Model 27881 2.
Equipment Approval Information Your telephone equipment is approved for connection to the Public Switched Telephone Network and is in compliance with parts 15 and 68, FCC Rules and Regulations and the Technical Requirements for Telephone Terminal Equipment published by ACTA. 1 Notification to the Local Telephone Company On the bottom of this equipment is a label indicating, among other information, the US number and Ringer Equivalence Number (REN) for the equipment.
Interference Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Table of Contents Equipment Approval Information..................2 Interference Information. ............................3 Hearing Aid Compatibility (HAC)..................3 Licensing......................................................3 FCC RF Radiation Exposure Statement.........3 Table of Contents........................................4 Introduction................................................6 Before You Begin.........................................6 Parts Checklist...............................
Table of Contents Corded Handset........................................ 21 Cordless Handset.....................................21 Answering System.....................................21 Speakerphone Operation............................... 21 Receiving a Call with Speakerphone. .... 22 Making a Call with Speakerphone......... 22 Switching Between Speakerphone and Handset.......................................................22 Intercom Operation........................................
Introduction CAUTION: When using telephone equipment, there are basic safety instructions that should always be followed. Refer to the IMPORTANT SAFETY INSTRUCTIONS provided with this product and save them for future reference. IMPORTANT: Because cordless phones operate on electricity, you should have at least one phone in your home that isn’t cordless, in case the power in your home goes out. Before You Begin Parts Checklist Make sure your package includes the items shown here.
Installation Digital Security System Your cordless phone uses a digital security system to protect against false ringing, unauthorized access, and charges to your phone line. INSTALLATION NOTE: Some cordless telephones operate at frequencies that may cause or receive interference with nearby TVs, microwave ovens, and VCRs. To minimize or prevent such interference, the base of the cordless telephone should not be placed near or on top of a TV, microwave ovens, or VCR.
Handset and Charge Cradle Layout Display TALK/call back (button) VOL/CID -/+ (volume/caller ID -/+ buttons) FORMAT/answerer (button) REDIAL (button) MEMORY/ conference (button) 7(review button) charge cradle with power supply 8(skip button) erase button) play/stop (button) TONE */exit (button) PAUSE# (button) FLASH/program (button) CHAN/delete (button) ringer (switch) Base Layout ANSWERER ON/OFF (button) intercom (button) PLAY/STOP (button) NEW MESSAGE display (indicator) ANNOUNCE (button) R
Installing the Phone Installing the Handset Battery NOTE: You must connect the handset battery before using the cordless handsets. CAUTION: To reduce the risk of fire or personal injury, only use the Thomson Inc. approved Nickel-Cadmium battery model 5-2459, which is compatible with this unit. 1. Locate battery and battery door which are packaged together inside a plastic bag and are separate from the handset. 2. Locate the battery compartment on the back of the handset. 3.
Installing the Phone Choose the best location to install your base and handset charge cradles. Your base and handset charge cradles should be placed on a level surface such as a desk or table top, or you may mount the base on a wall. Connecting the AC (Electrical) Power 1. On the base, plug the AC power adaptor cord into the power jack on the back of the base and the other into an electrical outlet. If desired, store the excess AC power adaptor line cord inside desktop pedestal.
Wall Mounting the Base The base is packaged with the pedestal attached in desktop mode. To mount the base on the wall: 1. Turn the base over and remove the pedestal. 2. Rotate the pedestal a half turn, and align it with the bottom of the base. 3. Attach the pedestal by first inserting the tabs on the pedestal into the slots on the bottom of the base, and then push the pedestal down until it snaps into place. 4.
Telephone Set Up There are twelve programmable menus available on the base: Language, Display Contrast, Rings to Answer, Security Code, Ringer Level, Ringer Tone, Tone/Pulse, Set Day, Set Time, Local Area Code, Link Cordless Handset, and Default Setting. There are five programmable menus available on the handset: Language, Local Area Code, Ringer Tone, Link Base, and Default Setting. NOTE: To exit the menu without making changes, press the *TONE/ EXIT button on the base or TONE*/exit on the handset.
2. Press 1, 2 or 3 on the base touch-tone pad to enter your selection, or use the REVIEW or NEXT button on the base to scroll to your selection. 3. Press FLASH/PROGRAM again to store your selection. Rings to Answer NOTE: This setting may only be made with the base. You may set the number of times you want the phone to ring before the answering system answers a call. 1. Press the FLASH/PROGRAM button until RING TO ANSWER shows in the display. 5 is the default setting. 2.
3. Press FLASH/PROGRAM again to store your selection. You will hear a confirmation tone. Ringer Level NOTE: This setting may only be made with the base. 1. Press the FLASH/PROGRAM button until SET RING LEVEL shows in the display. 1HI is the default setting. 2. Press 1, 2 or 3 on the base touch-tone pad to enter your selection, or use the REVIEW or NEXT button to scroll to your selection. 3. Press FLASH/PROGRAM again to store your selection.
