Instructions / Assembly

1 5 0 LIGHTS
IMPORTANT SAFETY INSTRUCTIONS
When using electric products, basic precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1. Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When
products are used in outdoor applications, connect the product to a Ground Fault Circuit
Interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
2. This seasonal use product is not intended for permanent installation or use.
3. Do not mount or place near gas or electric heater, fireplaces, candles or other similar sources of heat.
4. Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
5. Do not let lamps rest on the supply cord or on any wire.
6. Unplug the product when leaving the house, when retiring for the night, or if left unattended.
7. This is an electric product-not a toy! To avoid risk of fire, burns, personal injury and electric shock, it
should not be played with or placed where small children can reach it.
8. Do not use this product for other than its intended use .
9. Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
10.Do not hang ornaments or other objects from cord, wire, or light string.
11.Do not place lighting string on carpeting, drapes, furniture, or allow it to contact vinyl siding while the power is on.
12.Do not perform any maintenance or troubleshoot for bad or broken lamps while the power is on.
13.Do not cover the product with cloth, paper, or any material not part of the product when in use.
14.This product is equipped with push-in type lamps. Do not twist lamps.
15.This product employs overload protection (fuse). A blown fuse indicates an overload or short -circuit
situation. If the fuse blows, unplug the product. Replace the fuse as per the user servicing
instructions(follow product marking for proper fuse rating) and check the product.
If the replacement fuse blows, a short-circuit may be present and the product should be discarded.
16.Read and follow all instructions that are on the product or provided with the product.
SAVE THESE INSTRUCTIONS
USE AND CARE INSTRUCTIONS
1. When the product is placed on a live tree, the tree should be well maintained and fresh. Do not place on
live trees in which the needles are brown or break off easily. Keep the tree holder filled with water.
2.
If the product is placed on a tree, the tree should be well secured and stable.
3.
Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or frayed wire
insulation or cords, cracks in the lamp holders or enclosures, loose connections, or exposed copper wire.
4.
When storing the product, carefully remove the product from wherever it is placed, including trees, branches,
or bushes, to avoid any undue strain or stress on the product conductors, connections, and wires.
5.
When not in use, store neatly in a cool, dry location protected from sunlight.
USER SERVICING INSTRUCTIONS
FUSE REPLACEMENT
Most often, fuses blows because too many sets have been string end-to-end.
1.
Before changing fuses, make sure the set is unplugged.
2. Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.
3. Using a flathead screwdriver, open fuse cover. Slide open fuse access cover on top of attachment
plug towards blades. (See diagram)
-SEE OTHER SIDE-
-CONTINUED FROM OTHER SIDE-
4. Remove fuses carefully . Turn plug over to empty fuse compartment.
5.
Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse (provided with product).
6. Close fuse cover. Slide closed the fuse access cover on top of the attachment plug. Make sure door is closed and fuses are completely covered.
7. Risk of fire. Do not replace attachment plug. Contains a safety device (fuse) that should not be removed. Discard
product if the attachment plug is damaged.
BULB REPLACEMENT: Before changing bulbs, make sure set is unplugged.
CAUTION: This string contains two different types of Replaceable bulbs- steady-illuminating and fuse bulbs. REPLACEABLE
FUSED LAMPS-identified by the white (or green) colored ring on the lamp base. There is one fuse bulb for each lighted circuit of 50 bulbs.
Always replace burned-out bulbs promptly. If a number of bulbs are burned out, extra stress is put on the remaining bulbs in the circuit. This
may cause additional bulbs to burn out prematurely. When a fuse bulb fails the entire circuit will not light.
NOTE: Steady and Fuse bulbs are not interchangeable.
Replace Steady Bulb
If the spare bulbs provided with the product have no plastic base or the plastic
base does not fit, first follow steps 1-2 above. Then:
a) Remove the old bulb by straightening the bulb wires and pulling bulbs
straight from the base..
b) Replace the new bulb by straightening the bulb leads and aiming each
wire into a separate hole in the plastic base.
c) Make sure each bulb lead comes out an exit opening at the bottom of the plastic base. Now bend each lead up such that
each bulb lead fits closely against the narrow side of the plastic base.
Replace Fuse Bulb
NOTE: Fuse bulbs are secured in the base with adhesive. Do not attempt to remove old fuse bulb and replace with 2.5 Volt, 0.425 Watt fuse bulbs
provided with product.
CAUTION: 1. This lighting string is rated 150L, 61.2 Watts (0.51Amps), do not overload. Connect other lighting strings or decorative outfits
end-to-end up to a maximum of 21 6 Watts (1. 8 Amps) total.
If connecting to a Lighting String that does not have a Wattage (W) rating,{found on the cord tag within 6 inches of the plug}, calculate the wattage as
follows: Multiply the current (
A), which is also on that cord tag, by 120.
For example: The Lighting String is rated 120V, 60Hz, 0.2 Amps 0.2x120 = 24 Watts.
Add the wattage of each light string together for a total of 21
6 Watts or less. (Do not exceed 21 6 Watts.)
2. To reduce the risk of overheating, replace burned out lamps promptly. Use 2.5 Volt ,0.425 Watt lamps only.
3 . To reduce the risk of fire electric shock: a)Do not install on trees having needles, leaves or branch coverings of metal or materials that look like metal,
and b)Do not mount or support strings in a manner that can cut or damage wire insulation.
WARNING: Risk of fire. This product employs overload protection(fuse bulb) in each series circuit to provide overload protection in addition
to the fuse(s) located in the plug. Do not replace the fuse bulb contained in this set with any other type of bulbs. Use only spare fuse bulbs provided with
this product.
For questions and/or assistance, call customer service at 1-877-398-7337 or visit us on the web at www.GEholidaylighting.com
FOR INDOOR AND OUTDOOR USE E238369 HC-14
Printed In China 120 VOLTS MADE IN CHINA
©2014 Nicolas Holiday Inc., 9F., No. 37, Guangfu N. Rd Taipei, Taiwan 10560.All rights reserved
MODEL NO.
FPS-150/3F(0.51)
St
ep
1
:
G
rasp p
l
ug an
d
remove
f
rom
th
e
receptacle or other outlet device. Do not unplug
by pulling cord.
Step 2:Hold bulb by the plastic base and pull
bulb/base straight out of socket.
St
ep
3
:
R
ep
l
ace
l
amp w
ith
on
l
y
2
.
5
V
o
lt
,
0
.
425
Watt super brightness midget push-in type lamp
provided with product.
Push spare bulb/base assembly into socket. Do
not twist bulb when inserting into socket. If bulbs
are twisted, part of the set will not light.
a
b
c