AIS activating targets ...............................
INDEX ARP ACQ MODE box ........................... 3-3 ARP VECTOR box.............................. 3-18 B Battery replacement ............................. 6-4 Bearing measurement ........................ 1-33 BRILL box ............................................1-11 BRILL control .......................................1-11 Brilliance monitor .............................................1-11 screen data ..................................... 1-72 C Colors..................................................
INDEX MODE key ...........................................1-17 N Nav data ..............................................1-74 Noise rejector ......................................1-70 North marker .......................................1-57 North-up mode ....................................1-19 O OFF CENTER key...............................1-42 Off centering........................................1-42 Origin marks entering............................................1-53 erasing ............................
INDEX V Video plotter chart display ...................................... 5-9 chart land color.................................5-11 chart position correction.................. 5-10 cursor data correction ..............5-8, 5-10 displaying nav lines......................... 5-33 graphics on/off................................. 5-12 initializing memory cards ................ 5-35 line entry.......................................... 5-16 line erasure ..................................... 5-18 mark entry ....
FURUNO ELECTRIC CO., LTD. 9-52 Ashihara-Cho, Nishinomiya City, 662-8580, Hyogo, Japan Tel: +81 798-65-2111 Fax: +81 798-65-4200 Pub No. DOC-921 Declaration of conformity We 0735 FURUNO ELECTRIC CO., LTD.
Configuration matrix of FAR-2XX7 series TR-up TR-down TR-up x x x x x x x x X-band 4 ft XN-20AF x x x x x x x x x x X-band 6.