2. Use the touch-tone pad to select 1TONE or 2PULSE, or press the REVIEW or NEXT button to scroll to 1TONE or 2PULSE. 3. Press FLASH/PROGRAM again to store your selection. You will hear a confirmation tone. NOTE: If you aren’t sure which dialing system you have, set the telephone to tone dialing and make a test call. If the call connects, the setting is correct. If the call does not connect, set the telephone to pulse dialing. Setting Day/Time NOTE: This setting may only be made with the base.
2. Use the cordless handset or base number pad to enter your three digit area code. NOTE: If you make a mistake, press the DELETE button to erase a wrong number. 3. Press FLASH/PROGRAM again to store your selection. Registration Registration links the base to a cordless handset. Once a handset is registered it can use the base’s phone connection. A cordless handset will not operate until it is registered to the base. During the registration process, keep the handset near the base. 1.
Basic Operation Answering a Call Check the display to see who is calling. Cordless Handset 1. Press the TALK/call back button on the handset. 2. When finished, press TALK/call back or place the handset in the charge cradle to hang up. Corded Handset 1. Lift the handset. 2. When finished, put the handset back on the cradle to hang up. Base Speakerphone 1. Press the SPEAKER/CALL BACK button. 2. When finished, press SPEAKER/CALL BACK to hang up.
Speakerphone 1. Press the SPEAKER/CALL BACK button. 2. Wait for a dial tone, then dial the desired number. Or, dial the number and then press the SPEAKER/CALL BACK button. 3. When finished, press SPEAKER/CALL BACK to hang up. Manual Channel Selection While talking, you might need to manually change the channel in order to reduce static caused by baby monitors, garage door openers, or other cordless phones.
Flash Use the FLASH/PROGRAM buttons on the base and cordless handset to activate custom calling services such as call waiting or call transfer, which are available through your local phone company. TIP: Don’t use the TALK/call back (handset) or SPEAKER/CALL BACK (base) button to activate custom calling service such as call waiting, or you’ll hang up the phone. Last Number Redial To quickly redial the last number you dialed: Base Speakerphone 1. Press the SPEAKER/CALL BACK button. 2.
Hold Press the HOLD button on the base to put a call on hold. The hold indicator light turns on. To take a call off hold, press the HOLD button again, and the hold indicator light turns off. • To switch a call on hold from the base to the cordless handset, press TALK/call back on the cordless handset. If you continue the call on a separate extension phone, your phone releases the line to the extension phone, and the hold indicator light turns off.
1. Dial the telephone number and wait for the line to connect. 2. When your call is answered, press the TONE*/exit button on your cordless handset or the *TONE/EXIT button on your base number pad to temporarily change from pulse dialing to tone dialing. 3. Follow the automated instructions to get the information you need. 4. Hang up the phone and the phone automatically returns to pulse (rotary) dialing mode. Volume Speakerphone Adjust the base unit speaker volume by pressing the SPKR VOL + and - buttons.
Note the following guidelines when using the speakerphone. • Stay reasonably close to the phone so that you can be clearly heard by the person to whom you are speaking. • The SPEAKER indicator is on when the speakerphone is in use. Receiving a Call with Speakerphone 1. When the phone rings, press and release the SPEAKER/CALL BACK button on the base, and speak normally, at a minimum distance of 8-9 inches, into the built-in microphone. 2.
In Speakerphone mode, press the HOLD button on the base unit to place the call on hold. Then press TALK/call back button on cordless handset or lift the corded handset. Speak into the handset. Corded/Cordless Handset to Speaker — Press SPEAKER/CALL BACK, then hang up the handset. Speak into the Speakerphone.
Using Intercom with a Telephone Call During a telephone call, you can use the intercom/paging function to page the base or cordless handset and set up a private (2-way) intercom conversation with another user while the telephone call is placed on hold. Or, you can create a 3-way conversation between the telephone caller, the base, and the cordless handset. Two-Way Intercom Calls 1.
Caller ID (CID) IMPORTANT: In order to use this unit’s Caller ID features, you must subscribe to either the standard Name/Number Caller ID Service or Call Waiting Caller ID Service. To know who is calling while you are on the phone, you must subscribe to Call Waiting Caller ID Service. This unit receives and displays CID information transmitted by your local telephone company. This information can include the phone number, date and time; or the name, phone number, and date and time.
Storing CID Records (In CID Memory) If you are not at home or cannot answer, your telephone’s Caller ID memory stores the data for the most recent 40 calls you received so that you can see who called while you were unavailable. When the 41st call is received, the oldest Caller ID record (1st call) is automatically deleted. You may review the stored information at any time. Calls received since your last review are marked as NEW in the display.
Dialing a Caller ID Number When reviewing any call record in the Caller ID memory, you can dial back the caller’s number. 1. Make sure the phone is OFF (not in talk mode). 2. Press REVIEW or NEXT button (base) or VOL/CID (- or +) button (cordless handset) until the desired call record is displayed.
If the number is corrupted, such as a number in a name or an alphabetical character in a number, an error tone comes from the handset and the number won’t dial. Storing CID Records in Internal Memory You may transfer a Caller ID record to your phone’s memory. NOTE: It is important that you format CID records correctly before storing in memory. It is not possible to reformat CID records stored in memory. 1.
