User guide

ManualsBrandsGamber-Johnson ManualsComputer Accessories7160-0202

CRADLE - DELL E6500-E6530

INSTALLATION INSTRUCTIONS

Product Revision Form

If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868

7160-0202

Rev. E

INST-439

Page

Figure 1

Position replicator

using locating tabs.

Right Lower

Bracket &

Mounting Screw

Vinyl Cap

#8 Nylon Lock Nut

#8 Flat Washer

Left Rear

Support Bracket

Right Rear

Support Bracket

1 / 5

Dell E-Port

Replicator

Left Lower Bracket

& Mounting Screw

7160-0202 Cradle is designed to be used with a Dell E-Port or E-Port Plus Port Replicator.

The cradle is assembled for used with Dell E6520 & E6530 computers.

By removing the two 1/8" Side Spacers, the Cradle can also be used with Dell E6510 &

E6520 computers.

By removing two 1/8" & two 3/8" Side Spacers, the Cradle can also be used with

Dell E6500 computer. (see page 2).

Tools Needed

• #2 Philips Screwdriver, • 11/32" Box Wrench, • 5/32" Hex-Key Wrench

Mounting the Port Replicator

1. Place the Port Replicator on the cradle with front and side against locating tabs.

2. Loosen screws securing Left & Right Lower Brackets, turn Brackets over Port Replicator

and re-tighten mounting screws.

(The angle on brackets must match angle on Port Replicator or computer will not dock).

3. Attach Left & Right Rear Support Brackets using (4) #8 Flat Washers and (4) #8 Nylok Nuts.

4. Verify Left and Right Rear Support Brackets do not block any replicator ports.

5. Twist (4) Vinyl Caps onto the unused threaded studs.

Product Mounting Disclaimer

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program. The OEM port

replicators used in docking cradles are not warrantied by Gamber-Johnson

Summary of content (5 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Product Revision Form INST-439 Rev. E 7160-0202 CRADLE - DELL E6500-E6530 7160-0202 Cradle is designed to be used with a Dell E-Port or E-Port Plus Port Replicator. The cradle is assembled for used with Dell E6520 & E6530 computers. By removing the two 1/8" Side Spacers, the Cradle can also be used with Dell E6510 & E6520 computers. By removing two 1/8" & two 3/8" Side Spacers, the Cradle can also be used with Dell E6500 computer. (see page 2).
PAGE 2
INSTALLATION INSTRUCTIONS Product Revision Rev. E 7160-0202 CRADLE - DELL E6500-E6530 Form INST-439 Adjusting the Side Brackets 1. After the port Replicator has been installed, open the cradle by pushing the latch button and pulling the sides outward. 2. Mount the computer onto the Port Replicator. A secure mount is confirmed with an audible click of the Port Replicator. 3. If a E6500 computer is being used, take off both side hooks and remove the 1/8" & one 3/8" thick spacer from each side. 4.
PAGE 3
INSTALLATION INSTRUCTIONS Product Revision Form INST-439 Rev. E 7160-0202 CRADLE - DELL E6500-E6530 Motion Attachment Secure the Motion Attachment with (4) .25-20 x .50 Socket Button Head Cap Screws supplied in Hardware Bag 7120-0468 using a 5/32" Hex-Key Wrench. .25-20 x .
PAGE 4
INSTALLATION INSTRUCTIONS Product Revision Rev. E 7160-0202 CRADLE - DELL E6500-E6530 Form INST-439 Accessories (see Figure 4) Tools Needed 9/64" Hex-Key Wrench 11/21" Box Wrench #2 Philips Screw driver Screen Support 1. Secure the Screen Support to the left side of the Cradle using (2) #8-32 x .50 Socket Head Cap Screws and (2) #8 Flat Washers with a 9/64 Hex-Key Wrench. 2.
PAGE 5
INSTALLATION INSTRUCTIONS Product Revision Rev. E 7160-0202 CRADLE - DELL E6500-E6530 Form INST-439 Screen Support #8-32 X .50 socket head cap screw #8 flat wahser #8-32 X .50 socket head cap screw Adjust width then secure #8 flat wahser #8-32 nylon lock nut #8 flat wahser #8-32 X .50 socket head cap screw Figure 4 Isolator #6-32 x .25 pan head screw #8-32 x .