Installation Instructions

ManualsBrandsFuruno ManualsVehicleGP-1670F

Installation Manual

GPS PLOTTER/SOUNDER GP-1670F

GP-1870F

SAFETY INSTRUCTIONS ................................................................................................ i

1. MOUNTING .............................................................................................................. 1-1

1.1 Mounting of Display Unit ............................................................................................... 1-1

1.2 Replacement Kit (option) .............................................................................................. 1-2

2. INSTALLATION OF TRANSDUCERS ..................................................................... 2-1

2.1 How to Mount a Transducer through the Unit ............................................................... 2-1

2.2 Transom Mount Transducer .......................................................................................... 2-3

2.3 How to Mount a Transducer inside the Hull .................................................................. 2-4

3. WIRING .................................................................................................................... 3-1

3.1 Display Unit ................................................................................................................... 3-1

3.2 Transducer .................................................................................................................... 3-2

3.3 External Equipment ....................................................................................................... 3-2

PACKING LIST ........................................................................................................... A-1

OUTLINE DRAWINGS ................................................................................................ D-1

INTERCONNECTION DIAGRAMS ............................................................................. S-1

All brand and product names are trademarks, registered trademarks or service marks of their respective holders.

www.furuno.com

Summary of content (21 pages)

PAGE 1
Installation Manual GPS PLOTTER/SOUNDER GP-1670F GP-1870F SAFETY INSTRUCTIONS................................................................................................ i 1. MOUNTING .............................................................................................................. 1-1 1.1 Mounting of Display Unit ............................................................................................... 1-1 1.2 Replacement Kit (option) ...................................................
PAGE 2
SAFETY INSTRUCTIONS The user and installer must read the appropriate safety instructions before attempting to install or operate the equipment. The operator must read the safety instructions before attempting to operate the equipment. WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION Indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury.
PAGE 3
1. MOUNTING 1.1 Mounting of Display Unit Mounting considerations The display unit can be installed on a tabletop or flush mounted in a console. Select a suitable mounting location considering the following: • Keep the display unit out of direct sunlight. • The temperature and humidity should be moderate and stable. • Locate the unit away from exhaust pipes and vents. • The mounting location should be well ventilated. • Mount the unit where shock and vibration are minimal.
PAGE 4
1. MOUNTING 1.2 Replacement Kit (option) For replace from the flush mounted former type display unit (GP-1650 ser.) to GP1670F/1870F, the replacement kit (option) is available. Follow the procedure below to replace a display unit. 1. Remove the former display unit from panel. 2. Fix the display unit GP-1670F/1870F onto the repracement kit by four lods, washer and nuts. 3. Set the display unit to the cutout and fasten it with four tapping screws φ5×20.
PAGE 5
2. INSTALLATION OF TRANSDUCERS 2.1 How to Mount a Transducer through the Unit Transducer mounting location The thru-hull mount transducer provides the best performance of all, since the transducer protrudes from the hull and the effect of air bubbles and turbulence near the hull skin is reduced. When the boat has a keel, the transducer should be at least 30 cm away from it.
PAGE 6
2. INSTALLATION OF TRANSDUCERS Transducer mounting locations DEEP V HULL Position 1/2 to 1/3 of the hull from stern. 15 to 30 cm off center line (inside first lifting strakes.) HIGH SPEED V HULL Within the wetted bottom area Deadrise angle within 15° Installation procedure 1. With the boat hauled out of the water, mark the location chosen for mounting the transducer on the bottom of the hull. 2.
PAGE 7