2. Press and hold DELETE (base) or CHAN/delete (cordless handset). The display asks DELETE ALL? for several seconds. 3. Press DELETE (base) or CHAN/delete (cordless handset) again, within ten seconds, to erase all records. The display shows NO CALLS. Caller ID Errors If there is an error in the transmission of information to your Caller ID phone, ERROR shows in the display. If you have not subscribed to Caller ID service or it is not working, NO DATA shows in the display.
5. Press the MEM/CONFERENCE (base) or MEMORY/conference (cordless handset) button again to save your selection. The display shows ENTER TEL NUMBR. NOTE: If you make a mistake, press the DELETE button on the base or CHAN/delete on the handset to backspace and erase the wrong character(s) or number(s). 6.
To Change: Follow the steps under Storing a Name and Number in Memory except replace the stored name or number with the new information. To Delete: Press the MEM/CONFERENCE (base) or MEMORY/conference (cordless handset) button, then press the desired memory location button (0 through 9 number keys) or use the REVIEW or NEXT button (base) or the VOL/CID (- or +) button (cordless handset) to scroll to a desired memory. 1.
-Or1. Make sure the phone is OFF (not in talk mode). 2. Press the MEM/CONFERENCE button. 3. Press the desired memory location button (0-9), or use the REVIEW or NEXT button to scroll to the desired telephone number. 4. Press the SPEAKER/CALL BACK button. The number dials automatically. Chain Dialing from Memory Use this feature to make calls that require a sequence of numbers, such as a frequently used long distance card number.
Answering System Operation Recording the Outgoing Announcement For best results when recording, you should be about nine inches from the microphone, and eliminate as much background noise as possible. 1. Make sure the answering system is ON. 2. Press and hold the ANNOUNCE button on the base while you record the announcement. 3. Begin speaking after you hear the beep. You have up to two minutes of recording time. 4. Release the button after you finish your announcement.
Message Playback from Base Unit To play messages, press the PLAY/STOP button on the base. While a message is playing, you can do the following: • Press the PLAY/STOP button to stop the message playback. • Press and release the REVIEW button to restart the current message; continue to press and release the REVIEW button to go to previous messages. • Press and release the NEXT button to go to the next message. • Press the PLAY/STOP button to stop message playback.
3. Press erase on the handset (the 0 key) to erase the message that is playing. NOTE: Erased messages cannot be restored. Also, be careful not to press the erase button as the next unheard message is playing because that message will also be erased. Leaving a Memo Use the memo feature to leave a message. 1. Press and hold the MEMO button (base) down until you finish the message. 2. Begin speaking after you hear the beep. 3. Release the MEMO button after you are finished.
• Press the PLAY/STOP button (2 key) to stop the message playback (press PLAY/STOP again to start over at the voice menu.) • Press the 7 button (1 key) to restart the current message. • Press the 8 button (3 key) to go to the next message. • Quickly press and release the 7 button (1 key) repeatedly to scroll through previous messages. When you are finished listening to your messages, press the FORMAT/answerer button again to quit. NOTE: You may listen to the voice menu at any time by pressing 7.
Accessing the Answering System from Another Location You can access your answering system from any touch-tone phone by entering your 3-digit security code after you hear the outgoing announcement. 1. Dial the phone number the answering system is connected to. 2. After the answering system answers, enter the security code after you hear the tone. 3. Follow the voice menu to use the answering system’s remote functions.
Changing the Battery CAUTION: To reduce the risk of fire or personal injury, use only the Thomson Inc. approved Nickel-Cadmium (Ni-Cd) battery model 5-2459, which is compatible with this unit. 1. Make sure handset is OFF (not in TALK mode) before you replace battery. 2. Remove the battery compartment door. 3. Disconnect the battery plug from the jack inside the battery compartment and remove the battery pack from the handset. 4.
Display Messages The following indicators show the status of a message or of the unit. BLOCKED NUMBER The person is calling from a number that has been blocked from transmission. DELETE? Prompt asking if you want to erase one of the 10 numbers stored in the phone’s outgoing memory. DELETE ALL? Prompt asking if you want to erase all Caller ID records. DELETE CALL ID? Prompt asking if you want to erase the current Caller ID record that is shown on the display.
Handset Sound Signals Signal Meaning A long warbling tone (with ringer on) Three short beeps One short beep (every 7 seconds) Signals an incoming call Page signal Low battery warning Troubleshooting Guide Telephone Solutions No dial tone • Check and repeat installation steps: Ensure the base power cord is connected to a working outlet . Ensure the telephone line cord is connected to the base and the wall jack.
You experience static, noise, or fading in and out • Change channels. • The cordless handset may be out of range of the base. Move closer to the base. • Make sure base is not plugged into an outlet with another household appliance. • Charge the battery. Unit beeps • Place the handset in the cradle for 20 seconds. If it still beeps, charge battery for 16 hours. • Clean charging contacts on cordless handset and charge cradle with a soft cloth or an eraser. • See solutions for “No dial tone” on previous page.
