USB 2.0 LR Extender EXT-USB2.0-LR User Manual www.gefen.
ASKING FOR ASSISTANCE Technical Support: Telephone Fax (818) 772-9100 (800) 545-6900 (818) 772-9120 Technical Support Hours: 8:00 AM to 5:00 PM Monday thru Friday. Write To: Gefen Inc. c/o Customer Service 20600 Nordhoff St Chatsworth, CA 91311 www.gefen.com support@gefen.com Notice Gefen Inc. reserves the right to make changes in the hardware, packaging and any accompanying documentation without prior written notice. USB 2.0 LR Extender is a trademark of Gefen Inc. © 2008 Gefen Inc.
CONTENTS 1 Introduction 2 Operation Notes 3 Features 4 Sender Panel Layout 5 Sender Panel Descriptions 6 Receiver Panel Layout 7 Receiver Panel Descriptions 8 Connecting And Operating The USB 2.
INTRODUCTION Congratulations on your purchase of the USB 2.0 LR Extender. Your complete satisfaction is very important to us. Gefen Gefen delivers innovative, progressive computer and electronics add-on solutions that harness integration, extension, distribution and conversion technologies.
OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE USB 2.0 LR EXTENDER • Use industry standard CAT-5, CAT-5e or CAT-6. Gefen recommends using solid core cabling for maximum performance. • The USB 2.0 LR Extender is USB 2.0/1.1 compliant • The USB 2.0 LR Extender can extend USB a maximum of 330 ft (100m) • Use only the AC adapter supplied with the USB 2.0 LR Extender. Use of substitute adapters may cause permanent damage to the system and will void the warranty.
FEATURES Features • Operate USB 2.0 peripherals up to 330ft (100m) from a computer • Supports low and high-speed USB • Uses industry-standard CAT5, CAT5e, or CAT6 cable • Supports all major operating systems -- Windows, MacOS and Linux. • True plug-and-play, 100% hardware solution with no drivers required • Operates at full 480 Mbps speed when running in USB 2.0 mode • Receiver supports up to 2 USB powered connections at 500 mA each • Specifications: Package Includes (1) Gefen USB 2.
SENDER PANEL LAYOUT Front Panel 1 2 3 Back Panel 4 5 6 4 7
SENDER PANEL DESCRIPTIONS 1 Host Connection LED Indicator This LED will become active once a valid connection is made by the host source and the USB 2.0 LR Extender. 2 Power LED Indicator This LED will become active once a valid connection is made between the included 5V DC power supply and an open wall power socket. 3 USB “B” Input Connect the USB source to this input. 4 Link LED Indicator This LED will become active once a valid connection is between the sender and receiver units.
RECEIVER PANEL LAYOUT Front Panel 1 2 3 4 Back Panel 5 6 7 6 8
RECEIVER PANEL DESCRIPTIONS 1 Host Connection LED Indicator This LED will become active once a valid connection is made by the host source and the USB 2.0 LR Extender. 2 Power LED Indicator This LED will become active once a valid connection is made between the included 5V DC power supply and an open wall power socket. 3 USB “A” Input 1 Connect the USB device to this input. 4 USB “A” Input 2 Connect the USB device to this input.
CONNECTING AND OPERATING THE USB 2.0 LR EXTENDER How to Connect the USB 2.0 LR Extender 1. Connect the USB source to the USB 2.0 LR Extender sender unit using the supplied USB A to B cable. 2. Connect up to two USB peripherals to the USB 2.0 LR Extender receiver using user supplied USB cables. NOTE: Powered USB hubs may be connected to these ports up to a maximum connection of 14 USB peripherals (including hubs). 3. Connect the USB 2.
TROUBLESHOOTING Using the Led Indicators to Troubleshot Issues Power LED The power LED indicators should be active once the included 5V DC power supply has been properly connected between the sending/receiving unit and an open wall power socket. A non-active LED can indicate a power problem. Please check that the power cable is properly connected and locked to the sender/receiver unit.
NETWORK CABLE WIRING DIAGRAM Gefen has specifically engineered their products to work with the TIA/EIA-568-B specification. Please adhere to the table below when field terminating cable for use with Gefen products. Failure to do so may produce unexpected results and reduced performance. Pin Color 1 Orange / White 2 Orange 3 Green / White 4 Blue 5 Blue / White 6 Green 7 Brown / White 8 Brown 12345678 CAT-5, CAT-5e, and CAT-6 cabling comes in stranded and solid core types.
WIRING DIAGRAM 11
SPECIFICATIONS USB 2.0 Speed ....................................................................................... 480 Mbps Link Connectors ............................................................................. RJ-45 Shielded USB Connectors Transmitter: ........................................................ (1) USB type B USB Connectors Receiver: ............................................................. (2) USB type A Dimensions Transmitter: ...................................................
WARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen is notified within two (2) years from the date of shipment, Gefen will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifications.
*ma-USB2.0-LR* Rev X1 20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 www.gefen.com fax: 818-772-9120 support@gefen.