JGRP20 Install

ManualsBrandsGE ManualsOven24 in. Single Gas Wall Oven Self-Cleaning in White

BEFORE YOU BEGIN

Read these instructions completely and carefully.

IN THE COMMONWEALTH OF

MASSACHUSETTS:

This product must be installed by a licensed

plumber or gas fitter.

When using ball-type gas shut-off valves, they shall

be the T-handle type.

A flexible gas connector, when used, must not

exceed 3 feet.

IMPORTANT — Save these instructions

for local inspector’s use.

IMPORTANT — Observe all governing

codes and ordinances.

IMPORTANT — Leak testing of the

appliance shall be conducted according to the

manufacturer’s instructions.

Note to Installer – Be sure to leave these

instructions with the Consumer.

Note to Consumer – Keep these instructions for

future reference.

Skill level – Installation of this appliance requires

basic mechanical skills.

Completion time – 1 to 3 hours

Proper installation is the responsibility of the

installer.

Product failure due to improper installation is not

covered under the Warranty.

WARNING

This appliance must be properly

grounded.

FOR YOUR SAFETY

WARNING

If the information in this manual is

not followed exactly, a fire, explosion or gas leak may

result, causing property damage, personal injury or

death.

DO NOT STORE OR USE GASOLINE OR OTHER

FLAMMABLE VAPORS AND LIQUIDS IN THE

VICINITY OF THIS OR ANY OTHER APPLIANCE!

WHAT TO DO IF YOU

SMELL GAS:

Do not try to light any appliance.

Do not touch any electrical switch; do not use any

phone in your building.

Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

If you cannot reach your gas supplier, call the fire

department.

Installation and service must be performed by a

qualified installer, service agency or the gas supplier.

Be sure your oven is installed properly by a

qualified installer or service technician.

Be sure the oven is securely installed in a cabinet

that is firmly attached to the house structure.

Weight on the oven door could cause the oven to

tip, resulting in serious personal injury or death.

Never allow anyone to climb, sit,

Installation

Instructions

24” Gas Built-In Oven

JGRP20

If you have questions, call GE Appliances at 800.GE.CARES (800.432.2737) or Visit our Website at:

GEAppliances.com.

31-2000792 Rev. 0 07-20

Summary of content (20 pages)