No Caller ID • In order to receive Caller ID information, you must subscribe to the standard name/number Caller ID service from your local telephone company. Battery Solutions If you experience any of the following problems, even after fully recharging the battery, you may need to replace the battery pack: • Short talk time • Poor sound quality • Limited range Causes of Poor Reception • Aluminum siding. • Foil backing on insulation.
General Product Care To keep your unit working and looking good, follow these guidelines: • Avoid putting the phone near heating appliances and devices that generate electrical noise (for example, motors or fluorescent lamps). • DO NOT expose to direct sunlight or moisture. • Avoid dropping the handset, as well as other rough treatment to the phone. • Clean the phone with a soft cloth. • Never use a strong cleaning agent or abrasive powder because this will damage the finish.
Index A Accessing the Answering System from Another Location 37 Accessory Information 47 Answering an Intercom Call 23 Answering a Call 17 Answering System Indicator 36 Answering System Operation 33 Answering System Set Up 11 Auto Standby 18 B Base Layout 8 Basic Operation 17 Battery Safety Precautions 38 Before You Begin 6 C Caller ID (CID) 25 Caller ID Errors 29 Call Timer 18 Call Waiting Caller ID 25 Causes of Poor Reception 42 Chain Dialing from Memory 32 Changing the Battery 38 Changing the Security
Index Local Area Code 15 S M Screening Calls from the Base 33 Screening Calls from the Handset 36 Security Code 13 Service 43 Setting Day/Time 15 Speakerphone Operation 21 Storing a Name and Number in Memory 29 Storing a Redial Number 30 Storing CID Records (In CID Memory) 26 Storing CID Records in Internal Memory 28 Switching Between Speakerphone and Handset 22 Making an Intercom Call 23 Making a Call 17 Making a Call with Speakerphone 22 Manual Channel Selection 18 Memory 29 Memory Full 34,36 Message
Limited Warranty What your warranty covers: • Defects in materials or workmanship. For how long after your purchase: • One year, from date of purchase. (The warranty period for rental units begins with the first rental or 45 days from date of shipment to the rental firm, whichever comes first.) What we will do: • Provide you with a new or, at our option, a refurbished unit. The exchange unit is under warranty for the remainder of the original product’s warranty period.
Limitation of Warranty: • The warranty stated above is the only warranty applicable to this product. All other warranties, express or implied (including all implied warranties of merchantability or fitness for a particular purpose) are hereby disclaimed. No verbal or written information given by Thomson Inc., its agents, or employees shall create a guaranty or in any way increase the scope of this warranty. • Repair or replacement as provided under this warranty is the exclusive remedy of the consumer.
Model 27881 00009246 (Rev. 1 Dom E/S) 07-22 Printed in China Thomson Inc. 101 Weest 103rd St. Indianapolis, IN 46290-1102 © 2007 Thomson Inc.
2.
Información Sobre la Aprobación de Equipo El equipo de su teléfono esta aprobado para la conexión con la red Telefónica Pública (Public Switched Telephone Network) y cumple con los requisitos establecidos en las secciones 15 y 68 de las Reglas y Regulaciones de la FCC y con los Requerimientos Técnicos para Equipos de Terminales Telefónicas (Technical Requirements for Telephone Terminal Equipment), publicado por ACTA.
Información de Interferencias Este artefacto cumple con la Parte 15 de las Reglas de la FCC. Su funcionamiento es sujeto a las dos condiciones siguientes: (l) Este artefacto no puede causar interferencia dañosa, y (2) Este artefacto debe aceptar cualquier interferencia recibida, incluyendo interferencia que puede causar un funcionamiento no deseado. Este equipo ha sido probado y cumple con los límites para un artefacto digital de la Clase B, de conformidad con la Parte 15 de las Reglas de la FCC.
Tabla de Contenido Información Sobre la Aprobación de Equipo 2 Información de Interferencias......................3 Compatibilidad con Audífonos (CCA)............3 Licensing......................................................3 Estatuto sobre la Exposición a la Radiación de la FCC RF............................................3 Tabla de Contenido......................................4 Tabla de Contenido......................................5 Introducción................................................
Tabla de Contenido Sistema Contestador. ............................... 21 Operación del Altavoz................................... 21 Para Recibir una Llamada con el Altavoz. ....................................................... 22 Para Hacer una Llamada con el Altavoz. ....................................................... 22 Para Alternar entre el Altavoz y el Auricular.................................................... 22 Operación del Interfono...............................
Introducción CUIDADO: Cuando utilice equipo telefónico, hay instrucciones básicas de seguridad que siempre deben seguirse. Refiérase a la guía de INSTRUCCIONES DE SEGURIDAD IMPORTANTES provista con este producto y guárdela para referencia futura. IMPORTANT: Como los teléfonos inalámbricos operan con electricidad, usted debe tener por lo menos un teléfono en su casa que no sea inalámbrico, en caso de una interrupción de corriente.