2. INSTALLATION OF TRANSDUCERS 5. Mount the transducer and fairing blocks and tighten the locknut. Be sure that the transducer is properly oriented and its working face is parallel to the waterline. Flat Washer Rubber Washer Fairing Block Hull Deep-V Hull Flat Washer Hull Cork Washer Rubber Washer Flat Hull Note: Do not over-stress the stuffing tube and locknut through excessive tightening, since the wood block will swell when the boat is placed in the water.
PAGE 8
2. INSTALLATION OF TRANSDUCERS Installation procedure A suitable mounting location is at least 50 cm away from the engine and where the water flow is smooth. 1. Drill four pilot holes for self-tapping screw (5x20) in the mounting location. 2. Coat the threads of the self-tapping screws (5x14) for the transducer with silicone sealant for waterproofing. Attach the transducer to the mounting location with the self-tapping screws. 3. Adjust the transducer position so the transducer faces right to the bottom.
PAGE 9
2. INSTALLATION OF TRANSDUCERS Remarks on installation • Do the installation with the ship moored at a dock, etc. The water depth should be 6.532 feet (2-10 meters). • Turn off the engine. • Install the transducer with the engine room. • Do not power the unit with the transducer in the air, to prevent damage to the transducer. • Do not use this method on a double layer hull. • Before attaching the transducer to the hull, check that the site is suitable. Put the transducer in a water-filled plastic bag.
PAGE 10
2. INSTALLATION OF TRANSDUCERS 5. Attach the transducer to the hull. Press the transducer firmly down on the hull and gently twist it back and forth to remove any air which may be trapped in the silicone sealant. 6. Support the transducer with a piece of wood to keep it in place while the sealant is drying. It takes 24-72 hours to harden completely.
PAGE 11
3. WIRING 3.1 Display Unit All wiring are terminated at the rear of the display unit. Refer to the interconnection diagram on page S-1. Display unit (back) WARNING ELECTRICAL SHOCK CAN bus equipment Black DO NOT touch the pins inside connector. Put the cap (supplied) on the connector when power is off or the transducer is disconnected. White Shield Transducer GPS antenna unit GPA-017/017S (option) Power cable Connect the power cable to the power connector.
PAGE 12
3. WIRING 3.2 Transducer Connect the transducer cable to the XDR port. Transducer and sensor Use the optional conversion cable (02S4147) to connect the optional speed/temperature sensor and the transducer to the XDR port. Refer to Operator’s Manual in detail. Matching box (option, required for 1 kW transducer) The optional matching box (Type: MB-1100, Code No.: 000-041-353) is required to connect the optional transducers 50B-6, 50B-6B, 200B-5S, 50/200-1T and 50/20012M. Part Type Code no.
PAGE 13
NAME UNIT GP-1670F-E 999-999-181-00 HGB10AX 999-999-180-00 K10LC3005A 999-999-183-00 MINU CLOTH FRN 999-999-184-00 HBS47A 999-999-197-00 VTSPKNOB-M6 FRN 999-999-186-00 0312 003.MXP 999-999-194-00 GP-1670F DESCRIPTION/CODE № ＬＩＳＴ（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）（*）は、ﾀﾞﾐｰｺｰﾄﾞに付き、注文できません。（*） THIS CODE CANNOT BE ORDERED.
PAGE 14
NAME UNIT GP-1870F-E 999-999-182-00 HGB11AX 999-999-180-00 K10LC3005A 999-999-183-00 MINU CLOTH FRN 999-999-185-00 HBS48AX 999-999-197-00 VTSPKNOB-M6 FRN 999-999-186-00 0312 003.MXP 999-999-196-00 GP-1870F DESCRIPTION/CODE № ＬＩＳＴ（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）（*）は、ﾀﾞﾐｰｺｰﾄﾞに付き、注文できません。（*） THIS CODE CANNOT BE ORDERED.
PAGE 15
NAME UNIT ACCESSORIES SPARE PARTS OUTLINE INSTALLATION MATERIALS GP-1670F-J 999-999-180-00 K10LC3005A 999-999-183-00 MINU CLOTH FRN 999-999-184-00 HBS47A 999-999-197-00 VTSPKNOB-M6 FRN 999-999-198-00 NEWPEC AND9**.** 999-999-186-00 0312 003.MXP 999-999-194-00 GP-1670F DESCRIPTION/CODE № ＬＩＳＴ（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）（*）は、ﾀﾞﾐｰｺｰﾄﾞに付き、注文できません。（*） THIS CODE CANNOT BE ORDERED.
PAGE 16
NAME UNIT ACCESSORIES SPARE PARTS OUTLINE INSTALLATION MATERIALS GP-1870F-J 999-999-180-00 K10LC3005A 999-999-183-00 MINU CLOTH FRN 999-999-185-00 HBS48AX 999-999-197-00 VTSPKNOB-M6 FRN 999-999-198-00 NEWPEC AND9**.** 999-999-186-00 0312 003.MXP 999-999-196-00 GP-1870F DESCRIPTION/CODE № ＬＩＳＴ（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）（*）は、ﾀﾞﾐｰｺｰﾄﾞに付き、注文できません。（*） THIS CODE CANNOT BE ORDERED.
PAGE 17
6/Apr/2012 H.
PAGE 18
6/Apr/2012 H.
PAGE 19
6/Apr/2012 H.
PAGE 20
6/Apr/2012 H.
PAGE 21
C B A TNC-J-3 0.2m ジャンクションボックス JUNCTION BOX FI-5002 *2 または OR データ変換器 DATA CONVERTER IF-NMEA2K2 *2 NJTP-3DXV 1m N-P-8DFB NOTE *1: SHIPYARD SUPPLY. *2: OPTION. 注記＊１）造船所手配。＊２）オプション。 N-J-3 10m *1 IV-2sq. 整流器 (+) 1 RECTIFIER(-) 2 PR-62 *2 *2 *2 DWG.No. SCALE C4477-C01- A kg Y.NISHIYAMA H.MAKI REF.No. ST-02MSB *2 ST-02PSB 水温・船速センサー TEMP/SPEED SENSOR または OR T-02MSB *2 T-02MTB T-03MSB 水温センサー TEMP SENSOR T.