Operating Instructions
Table Of Contents
- Dishwasher
- DF 280 / 281
- Table of contents
- en-us Operating instructions
- (IMPORTANT SAFETY INSTRUCTIONS 7
- ƒ Causes of Damage 10
- * Getting Started 11
- + Water softening system / special salt* 15
- , Rinse Aid 16
- - Loading the Dishwasher 18
- . Detergent 26
- / Dishwasher Cycles 28
- 0 Dishwasher Cycle Options 29
- 1 Operating the Dishwasher 31
- 2 Care and Maintenance 35
- 3 Troubleshooting 38
- 4 Customer Service 45
- ‡ Statement of Limited Product Warranty 45
- 5 Installation and connection 47
- ( Safety Definitions
- ( IMPORTANT SAFETY INSTRUCTIONS
- en-us Operating instructions
- Table des matières
- fr-ca Notice d'utilisation
- (CONSIGNES DE SÉCURITÉ IMPORTANTES 55
- ƒ Causes de pannes 58
- * Mise en marche 59
- + Système d'adoucissement de l'eau / sels* 63
- , Produit de rinçage 64
- - Chargement du lave-vaisselle 66
- . Détergent 76
- / Cycles du lave-vaisselle 78
- 0 Options de cycles du lave-vaisselle 79
- 1 Mise en marche du lave-vaisselle 81
- 2 Entretien et maintenance 85
- 3 Dépannage 89
- 4 Service à la clientèle 98
- ‡ Déclaration de la garantie limitée du produit 98
- 5 Installation et raccordement 101
- ( Indications de sécurité
- ( CONSIGNES DE SÉCURITÉ IMPORTANTES
- fr-ca Notice d'utilisation
48
en-us Installation and connection
Technical specifications
▯ Weight:
up to 132 lbs (60 kg)
▯ Voltage:
120 V, 60 Hz
▯ Connected load:
1,300 W.
▯ Circuit breaker:
12 A
▯ Power input:
off mode (Po)* 0.50 W.
left on mode (Pl)* 50 W.
*according to regulations (EU) nos. 1016/2010 and
1059/2010.
Additional functions and settings may increase the
power input.
▯ Water pressure:
at least 0.05 MPa (0.5 bar), maximum 1 MPa (10 bar).
At a higher water pressure:
connect pressure-reducing valve ahead.
▯ Inlet rate:
minimum 10 litres/minute
▯ Water temperature:
Cold water.
Hot water:
Maximum temperature 140° F (60 °C).
▯ Capacity:
12–15 place settings (depending on the features of
your dishwasher).
Installation
The required installation dimensions can be
found in the installation instructions. Level
the appliance with the aid of the height-adjustable feet.
Ensure that the appliance is situated
securely on the floor.
▯ A built-under or integrated appliance which is
installed subsequently as a free-standing appliance
must be secured to prevent it from overturning, e.g.
by screwing it to the wall or by installing it under a
continuous worktop which is screwed to adjacent
cupboards.
▯ The appliance can easily be installed in a fitted
kitchen between wooden and plastic walls.
Drain connection
1. The required work sequence can be
found in the installation instructions. If required, fit
a siphon with a drain connection.
2. Connect the drain hose to the drain
connection of the siphon with the enclosed parts.
Ensure that the drain hose is not kinked, crushed
or twisted and that there is no cover
plate in the drainage to prevent the drain water from
flowing out!
Water supply connection
1. Fasten the water supply connection to the tap
according to the installation instructions using
the enclosed parts.
Ensure that the water supply connection is not
kinked, crushed or twisted.
2. When replacing the appliance, always use a new
water supply hose.
Water pressure:
At least 7.25 PSI (0.5 bar), maximum 145 PSI (10 bar).
At a higher water pressure:
connect pressure-reducing valve ahead.
Inlet rate:
Minimum 2.65 gallons/minute (10 liters/minute)
Water temperature:
Cold water.
Hot water:
Maximum temperature 140° F (60 °C).