Instalación Sistema Digital de Seguridad Su teléfono inalámbrico usa un sistema de seguridad digital para evitar el timbrado falso, el uso no autorizado y cargos a su línea telefónica. NOTA SOBRE LA INSTALACIÓN: Algunos teléfonos inalámbricos operan a frecuencias que pueden causar o recibir interferencia con aparatos de televisión, hornos de microondas, hornos, o videocaseteras que se encuentren cerca de este aparato.
Formato del Auricular y del Cargador Pantalla TALK/call back (botón para hablar/devolver el llamado) FORMAT/answerer (botón para formato/ contestadora) VOL/CID -/+ (botones del identificador/volumen) MEMORY/ conference (botón para memoria/conferencia) 8 (botón para saltar mensajes) REDIAL (botón para volver a marcar) 7 (botón para revisar) erase (botón para borrar) TONE */exit (botón para tono/salir ) CHAN/delete (botón para canal/ borrar) Formato del Auricular y del Cargador ringer (selector del tim
Para Instalar el Teléfono Para Instalar la Batería del Auricular NOTA: Usted debe conectar la batería del auricular antes de utilizar el aparato. PRECAUCION: Para reducir el riesgo de fuego o lastimaduras personales, use solamente la batería de Ni’quel-Cadmio (Ni-Cd) modelo 5-2459 aprobado por Thomson Inc. eso es compatible con esta unidad. 1. Localice la puerta de la batería y la batería que vienen empacadas juntos dentro de una bolsa de plástico y están separados del auricular. 2.
Para Instalar el Teléfono Escoja la mejor localización para instalar la base y el cargador del auricular. La base y el cargador deben ser chocados sobre una superficie plana como un escritorio o una mesa, o usted puede montar la base sobre la pared. Para Conectar la Corriente AC (Eléctrica) 1. En la base, conecte el cable de corriente dentro del enchufe en la parte posterior de la base y conecte el otro extremo en un enchufe de corriente eléctrica.
Montaje de la Base sobre Pared La base está empacada con el pedestal instalado en modalidad para superficie plana. Para montar la base sobre la pared: 1. Volteé la base de cabeza y quite el pedestal. 2. Gire el pedestal una media vuelta, para poder alinearlo con la parte de abajo de la base. 3. Sujete el pedestal introduciendo primero las lengüetas del pedestal dentro de las ranuras en la parte de abajo de la base, y después empujando el pedestal hacia abajo hasta que quede sujeto en su sito. 4.
Programación del Teléfono Hay doce menús programables disponibles en la base: Idioma, Contraste de la Pantalla, Timbres para Contestar, Código de Seguridad, Nivel del Timbre, Tono del Timbre, Tono/Pulso, Programación de Fecha, Programación de Hora, Clave de Área Local, Auricular de Enlace Inalámbrico, y Programaciones de Fábrica. Hay cinco menús programables disponibles en el auricular: Idioma, Clave de Área Local, Tono del Timbre, Enlace Base, y Programaciones de Fábrica.
Timbres para Contestar NOTA: Esta programación puede hacerse únicamente con la base. Usted puede programar el número de veces que usted quiere que su teléfono suene antes de que el sistema contestador conteste la llamada. 1. Oprima el botón FLASH/PROGRAM hasta que la indicación TIMBR CONTESTAR aparezca en la pantalla. 2. Oprima el 3 o el 5 o utilice el botón REVIEW o NEXT para seleccionar 3, 5 o TOLL.
Nivel del Timbre NOTA: Esta programación puede hacerse únicamente desde la base. 1. Oprima el botón FLASH/PROGRAM hasta que la indicación PROG NIVEL TIMB. La programación de fábrica es 1ALT. 2. Oprima 1, 2, o 3 en el teclado numérico de la base para inscribir su selección, u oprima el botón REVIEW o NEXT para llegar a su selección. 3. Oprima nuevamente el botón FLASH/PROGRAM para almacenar su selección. NOTA: Si usted apaga el timbre (OFF), la indicación TIMBRE DESACTIV aparece en la pantalla de la base.
NOTA: Si usted no está seguro qué servicio de marcado tiene, programe el teléfono en marcado por tono y haga una llamada de prueba. Si la llamada hace conexión, la programación está correcta. Si no hace conexión, entonces programe el teléfono para modalidad de pulso. Para Programar la Fecha/Hora NOTA: Esta programación puede hacerse únicamente desde la base. La hora es transmitida automáticamente por su compañía telefónica local como parte del servicio de Identificador de Llamadas.
Registro El registro enlaza la base a un auricular inalámbrico. Una vez que el auricular está registrado, puede utilizar la conexión telefónica de la base. Un auricular inalámbrico no operará hasta que esté registrado con la base. Durante el proceso de registro, mantenga el auricular cerca de la base. 1. Oprima el botón FLASH/PROGRAM en la base hasta que la indicación ENLAZAR AURIC? aparezca en la pantalla. La programación de fábrica es 2NO. 2.
