Manual

SPECiFiCATiONS
EngineType........................ SingleCylinder,4-Stroke
EngineSize....................................... 80c0
StarterType...................................... Recoil
FuelCapacity/Type................. 0.73 Gal(2.77 L)/Unleaded
OilCapacity................................ 0.03 Qt (O.TL)
RuntimeFull/HalfLoad........................ 2.5/5.0 Hours
SparkPlugType................................. BPR7HS
SparkPlugGap..................................... 030"
DimensionsLx Wx H (in)...................... 22x 12x 18
WeightLb/kg................................. 46.0/20.09
MaximumACOutput.............................. 1400W
SurgeACOutput................................. 1450W
ACVolts....................................... 120VAC
RatedACCurrent.................................. 11.6 A
Frequency....................................... 60 Hz
THD............................................. 3.0%
InsulationClass.................................. ClassB
Outlets.............................. (2) 5-15R,(1) 12VDC
DCVolts........................................ 12VDC
RatedDCCurrent.................................... 5 A
NOTE:
Power output and runtime are influenced by many factors,
someof whichare fuel quality, ambienttemperatureand engine
condition.Outputdecreases approximately 3.5% for each 1,000
feet abovesea level and 1% for every 10 degrees above60°F.
EMISSIONSINFORMATION
The Environmental Protection Agency (EPA) and California Air
Resource Board(CARB) requirethat your generatorcomply with
exhaust and evaporativeemission standards. This generator is
certified to meet the applicable EPAand CARBemission levels.
Additional information regardingthe requirementsset by EPAand
CARBis as follows:
It is important that you follow the maintenance specifications
provided in this manual to ensurethat your enginecomplies with
the applicableemission standardsfor the durationof the engine's
life. This engineis certified to operate on gasoline.The emission
control system on your generatorconsists of the following:
• FuelSystem • Air Induction System
FuelTank - Intakepipe/manifold
FuelCap _ Air cleaner
Carburetor • IgnitionSystem
FuelLines - Spark plug
• EvaporativeControl System _ Ignitionmodule
CarbonCanister • ExhaustSystem
Vapor Hoses _ PulseAir InjectionValve
Muffler
The Emissions Compliance Period referred to on the Emissions
Compliance Label indicatesthe number of operating hours for
which the enginehas beenshown to meet Federaland California
emission requirements. See the table below to determine the
compliance period for your generator.The displacementof your
generatoris listed onthe EmissionsComplianceLabel.
UNiTIDENTIFICATION(Figure2)
1. CarryingHandle:Lift the generatorby this handleonly.
2. Spark PlugCover:Allows access to the enginespark plug.
3. Fuel System Primer: Used to prime the fuel system for
starting.
4. Fuel Cap PressureValve: Allows air to enter the fuel tank to
equalizepressure.
5. FuelTankCap:Accessto fuel tankfor filling.
6. Control Panel: location of generator controls and output
receptacles.
7. Air IntakeSlats: Allows for cooling airto enterthe housing.
8. Muffler: Lowers engine exhaust noise (includes the spark
arrestor).
9. Choke:Cold enginestarting aid
10. Left Side ServiceCover: Allows access to air filter, fuel filter
and oil fill.
11. VentHoses: Hosesallow venting of the carburetor.
12. FuelShutoff:Controls fuel supply to the carburetor.
13. Starter Rope:Pullropefor starting engine.
Figure 2- Unit Identification
1
\
8\
12
11
10
9