Full Product Manual

ManualsBrandsGE ManualsBell Buttons & Wall PlatesWireless Replacement Doorbell Push Button - White

Push Button Mounting Instructions

NOTE: Avoid mounting on metal surfaces, as it may result in a reduced range of

transmission. Do not mount in an area exposed to direct rain. Push buttons are

typically mounted at the same height as the door knob or handle (between 36” and 44”

above the ﬂoor).

Permanent Mounting Instructions

1. Remove the front cover of the push button (See Figure 1).

2. Before mounting, choose a mounting location that is no further than 150 feet from the

chime unit location. Place the push button where you would like to mount and test with

the chime as close to its ﬁnal location as possible. If it works, continue with mounting the

button. If it does not work, see TROUBLESHOOTING.

3. Hold the back plate of the push button in the selected location with the arrow on the

back of the back plate pointing up.

4. Using the 1/16” drill bit, drill a hole through the back plate of the push button (See

Figure 1-Mounting Hole Locations) and into the surface of the selected location.

5. Secure with the two screws provided.

6. Press front housing onto back cover.

7. Test operation. If chime does not work, see TROUBLESHOOTING.

Temporary Mounting Instructions

1. Clean the mounting location for the push button with a mixture of 50% water and 50%

isopropyl alcohol.

2. Remove protective backing from one side of the adhesive pad and attach it to the back

plate of the push button.

3. Remove protective backing from the other side of the adhesive pad and press the back

plate to the cleaned mounting location with arrow on back plate pointed up. Hold in

place for a few seconds to allow for a secure bond.

Troubleshooting

If the chime does not work:

1. Make sure push button switch is pressed down and held for at least 1 second.

2. Verify battery installation is correct, noting polarity.

3. Try a fresh battery in push button.

4. Make sure chime is no further than 150 feet away from push button.

5. Ensure push button is not mounted on metal, near metal studs, or near the ﬂoor.

6. Try a new location for the chime.

Functional range may be adversely affected by one or more of the following factors:

weather, radio frequency interference, low transmitter battery and obstructions between

the transmitter and receiver.

This device complies with Part 15 of the FCC rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause

undesired operation.

FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by

unauthorized modiﬁcations to this equipment. Such modiﬁcations could void the user’s

authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

For technical support contact Jasco Products Company at 1-800-654-8483

or www.byjasco.com.

Wireless Push Button

Installation Instructions

Required Tools: small ﬂat blade screwdriver, #2 phillips screwdriver and 1/16” drill bit

(not included)

Installing battery in push button

1. Remove the front cover of the push button housing by pushing a ﬂat blade screwdriver

into the slot at the bottom of the transmitter(See Figure 1).

2. Install the CR2032 battery (included) with the positive (+) side up.

3. Keep the front cover off the push button until melody selection is complete.

Pairing the transmitter push button(s) to receiver

1. Locate the pairing button on the chime (receiver).

2. Press and hold the pairing button. You will hear the “Ding Dong” melody twice, and then

the double beep to alert you the chime is ready to pair with the push button. Release the

pairing button.

3. Press and release the push button (See Figure 1 for push button location). You will hear

one beep letting you know the chime accepted the signal.

4. Wait 10 seconds and you will hear the double beep again to alert you the push button is

now paired with the chime (receiver).

5. Press the push button to test.

6. If the chime receiver does not sound, repeat Steps 1-4 again.

Melody Selection Setting (your chime will have either 2 or 8 melodies)

Select the melody by pushing the Melody Selection Button located inside the push button

housing (See Figure 1). Press and release the Melody Selection Button until you hear the

desired melody. Table 1 and Table 2 shows the order the melodies will be heard.

The last melody played will be your selected chime melody.

19249_19301 v3

6/16/2017

Push Button (Transmitter) Figure 1

Push

button

Mounting

hole

locations

Battery

compartment

Melody

selection

button

Push

button

Push flat blade screwdriver into

the slot to open the cover

Table 2 - 8 Melody Chime

1 Dingdong

2 Westminster

3 Knocks (3 times)

4 Fanfare

5 Mozart

6 Good Vibes

7 Patriotic

8 Tango

Table 1 - 2 Melody Chime

1 Dingdong

2 Westminster

IMPORTANT: This GE push button is compatible with GE door chimes

purchased after May 2013.

If your door chime was purchased before May 2013, please contact Jasco

Products Company at 1-800-654-8483 for further assistance.

CAUTION

• BATTERIES MAY LEAK HARMFUL

LIQUIDS OR IGNITABLE

MATERIALS OR EXPLODE

CAUSING INJURY AND

PRODUCT DAMAGE

• DO NOT MIX OLD AND NEW

OR OTHER BATTERY TYPES

• REPLACE ALL BATTERIES AT

THE SAME TIME

• REPLACE EXHAUSTED BATTERIES

IMMEDIATELY

• REMOVE BATTERIES IF PRODUCT

IS TO BE UNUSED FOR

EXTENDED PERIOD OF TIME

MADE IN CHINA

GE is a trademark of General Electric Company and is under

license by Jasco Products Company LLC, 10 E. Memorial Rd.,

Oklahoma City, OK 73114.

This Jasco product comes with a 90-day limited warranty.

Visit www.byjasco.com for warranty details.

Questions? Contact us at 1-800-654-8483 between

7:00AM—8:00PM CST.

Summary of content (2 pages)

PAGE 1
Push Button Mounting Instructions NOTE: Avoid mounting on metal surfaces, as it may result in a reduced range of transmission. Do not mount in an area exposed to direct rain. Push buttons are typically mounted at the same height as the door knob or handle (between 36” and 44” above the floor). Wireless Push Button IMPORTANT: This GE push button is compatible with GE door chimes purchased after May 2013.
PAGE 2
Botón pulsador de timbre inalámbrico Instrucciones de montaje del pulsador NOTA: Evite el montaje en superficies metálicas, ya que puede dar lugar a una reducción en el alcance de la transmisión. No monte en una zona expuesta a la lluvia directa. Los pulsadores se montan típicamente a la misma altura de la perilla o manija de la puerta (a una distancia entre 36 pulg. y 44 pulg. del suelo). IMPORTANTE: este botón pulsador GE es compatible con timbres para puertas GE adquiridos después de mayo de 2013.