Operación Básica Para Contestar una Llamada Verifique la pantalla para saber quién llama. Auricular Inalámbrico 1. Oprima el botón TALK/call back en el auricular. 2. Al terminar, presione TALK/call back o coloque el auricular en la base de carga para colgar. Auricular Alámbrico 1. Levante el auricular. 2. Cuando haya terminado, ponga nuevamente el auricular en su sitio para colgar. Altavoz en la Base 1. Oprima el botón SPEAKER/CALL BACK. 2.
Altavoz 1. Oprima el botón SPEAKER/CALL BACK. Espere al tono de marcar, y después marque el número deseado. -O2. Marque el número primero y después oprima el botón SPEAKER/CALL BACK. 3. Cuando usted haya terminado, oprima el botón SPEAKER/CALL BACK para colgar. Selección Manual de Canales Mientras usted está hablando, usted puede necesitar cambiar manualmente el canal para reducir estática causada por monitores de bebé, aparatos para abrir la cochera, u otros teléfonos celulares.
Flash Utilice los botones FLASH/PROGRAM en la base o en el auricular inalámbrico o en la base para activar los servicios especiales, como llamada en espera, que le son disponibles a través de su compañía telefónica local. SUGERENCIA: No oprima el botón TALK/call back (auricular) o el botón SPEAKER/CALL BACK (base) para activar un servicio de llamadas, como llamada en espera, porque de ser así, usted colgará el teléfono.
En Espera Oprima el botón HOLD en la base para poner una llamada en espera. El indicador de espera se ilumina. Para tomar una llamada que está en espera, oprima y sostenga el botón HOLD nuevamente, y el indicador de espera se apaga. • Para pasar una llamada en espera de la base al auricular inalámbrico, oprima el botón TALK/call back en el auricular inalámbrico.
1. Marque el número telefónico o espere a que su llamada se conecte. 2. Cuando su llamada es contestada, oprima el botón TONE*/EXIT en su auricular inalámbrico o el botón *TONE/EXIT en el teclado numérico de la base para cambiar temporalmente de modalidad por pulso a modalidad de marcado por tono. 3. Siga las instrucciones orales para obtener la información que necesita. 4. Cuelgue el teléfono y éste automáticamente vuelve a la modalidad de marcado por pulso (rotatorio).
Para Recibir una Llamada con el Altavoz 1. Cuando el teléfono timbra, oprima y suelte el botón SPEAKER/CALL BACK en la base, y hable normalmente, a una distancia mínima de 8-9 pulgadas, en el micrófono integrado. 2. Ajuste el volumen del altavoz oprimiendo el botón SPKR VOL + o – en la base. 3. Para terminar una llamada, oprima nuevamente el botón SPEAKER/CALL BACK. Para Hacer una Llamada con el Altavoz 1. Oprima y suelte el botón SPEAKER/CALL BACK en la base, y espere al tono de marcar. 2.
Operación del Interfono Una llamada bi-direccional es posible entre la base y el auricular inalámbrico sin ocupar la línea telefónica y como el teléfono no está en uso, usted puede todavía recibir llamadas entrantes. Para Hacer una Llamada de Interfono 1. Asegúrese que su teléfono esté en modalidad de apagado (OFF) (no en modalidad de marcar). 2. Oprima el botón PAGE/INTERCOM (en la base) o el botón intercom (en el auricular). Un tono localizador suena en la base y en al auricular inalámbrico. 3.
Llamadas de Interfono de Dos Personas 1. Para hacer una llamada con interfono, oprima el botón PAGE/INTERCOM (en la base) o el botón intercom (en el auricular inalámbrico), dependiendo de dónde se originó la llamada externa. La persona en la llamada externa se pone en espera y ambos usuarios del interfono pueden hablar en privado. 2. Para contestar la llamada del interfono, oprima el botón PAGE/INTERCOM (en la base) o el botón intercom (en el auricular inalámbrico).
Funciones del Identificador de Llamadas (Caller ID) IMPORTANTE: Para utilizar las características de la identificación de llamador de esta unidad, usted debe suscribirse a cualquiera de los servicios de Identificador de Llamadas, ya sea el servicio estándar de Identificador de Nombre/Número o el servicio de Identificador de Llamada en Espera. Para saber quién llama miestras usted está en el teléfono, usted necesita suscribirse al servicio de Identificador de Llamada en Espera.
Almacenar Archivos del Identificador de Llamadas (en la Memoria de CID) Si usted no está en casa o no puede contestar, la memoria del Identificador de Llamadas de su teléfono automáticamente almacena la información de las 40 últimas llamadas para que sepa quién llamó mientras usted no estuvo disponible. Cuando la llamada número 41 es recibida, el último archivo del Identificador de Llamadas (la primera llamada) se borra automáticamente. Usted puede revisar la información almacenada en cualquier momento.
Para Marcar un Número del Identificador de Llamadas Mientras usted revisa los archivos del Identificador de Llamadas, usted puede llamar al número telefónico que se muestra en la pantalla. 1. Asegúrese que el teléfono esté desactivado (OFF) (no en modalidad para hablar). 2. Utilice el botón REVIEW o NEXT (base) o el botón VOL/CID (- o +) (auricular inalámbrico) hasta que el archivo deseado aparezca en la pantalla.
