45601 Wireless Lighting Control Advanced Remote LCD remo CONTROL SmartHome 18 ™ • Individual Z-Wave devices • Groups* • Lighting scenes** Control up to 232 Z-Wave enabled devices. *A group turns multiple lights on/off at the same time. **A scene dims or brightens lights in multiple areas to suit your mood.
INTRODUCTION Thank you for purchasing the GE 45601 Advanced Remote. This remote allows you to control up to 18 individual Z-Wave devices with one easyto-use, compact unit. You can also set up and control up to 18 groups of lights as well as 18 scenes for task or mood lighting. Groups can include up to 232 Z-Wave devices and each scene can include up to 32 Z-Wave devices. Lights can be included in multiple groups.
lights from different groups. Your Z-Wave home control network can include up to 232 Z-Wave enabled devices. Additional features include: - Easy to use LCD menu system - Event programming which allows you to set timed events such as turning on all of your lights at a certain time every day. - Control of a Z-Wave enabled thermostat for your HVAC system.
If this remote is used as the primary controller, you must use it to create your control network. You can use multiple remote controls with your Z-Wave lighting control network, however, only one remote will act as the primary controller. The primary controller must be used to add or delete devices (lights / nodes) from your network.
Scene: A scene lets you establish preset brightness levels for multiple Z-Wave controlled lights and then control them with one command. This is ideal for mood or task lighting. Scene 1 could be the family room lights set to dim for watching TV. Scene 2 could have the same lights set to a different brightness level for other activities like reading or entertaining. Event: An event is something you want to happen at a specific time and day.
WIRELESS RANGE This device complies with the Z-Wave standard of open-air, line of sight transmission distances of 100 feet. Actual performance in a home depends on the number of walls between the remote controller and the destination device, the type of construction and the number of Z-Wave enabled devices installed in the control network. Every Z-Wave enabled device acts as a signal repeater and multiple devices result in more possible transmission routes which helps eliminate “RF dead-spots”.
Please Note: Z-Wave home control networks are designed to work properly alongside 802.11 wireless computer networks, Bluetooth and other 2.4GHz or 5.8GHz devices. Some baby cams, wireless video devices and older cordless phones using the 900MHz frequency range may cause interference and limit Z-Wave functionality. Many 900MHz products have a switch to select channel “A” or “B”. You may find that one of these channels will cause less interference than the other. NOTES ON NETWORK MANAGEMENT 1.
5. Press a digit (1-9) for the device location you wish to add. Press SETUP (SHIFT) and the digit (1-9) if you are adding devices 10 through 18. 6. Press OK and the screen will display SETUP WAITING. 7. Press the button on the device so that it communicates with the remote. 8. When the screen displays SUCCESS, you have successfully added the device to the number key and your network. CONTROLLING INDIVIDUAL LIGHTS (DEVICES / NODES) You can control a light to turn on or off, or change its brightness level.
DELETING A DEVICE (LIGHT / NODE) FROM YOUR NETWORK This completely removes the device from your home control network and resets the device to its factory default settings. 1. Press and hold SETUP until screen displays LGHT SETUP 2. Press OK followed by pressing the cursor right key 2 times the screen will display DELETE. 3. Press OK. 4. Press the button on the device so that it communicates with the remote. 5. When the screen displays SUCCESS, you have successfully deleted the node/light from your network.
4. Press the OK key and the screen will display SEL DIGIT. 5. Press a digit (1-9) for the group you wish to remove the device from. Press SHIFT and the digit (1-9) if you are removing a device from groups 10 through 18. 6. Press the OK key and the screen will display SETUP WAITING. 7. Press the button on the device you wish to remove. 8. When the screen displays SUCCESS, you have successfully removed the device. Deleting a Group: This only deletes the specific group.
Removing a Light (Device / Node) from a Scene: This only removes the device from a specific scene. The device is still part of your home control network and the scene still exists (if there were more than one device in it to start). 1. Press and hold SETUP until screen displays LGHT SETUP. 2. Use either Arrow key to scroll until the display reads SCN SETUP. 3. Press OK followed by either Arrow key until the display reads REMOVE. 4. Press OK and the screen will display SEL DIGIT. 5.
To turn all devices on or off, perform the following steps: 1. Press ALL once. The screen will display ALL. 2. Press either ON or OFF. Any ON or OFF button can be pressed. (The screen will display ALL ON or ALL OFF depending on what key was pressed). Adding Devices (Lights / Nodes) to All Control: 1. Press and hold SETUP the screen displays LGHT SETUP. 2. Use either Arrow key to scroll until the display reads ALL SETUP. 3. Press OK and screen will display EX ON/OFF. 4.
events such as turning on or off your lights at a preset time and day. You must set the time and date before programming an Event. Adding an EVENT: 1. Press and hold SETUP until the screen displays LGHT SETUP. 2. Use either Arrow key to scroll until the display reads EVENTS. 3. Press OK and the Screen will display ADD. 4. Press OK and the Screen will display EVERY DAY. Use Either Arrow key to change this option to MON-FRI, SAT-SUN, ONE TIME or a specific Day of the WEEK. 5.
THERMOSTATS Adding a Thermostat: The 45601 Advanced Remote allows you to program and control a Z-WAVE enabled Thermostat. 1. Press and hold SETUP until screen displays LGHT SETUP. 2. Use either arrow key to scroll until the screen displays THERMOSTAT. 3. Press OK and the screen will display ADD. 4. Press OK and the screen will display SETUP WAITING. 5. Press the button on the thermostat’s Z-Wave interface. 6.
6. Use either Arrow key to scroll until the display reads the proper number of bytes (1, 2 or 4) as indicated in the Z-Wave. device’s instructions. 7. Press OK and the screen will display read CONFIG VAZL. 8. Use either Arrow key to scroll until the display reads the proper value (0 - 255) as indicated in the Z-Wave device’s instructions. 9. Press OK. 10. Press the button on the device. 11. The screen will display SUCCESS.
PRIMARY CONTROLLER SHIFT (TRANSFER) You can transfer all of the 45601’s information to another remote, so it becomes the new primary controller. The 45601 will retain all of its programming; however, it will now be a secondary controller. Transferring Primary Controller Information: 1. Place the two remotes near each other. 2. On the 45601, press and hold SETUP until the screen displays LGHT SETUP. 3. Use either Arrow key to scroll until the display reads TRANSFER. 4.
Interoperability with Z-Wave® Devices A Z-Wave® network can integrate devices of various classes, and these devices can be made by different manufacturers. Although every Z-Wave certified product is designed to work with all other Z-Wave certified products, your controller must include the appropriate device classifications in order to control non-lighting Z-wave devices. As an example, the 45600 basic remote is designed only for controlling Z-Wave devices using the lighting control classification.
WARRANTY JASCO Products warrants this product to be free from manufacturing defects for a period of two years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. This warranty is in lieu of all other warranties, expressed or implied.
is a registered trademark of General Electric Company and is used under license to Jasco Products Company LLC, 10 E Memorial Rd., Oklahoma GE SmartHome City, Oklahoma 73114 Made in China Hecho en China ™ All brand names shown are trademarks of their respective owners. Todas las marcas que aparecen aquí son marcas registradas de sus respectivos dueños.