PAGE 1
Installation Instructions 24” Gas Built-In Oven JGRP20 If you have questions, call GE Appliances at 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com. BEFORE YOU BEGIN Read these instructions completely and carefully. IN THE COMMONWEALTH OF MASSACHUSETTS: Ŷ This product must be installed by a licensed plumber or gas fitter. Ŷ When using ball-type gas shut-off valves, they shall be the T-handle type. Ŷ A flexible gas connector, when used, must not exceed 3 feet.
PAGE 2
Installation Preparation TOOLS YOU WILL NEED 1 GAS REQUIREMENTS Safety Glasses Drill with 1/8” Bit Ruler Adjustable Wrench Pencil Pipe wrench 3/16” Hex Socket Driver #1 or #2 Phillips Screwdriver 12” Spirit Level Hand Saw MATERIALS YOU MAY NEED Gas line shut-off valve Pipe joint sealant 1/2” pipe nipple FOR FLEXIBLE CONNECTION WHERE LOCAL CODES PERMIT: • Coated and approved flexible metal tubing (same Ǝ RU Ǝ , ' DV JDV VXSSO\ OLQH • Adaptor or connector You must follow local codes when
PAGE 3
Installation Preparation Ǝ ZLGWK Ǝ KHLJKW Ǝ PLQ RQ HLWKHU VLGH 6HH )LJ The cabinet must have solid sides, back and bottom. The bottom must be solid either at floor level or with the bottom edge of the cutout. Any openings around the gas or electrical outlets must be sealed. All cabinet openings must be sealed at the time of installation to prevent drafts. Drafts will affect safe use of the oven. It’s best to use a template to make a straight cut.
PAGE 4
Installation Instructions INSTALL THE OVEN 4 ELECTRICAL CONNECTIONS 5 GAS CONNECTIONS An adequate electrical supply and outlet must be used to operate the electrical parts of your oven. WARNING Do not operate the burners of A. The oven cord has a three-prong plug and must be used with a properly grounded three-hole outlet with a standard 120 Volt, 60 cycle AC household current. this oven when using LP (bottled) gas before converting the pressure regulator and burner orifice for LP gas usage. B.
PAGE 5
Installation Instructions 5 GAS CONNECTIONS (Cont.) 6 CHECK FOR LEAKS I. Place the oven in the cutout. J. Level the oven: 1. Place a spirit level on one of the oven racks. 2. If the oven is not level, adjust the leg levelers. 3. Remove regulator cover at the back of the storage drawer area by removing 4 screws. With the oven in place, the pressure regulator inlet is accessible through the opening in the main back. K. Through this opening connect: 1.
PAGE 6
Installation Instructions INSTALL THE OVEN (Cont.) 8 CHECK THE BURNER FLAMES FOR NATURAL GAS 9 MAKE THE BURNER FLAME ADJUSTMENTS (Cont.) The oven is factory-adjusted for use with Natural Gas in most areas. But, since the gas in some areas may vary, you should check all adjustments described below. If you are to use LP Gas, see LP Adjustments at the back of this guide. NOTE: Bake and broil flame must be checked with the door closed to properly check flame characteristics.
PAGE 7
Installation Instructions 10 SECURE THE OVEN IMPORTANT: Remove all packing material and literature from the oven before connecting any electrical supplies. A. Using a 1/8” drill bit, drill holes through the side trim and into the cabinet front. 11 RECHECK STEPS Double check to make sure everything in this guide has been completed. Rechecking steps will ensure safe use of the oven. WARNING The trim permits air entry into the cabinet below the unit and must not be blocked. B.
PAGE 8
Installation Instructions MAKE THE LP GAS CONVERSION WARNING If you are using LP (bottled) gas, all the adjustments described below must be made before you make any burner adjustments or use the oven. WARNING This conversion must be performed by a qualified installer or gas supplier in accordance with the manufacturer’s instructions and all codes and requirements of the authority having jurisdiction. Failure to follow instructions could result in serious injury or property damage.
PAGE 9
Installation Instructions 3 FOR BAKE AND BROIL BURNERS Use a 1/2” open end or adjustable wrench to turn the orifice hood in the LP direction, about 1-1/2 turns, until snug. 5 ADJUST AIR SHUTTER NOTE: The Bake and Broil burner flame must be checked with the door closed to properly check flame characteristics. Turn on the bake or broil burner. Broil Burner As you watch the flame with the oven door closed, check the following through the oven door window: LP A.
PAGE 10
Installation Instructions MAKE THE LP GAS CONVERSION (Cont.) 5 ADJUST AIR SHUTTER (Cont.) BAKE BURNER 5 ADJUST AIR SHUTTER (Cont.) BROIL BURNER Air Shutter Orifice Fitting Cover A. The broil burner is located and accessible in the top rear of the oven. B. Use a screwdriver to loosen the air shutter adjustment screw. Air Shutter Screw Fig. 19 A. Use a screwdriver to loosen the air shutter screw. 1. If the flames were yellow, open the air shutter more than the original setting. 2.