Almacenar Archivos del Identificador de Llamadas en la Memoria Interna Usted puede transferir archivos del Identificador de Llamadas a la memoria de su teléfono. NOTA: Es importante que usted formatee los archivos del Identificador de Llamadas (CID) correctamente antes de almacenarlos en la memoria. No es posible volver a formatear los archivos del Identificador (CID) almacenados en la memoria. 1.
3. Oprima nuevamente el botón DELETE (base) o CHAN/delete (auricular inalámbrico), dentro de los siguientes diez segundos, para borrar todos los archivos. La pantalla muestra la indicación NO LLAMADA. Errores del Identificador de Llamadas Si hay un error en la transmisión de información de su teléfono con Identificador de Llamadas, la indicación ERROR aparece en la pantalla.
5. Oprima el botón MEM/CONFERENCE (en la base) o MEMORY/conference (en el auricular inalámbrico) nuevamente para salvar su selección. La pantalla muestra INSCR NUMERO. NOTA: Si Ud. comete un error, presione el botón DELETE en la base o CHAN/delete en el auricular para retroceder y borrar el carácter o número (o caracteres) o (números) erróneos. 6.
Para Cambiar: Siga los pasos bajo “Para Almacenar un Nombre y un Número en la Memoria” excepto reemplace el nombre o número almacenado con la información nueva. Para Borrar: Presione el botón MEM/CONFERENCE (base) o MEMORY/conference (auricular inalámbrico), luego presione el botón de ubicación de memoria deseado (teclas numéricas 0 a 9) o use el botón REVIEW o NEXT (base) o el botón VOL/CID (- o +) (en el auricular inalámbrico) para desplazarse a una ubicación de memoria deseada. 1.
-O1. Asegúrese que el teléfono esté desactivado (OFF) (no en modalidad para hablar –TALK). 2. Oprima el botón MEM/CONFERENCE. 3. Oprima el botón de la localización de memoria deseada (0-9), u oprima el botón REVIEW o NEXT para recorrer los números hasta llegar al número deseado. 4. Oprima el botón SPEAKER/CALL BACK. El número almacenado se marca automáticamente.
Operación del Sistema Contestador Para Grabar el Anuncio Saliente Para mejores resultados, usted debe estar aproximadamente a nueve pulgadas del micrófono, y eliminar tanto ruido de fondo como le sea posible. 1. Asegúrese que el sistema contestador esté activado (ON). 2. Oprima y sostenga el botón ANNOUNCE en la base mientras usted graba el anuncio. 3. Comience a hablar después de que usted escuche el tono. Ud. tiene hasta dos minutos de tiempo de grabación. 4.
Reproducción de Mensajes desde la Base del Aparato Para reproducir los mensajes, oprima el botón PLAY/STOP en la base. Mientras un mensaje se reproduce, usted puede hacer lo siguiente: • Oprimir el botón PLAY/ STOP para detener la reproducción de los mensajes. • Oprima el botón REVIEW una vez para volver a escuchar el mensaje actual; continúe oprimiendo y soltando el botón REVIEW para ir a los mensajes previos. • Oprima y suelte el botón NEXT para ir al siguiente mensaje.
NOTA: Los mensajes borrados no pueden ser recuperados. También, tenga cuidado de no oprimir el botón para borrar cuando el siguiente mensaje que usted no ha escuchado se está reproduciendo porque ese mensaje será borrado también. Para Dejar un Recado (MEMO) Utilice la función de recado para dejar un mensaje para usted. 1. Oprima y sostenga el botón MEMO (en la base) hasta que usted termine el recado. 2. Empiece a hablar después de que usted escuche el tono. 3.
• Presionar y soltar el botón 8 (tecla 3) para ir al siguiente mensaje. • Presionar rápidamente y soltar el botón 7 (tecla 1) repetidamente para desplazarse a través de los mensajes previos. Cuando Ud. haya terminado de escuchar sus mensajes, presione el botón FORMAT/answerer otra vez para salir. NOTA: Usted puede escuchar el menú de voz en cualquier momento presionando 7. Indicador del Sistema Contestador El sistema contestador viene programado como activo.
Para Tener Acceso al Sistema Contestador desde Otra Localización Usted puede tener acceso a su sistema contestador desde cualquier teléfono de tono inscribiendo su código de 3 dígitos después de que usted escuche el anuncio saliente. 1. Marque el número telefónico al que el sistema contestador esté conectado. 2. Cuando el contestador conteste, inscriba el código de seguridad después de que usted escuche el tono. 3.
Cómo Cambiar la Batería PRECAUCION: Para reducir el riesgo de fuego o lastimaduras personales, use solamente la batería de Ni’quel-Cadmio (Ni-Cd) modelo 5-2459 aprobado por Thomson Inc. eso es compatible con esta unidad. 1. Asegúrese que el teléfono esté desactivado (no en modalidad para hablar) antes de cambiar la batería. 2. Quite la tapa del compartimiento de la batería. 3. Desconecte el enchufe de la batería en la conexión dentro del compartimiento y saque la batería del auricular. 4.
