45235 Home Monitoring B/W Wireless Camera System with Monitor User Manual www.jascoproducts.
Thank you for purchasing the GE 45235 B/W Wireless Camera System with Monitor. Please review these instructions carefully before attempting to operate the unit. PRODUCT FEATURES • “Wi-Fi” internet friendly wireless system—won’t interfere with home wireless networks • View up to two cameras automatically • Audio Detection & Notification feature—alerts when sound is detected in a monitored area • Night Vision feature for low or no light viewing up to 10 ft.
1. 45235B/W Wireless Camera 2. 45235 5.5” B/W CRT monitor 3. Wall mounting hardware 4. 2 AC adapters BEFORE YOU INSTALL When choosing the best location for the placement of the camera and monitor, it is best to avoid any sources of possible RF interference such as microwave ovens and cordless phones. Proximity to these and other sources of RF interference can inhibit the proper functioning of the receiver.
• Do not use in wet locations. If using outside, position camera in a sheltered location. • Do not position the camera so that it points directly into the sun or any bright light, as this may cause damage to the camera. • Avoid viewing areas where half the area is in bright sunlight and the other half is dark, such as in the shadow of a building. All types of cameras have difficulty “seeing” into areas of such divergent light levels.
CONNECTING TO THE MONITOR Before beginning installation, we recommend that you temporarily “connect” the 45235 B/W Wireless Camera to the 5.5” Monitor to help familiarize yourself with the camera system and select the best location for installing the camera. The camera connects wirelessly and automatically to the monitor when both are powered on and within 200 ft. of each other (unobstructed view). This system will accommodate up to 2 cameras.
Monitor controls – 1 2 setting (1 or 2) located on Channel the unside of the camera Selection switch housing. (See Channel Selection.) 4. Brightness/Contrast and Vertical Hold can be adjusted with controls at the back of the monitor. + – BEEP 13.5V 1.2A Audio Out + TRIGGER Video Out 1 2 1/2 V-HOLD BRIGHT CONT CHANNEL Channel Selection switch CHANNEL SELECTION Manual Mode To select one of the two channels manually, press the MANUAL button on the front panel of the Monitor.
Multi-Camera Operation This wireless surveillance system is designed to work with up to 2 cameras. Additional cameras are sold separately. IMPORTANT: When using more than one camera, each camera must be assigned to a specific channel using the channel selection switch located on the underside of the camera housing. Select either 1 or 2 for each camera. Each camera must be assigned to a specific channel; both cameras cannot be on the same channel or the signals will cancel out.
to 1/2 position. Next, press the AUTO button on the front panel of the Monitor. The green LED will light and the Monitor will automatically select between the two active cameras. The monitor will display images from both cameras alternately. Cycle Time Setting (Time interval between camera selections) The default cycle time for the receiver is preset to 4 seconds. To change the cycle time, press both of the buttons (Auto/Manual) on front of the receiver simultaneously. The Monitor will beep.
enough light, color will return to the images. Infra-Red (IR) LEDs AUDIO DETECTION AND NOTIFICATION FEATURE This feature allows the system Sensor to emit an audio alert whenever sound is detected within a monitored area. When the camera detects a sound, the receiver will sound an alert and ‘Alarm’ light on the front of the Monitor will flash.
Desktop Mount: 1. Place camera in desired location on a flat surface. SE N I SI T VI TY MAX 2. Set Channel switch on camera to 1 or 2. MIN 3. Reconnect AC adapter to the camera and power on the monitor. Antenna pivots to 4. Adjust antenna and camera increase/decrease angle as needed for the clearest signal strength picture. Positioning the antenna upwards to improve transmission distance, and downwards to reduce transmission. Take care not to force the antenna past its lock positions.
3. Set Channel switch on camera to 1 or 2. Slide the camera onto the alignment and locking pins of the mounting plate. 4. Adjust antenna and camera angle as needed for the clearest picture. USING THE 45235 B/W WIRELESS CAMERA MONITOR SYSTEM WITH A VCR You can connect the 45235 Monitor to a VCR, DVR or another monitor in order to VCR record/view the images received from up to 2 Video In Audio In cameras.
AC adapter charges the battery Wall or desktop mount OPTIONAL WIRELESS BATTERY PACK AVAILABLE (SOLD SEPARATELY) Rechargeable NiMH Battery is available for use with the 45235 Wireless B/W Camera. This 850mAh battery will power the wireless Camera for approximately 5 hours on a single charge. To order this battery, please visit www.jascoproducts.com/ batteryoffer or call our Customer Support department at 1-800-654-8483, Monday–Friday 8 a.m.–5 p.m. CST.
No camera picture 1. Check all connections. Make sure camera(s) and receiver are powered ON. 2. Ensure camera(s) and receiver are set to correct channel(s). 3. Make sure camera is within range of receiver. 4. Adjust the antennas of the monitor and camera(s). Blank monitor 1. Make sure receiver or monitor is switched ON, and the correct video input has been selected 2. If using AC adapter, make sure it is plugged in. 3. If using a battery, make sure it is installed correctly, and is fully charged.
5. Adjust the antennas of the monitor and camera(s). Audio problems 1. Ensure the volume is turned up sufficiently on the Monitor (or TV). 2. Make sure the sound is within the microphone range. 3. If the unit emits a loud wailing sound (feeds back), try moving the camera away from the monitor or angle the monitor in a different direction. SPECIFICATIONS (Subject to change without notice.) CAMERA TV System ..................................................................................................
Current Consumption ......................................................Approx. 800 mA Output .............................................................................................Audio/Video Overall Size.........................................................5.7” W x 7.28” H x 8.46” D WARRANTY ONE-YEAR LIMITED WARRANTY: Jasco Products Company warrants this product to be free from manufacturing defects for a period of one year from the original date of consumer purchase.
FCC STATEMENT NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.