PAGE 11
Instrucciones de Instalación Horno A Gas Empotrado de 24” JGRP20 ¿Preguntas? Llame al 1.800.GE.CARES (800.432.2737) o bien visite nuestra página Web: GEAppliances.com ANTES DE EMPEZAR: PARA SU SEGURIDAD: Lea estas instrucciones y las advertencias completa y cuidadosamente. ADVERTENCIA Si la información en este manual no se sigue exactamente, podría resultar un incendio, una explosión o un escape de gas que causen daño a la propiedad, heridas personales o muerte.
PAGE 12
Preparación de Instalación LISTA DE HERRAMIENTAS 1 REQUERIMIENTOS DE GAS Gafas de seguridad 7DODGUR FRQ 3XQWD GH Ǝ Llave inglesa ajustable Regla y vara derecha para medir Lápiz Llave inglesa para cañerías Soquete hexagonal 1LYHO GH HVStULWX GH Ǝ Destornillador Phillips No. 1 o No. 2 1LYHO GH HVStULWX GH Ǝ Sierra manual o eléctrica MATERIALES ADICIONALES QUE PODRÍA NECESITAR: Usted debe cumplir con los códigos locales cuando instale su horno.
PAGE 13
Instrucciones de Instalación 3 PREPARE LA ABERTURA (VSDFLR GHO JDELQHWH Ǝ PtQ GH SURIXQGLGDG Ǝ PtQ GH DQFKXUD $EHUWXUD Ǝ GH DQFKXUD Ǝ GH DOWXUD Ǝ PtQ HQ DPERV ODGRV (Vea Fig. 2) Es buena idea usar un molde para hacer un corte derecho. &RORTXH HO PROGH VREUH XQD OtQHD EDVH QLYHODGD Ǝ D Ǝ GHO SLVR (VWR FRORFDUi OD FDYLGDG GHO KRUQR D Ǝ R Ǝ GHO SLVR 24” Min. 24” Min. 22-3/16” 38” 39” 22” to 28” 23-3/4” 2 Soportes &HQWUDGRV D Ǝ Fig.
PAGE 14
Instrucciones de Instalación INSTALACIÓN DEL HORNO 4 CONEXIONES ELÉCTRICAS 5 CONEXIONES DEL GAS Un abastecimiento y receptáculo eléctrico adecuado debe ser usado para operar las partes eléctricas de su horno. ADVERTENCIA No haga funcionar los quemadores A. El cordón del horno tiene un enchufe de tres patas y debe ser usado con un receptáculo de tres hoyos que haga tierra adecuadamente con corriente alterna normal de casa de 120 Voltios, 60 Ciclos.
PAGE 15
Instrucciones de Instalación INSTALACIÓN DEL HORNO (Cont.) 5 CONEXIONES DEL GAS (Cont.) I. Coloque el horno en el corte. J. Nivele el horno: 1. Coloque el nivel de espíritu sobre una de las parrillas del horno. 2. Si el horno no está nivelado, ajuste los niveladores de las patas. 3. Remueva la cubierta del regulador en la parte posterior del área del cajón de almacenamiento, removiendo los 4 tornillos.
PAGE 16
Instrucciones de Instalación INSTALACIÓN DEL HORNO (Cont.) 8 CÓMO REVISAR LAS LLAMAS DE LOS QUEMADORES A GAS NATURAL El horno viene ajustado de fábrica para ser usado con gas natural en la mayoría de las áreas. Pero, como el gas en algunas áreas varía, usted debe revisar todos los ajustes que se describen más abajo. Si usted va a usar gas LP, mire los Ajustes para Gas LP en la parte final de esta guía.
PAGE 17
Instrucciones de Instalación INSTALACIÓN DEL HORNO (Cont.) 10 CÓMO COLOCAR BIEN EL HORNO IMPORTANTE: Saque todos los materiales de empaque y la literature del horno antes de hacer cualquier conexión eléctrica. A. 8VDQGR XQ EDUUHQR GH Ǝ KDJD KR\RV D WUDYpV GH ODV molduras laterales y en el frente del gabinete. 11 REVISE LOS PASOS Revise varias veces para asegurarse que todo en esta guía ha sido completado. El revisar los pasos le asegurará la utilización segura del horno.
PAGE 18
Instrucciones de Instalación CÓMO HACER LA CONVERSIÓN PARA GAS LP ADVERTENCIA Si usted va a usar gas LP 1 AJUSTE EL REGULADOR DE (embotellado), todos los ajustes descritos más abajo deben hacer antes de hacer cualquier ajuste a los quemadores o usar el horno. ADVERTENCIA Esta conversión debe ser hecha por un instalador competente o por el abastecedor de gas de acuerdo con las instrucciones del fabricante y todos los códigos y requerimientos de las autoridades que tienen jurisdicción.
PAGE 19
Instrucciones de Instalación CÓMO HACER LA CONVERSIÓN PARA GAS LP (Cont.) 3 PARA QUEMADORES PARA 5 AJUSTE EL OBTURADOR DE HORNEAR Y ASAR AIRE 8VH XQD OODYH GH Ǝ R XQD OODYH DMXVWDEOH SDUD KDFHU JLUDU la tapa del orificio en dirección de LP, aprox. 1 1/2 vuelta, hasta que quede apretada. Quemador para asar NOTA: Las llamas para hornear y asar se deberían revisar con la puerta cerrada para revisar correctamente las características de la llama. Encienda el quemador para hornear o para asar.
PAGE 20
Instrucciones de Instalación CÓMO HACER LA CONVERSIÓN PARA GAS LP (Cont.) 5 AJUSTE EL OBTURADOR DE AIRE (Cont.) AIRE (Cont.) QUEMADOR PARA HORNEAR Obturador de Aire 5 AJUSTE EL OBTURADOR DE QUEMADOR PARA ASAR Cubierta del Orificio A. El quemador para asar está ubicado y es accesible en la parte superior trasera del horno. B. Use un destornillador para soltar el tornillo del ajuste del obturador de aire. Tornillo del Obturador de Aire Fig. 19 A.