Mensajes en la Pantalla Los siguientes mensajes especiales indican el estado actual de un mensaje o del aparato: BORRAR? Indicación preguntándole si quiere borrar uno de los 10 números almacenados en la memoria saliente del teléfono. BORRAR ARCHIVO? Indicación preguntándole si quiere borrar el archivo actual del Caller ID que se muestra en la pantalla. BORRAR TODO? Indicación preguntándole si quiere borrar todos los archivos del Caller ID.
Señales Sonoras del Auricular Señal Un tono de gorgeo largo (con timbre encendido) Tres tonos cortos Un “bip” corto (cada 7 segundos) Significado Señala que una llamada está entrando Señal del localizador Advertencia de baja batería Solución de Problemas Soluciones para el Teléfono No hay tono de marcar • Verifique y repita los pasos de la instalación: Asegúrese que el cable de corriente de la base esté conectado a un enchufe que sirva.
Usted experimenta estática, ruido, o debilitamiento del sonido entrante o saliente • Cambie canales. • El auricular inalámbrico puede estar fuera de rango con la base. Acérquelo a la base. • Asegúrese de que la base no esté conectada en un enchufe con otro aparato eléctrico. • Cargue la batería. El aparato emite “bips” • Coloque el auricular sobre la base durante 20 segundos. Si sigue emitiendo “bips”, cargue la batería durante 16 horas.
No sirve el Caller ID • Para pode recibir la información del Identificador, usted debe suscribirse al servicio estándar de nombre/ número disponible con su compañía telefónica. Soluciones para la Batería Si usted experimenta cualquiera de los siguientes problemas, incluso después de haber cargado la batería, usted puede necesitar cambiar el paquete de las baterías.
Cuidado General del Producto Para mantener su aparato funcionando adecuadamente y en buenas condiciones, siga las siguientes pautas: • Evite poner el teléfono cerca de calentadores (calefactores) de ambiente y dispositivos que generen interferencia eléctrica ejemplo, motores o lámparas fluorescentes). • No lo exponga a la luz solar directa o a la humedad. • No deje caer la extensión móvil y no maltrate el teléfono.
Índice A I Acceso Remoto 35 Almacenar Archivos del Identificador de Llamadas (en la Memoria de CID) 26 Almacenar Archivos del Identificador de Llamadas en la Memoria Interna 28 Antes de Comenzar 6 Auto Alerta 18 Idioma 12 Indicador del Sistema Contestador 36 Indicador de Mensajes 33 Información de Interferencias 3 Información Sobre la Aprobación de Equipo 2 Instalación 7 Instrucciones Orales 11 Introducción 6 C Cambiar 30 Causas de una Mala Recepción 42 Clave de Área Local 15 Código de Seguridad 13 Cómo
Índice P Para Almacenar un Nombre y Número en la Memoria 29 Para Almacenar un Número de Volver a Marcar 30 Para Alternar entre el Altavoz y el Auricular 22 Para Borrar el Archivo Actual del Identificador de Llamadas 28 Para Borrar Mensajes 34 Para Borrar Todos los Archivos del Identificador de Llamadas 28 Para Cambiar el Código de Seguridad 37 Para Conectar el Auricular Alámbrico 10 Para Conectar el cable de Línea Telefónica 10 Para Conectar la Corriente AC (Eléctrica) 10 Para Contestar una Llamada 17 Para
Garantía Limitada Lo que cubre su garantía: • Defectos de materiales o de trabajo. Por cuánto tiempo después de la compra: • Un año, a partir de la fecha de compra. (El periodo de garantía para unidades arrendadas se inicia con la primera renta o 45 días de la fecha del embarque a la firma de arrendamiento, lo que ocurra primero). Lo que haremos: • Proporcionarle una unidad nueva o, a nuestra opción, una reacondicionada.
Limitaciones sobre la Garantía: • LA GARANTÍA ESPECIFICADA ANTERIORMENTE ES LA ÚNICA GARANTÍA APLICABLE A ESTE PRODUCTO. CUALQUIER OTRA GARANTÍA, EXPRESA O IMPLÍCITA (INCLUYENDO TODAS LAS GARANTÍAS IMPLÍCITAS DE MERCADO O DE SALUD PARA CUALQUIER PROPÓSITO) SON CONSIDERADAS NO VÁLIDAS. NINGUNA INFORMACIÓN VERBAL O ESCRITA OTORGADA POR Thomson Inc., SUS AGENTES, O EMPLEADOS SERÁ CONSIDERADA PARA CREAR UNA GARANTÍA NI PARA AUMENTAR BAJO NINGUNA CIRCUNSTANCIA LA COBERTURA DE ESTA GARANTÍA.
Modelo 27881 00009246 (Rev. 1 Dom S) 07-22 Impreso en China Thomson Inc. 101 West 103rd Street Indianapolis, IN 46290-1102 © 2007 Thomson Inc.