Technical Manual

H-100 CONNECTOR PIN DESCRIPTIONS
J1 Wire Signal Description J2 Wire Signal Description
1 CAN (rtn) CAN Bus 1 391 RS485 (-) Diagnostic/Rem-An/HTS
2 CAN (+) CAN Bus (+) 2 388 RS232 (tx) GenLink
3 810 Gnd Modem Power (-) 3 IN7 IN (DB) 7 DI-3/Line Power
4 805 AN8 (rtn) Emissions Sensor/ 4 183 IN (DB) 4 Remote Start
Fluid Basin Level
5 804 AN8 (+) 0-1V Emissions Sensor/ 5 174 IN (DB) 1 Key Switch in AUTO
Fluid Basin Level
6 575R AN5 (rtn) Fuel Level 6 224 Vsense 1 Phase AB Voltage
7 575V AN5 (+) 4-20mA Fuel Level 7 227 Gnd Vsense PCB Ground
8 523R AN1 (rtn) Oil Temperature 8 403 OUT (OC) 14 AVR Gate trigger ‘B’
9 523V AN1 (+) 4-20mA Oil Temperature 9 399C CT3 (-) Phase C Current
10 R15B OUT (OC) 10 Overspd Shutdown 10 398C CT3 (+) Phase C Current
11 256 OUT (OC) 2 Fuel Relay 11 399A CT1 (-) Phase A Current
12 0 - Batt (12/24V) Panel Power (-) 12 398A CT1 (+) Phase A Current
13 CAN (-) CAN Bus (-) 13 390 RS485 (+) Diagnostic/Rem-An/HTS
14 811 IN (DB) 9 Modem DCD 14 387 RS232 (rx) GenLink
15 68V AN2 (+) 4-20mA Coolant 15 567/601 IN (DB) 6 DI-2/Ruptured Basin/
Temperature Low Fuel Pressure
16 803 AN9(+) 0-5V Battery Charger Cur 16 R15 IN (DB) 3 Emergency Stop
17 766R AN7 (rtn) Throttle Position 17 226 Vsense 3 Phase CA Voltage
18 766V AN7 (+) 4-20mA Throttle Position 18 +12V (500 mA) Vsense PCB
19 69R AN3 (rtn) Oil Pressure 19 405 Gnd AVR PCB Power (-)
20 69V AN3 (+) 4-20mA Oil Pressure 20 404 OUT (OC) 13 AVR Gate trigger ‘A’
21 221/808 OUT (OC)12 (PWM) Preheat/Air 21 OC8 OUT (OC) 8 Auxiliary 4 Output
/Fuel Solenoid
22 242 OUT (OC) 4 13.3 Gas Relay 22 OC6 OUT (OC) 6 Auxiliary 2 Output
23 56A OUT (OC) 1 Starter Relay 23 OC5 OUT (OC) 5 Auxiliary 1 Output
24 0/shld RPM sensor (-) Engine RPM 24 SHLD RS485 (shield) Diagnostic/Rem-An/HTS
25 79 RPM sensor (+) Engine RPM 25 389 RS232 (com) GenLink
26 812 IN (DB) 10 Modem Enable 26 IN8 IN (DB) 8 DI-4/Generator Power
27 AI1R/806/ AN6 (rtn) Fuel Press/Ign. Alarm/ 27 505 IN (DB) 5 DI-1/Battery Charger Fail
754R Inlet Temp
28 AI1S/ AN6 (+) 4-20mA Fuel Press/ 28 175 IN (DB) 2 Key Switch in MANUAL
754V Inlet Temp
29 573R AN4 (rtn) Coolant Level 29 225 Vsense 2 Phase BC Voltage
30 573V AN4 (+) 4-20mA Coolant Level 30 406 AVR Zero Crossing AVR Zero Crossing Input
31 68R AN2 (rtn) Coolant Temp 31 194 +12V (300 mA) AVR PCB Power (+)
32 809 +12V (300mA) Modem Power (+) 32 OC9/25 OUT (OC) 9 13.3 Ignition Power
33 769 OUT (OC)11 (PWM) Throttle Driver 33 OC7 OUT (OC) 7 Auxiliary 3 Output
34 445 OUT (OC) 3 Fault Relay 34 399B CT2 ( - ) Phase B Current
35 15B/220B + Batt ( 12/24V ) Panel Power ( + ) 35 398B CT2 ( + ) Phase B Current

KEY:
OUT (O/C) #1-14 = Digital OUTput, Open Collector (includes
PWM Outputs, AVR Gates)
IN (DB) #1-10 = Digital INput, Buffered (Schmitt Trigger)
“Pulled up”
AN #1-7 (+) = Analog 12V ( 50 mA ) source
AN #1-7 (rtn) = General purpose analog input ( 4 - 20 mA )
Vsense #1-3 = Voltage sensing input ( 0 - 28.8 VAC)
CT #1-3 = Current Transformer input ( 0 - 3 A AC)
46
Appendix B
H-100 Control Panel Technical Manual