Manual

FUTABA CORPORATION

oak kandakajicho 8F 3-4 Kandakajicho, Chiyoda-ku, Tokyo 101-0045, Japan
TEL: [phone], FAX: [phone]
©FUTABA CORPORATION 2015, 10 (1)
What is S.BUS?
Different from conventional radio control systems the
S.BUS
system
uses data communication to transmit control signals from a receiver to
a servo, gyro, or other
S.BUS
compatible device.
This data includes commands such as “move the channel 3 servo to 15
degrees, move the channel 5 servo to 30 degrees” to multiple devices.
The
S.BUS
devices execute only those commands for their own set
channel. For this reason, it can be used by connecting multiple servos
to the same signal line.
Many
S.BUS
servos is in the connected state, one servo of them can be
set it up.
S.BUS2
Using the S.BUS2 port an impressive array of telemetry sensors may
be utilized. This servo is connectable with the both sides of S.BUS and
S.BUS2 port.
About the S.BUS/S.BUS2 system
S.BUS2 servo
→
it can be used in S.BUS2 and S.BUS
port.
S.BUS servo
→
it cannot be used in S.BUS2 port.
Hub
S.BUSor
S.BUS2port
S.BUSor
S.BUS2port
Conventional
CHPort
Conventional
CHPort
Transmitter
withS.BUS
setting
S.BUS/S.BUS2servoCHsettingdevice
●Canalsobeusedtogetherwithconventionalservos.
●AnS.BUS2servoconnectedtoaconventional
receiveroperatesasaconventionalservo.The
channelbecomesthereceiverconnectionpoint.The
contentssetbyprogrammablefunctionareeffective.
●TheSBD-2/SBD-1isaconverterforusing
conventionalservoswiththeS.BUS/S.BUS2system.
◆SBD-2
Eightservosareconnectable.
◆SBD-1
Threeservosareconnectable.
*BeforeinstallingtheSBD-1tothefuselage,seteachchannelateach
servoconnector(SX1~3).UsetheSBC-1S.BUSchannelchangeror
CIU-2USBadapter(S-Linksoftwareforsetting)tosetthechannel.
*SBD-1can'tbeusedatS.BUS2port.
SBD-1isusedatS.BUSport.
*Refertotheinstructionmanualofeachitemforthe
settingmethod.
SBC-1
CIU-2
S.BUS2
Servo
S.BUS2
Servo
S.BUS2
Servo
Conve-
ntional
Servo
Conve-
ntional
Servo
Conve-
ntional
Servo
Conve-
ntional
Servo
Conve-
ntional
Servo
Conve-
ntional
Servo
SBD-2
S.BUS/S.BUS2
Receiver
S.BUS/S.BUS2
Receiver
Conventional
Receiver
ŦƒƑƑƈƆƗƌƒƑŃƅƜŃŶőťŸŶŒŶőťŸŶŕŃƖƜƖƗƈƐ
●
S.BUS2
Servo
S.BUS2
Servo
S.BUS2
Servo
●
S.BUS/S.BUS2servoprogrammingdevice
or
or or
CIU-2
ŦƒƑƑƈƆƗƌƒƑŃƗƒŃƆƒƑƙƈƑƗƌƒƑƄƏŃƕƈƆƈƌƙƈƕ
ŦƒƑƑƈƆƗƌƑƊŃƆƒƑƙƈƑƗƌƒƑƄƏŃƖƈƕƙƒŃƗƒŃŶőťŸŶ
Transmitter
withS.BUS
setting
DriversandLinkprograms
＂S-Link＂mustbeinstalled.
The
ID code
of each servo is used for it.
ID code
is indicated on the
seal of the case. After carrying in a model, it is convenient, if you use
attached ID seal and CH seal when ID cannot be seen.
● S3270SV/S3270SViRatings
◆ Speed 0.12sec/60°（6.6V) 0.11sec/60°（7.4V)
◆ Torque 2.6Kgf・cm （6.6V) 3.0Kgf・cm （7.4V)
◆ Size 23.0 × 11.8 × 28.6mm
◆ Weight 16.2g
◆ RatedVoltage DC6.0V 〜 7.4V
◆ OperatingVoltage DC4.0V 〜 8.4V
*Nodrybatteryuse