Installation Guide

ManualsBrandsGeorge Kovacs ManualsCeiling LightsOutline Nickel Modern/Contemporary LED Flush Mount Light

INSTALLATION INSTRUCTIONS

Item# P1202

READ AND SAVE THESE INSTRUCTIONS

W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

Fig. 1 Wall Sconce

Fig. 3

Fig. 4

Fig.5

Fig. 2 Ceiling Mount

ASSEMBLING THE FIXTURE (Fig.1 / Fig.2)

Shut off power at the fuse box or circuit breaker. If necessary, remove the

old fixture including the mounting hardware.

Carefully remove the fixture from the carton and check that all parts are

included as show in Figure 1.

Loosen screws (C) and separate mounting plate (A) from fixture (D).

Attach mounting plate (A) to the junction box with junction box screws (B)

(size: 8-32*1/2”L). The side of the mounting plate marked “GND” must be

face out.

CONNECTION THE WIRES (Fig. 3)

Connect the electrical wires as shown in Fig.3, making sure that all wire nuts

are secured. If your outlet has a ground wire (green or bare copper),

connect the fixture's ground Wire to it. Otherwise, connect the fixture's

ground wire directly to the circular strap using the green screw provided.

Tuck the wire connections neatly into the junction box.

FINISHING THE INSTALLATION (Fig.1 / Fig.2)

Align fixture (D) onto mounting plate (A), and secure with screws (C).

(Please follow the arrow located inside the fixture back

plate marked “This side up” when the fixture assembly as

wall mount function as fig1)

To prevent moisture from entering the outlet box and causing a short circuit,

use clear caulking (i.e. Indoor/Outdoor silicone sealant) to outline the

outside of fixture back plate where it meets the wall leaving a space at

bottom to allow moisture a means to escape (Fig.4).

Your installation is now complete. Return power to the junction box and test the

fixture.

CAUTION /ATTENTION:

When handling the fixture, do not apply pressure to

the LED. Hold the fixture by the base or back plate only.

Replacing LED module (Fig. 5)

The LED module can be replaced by a qualified electrician without cutting of wire

and without damage to any decorative element to which the fixture is attached.

See installation steps for more details (Fig. 5)

Warning: Turn off power at the circuit breaker before replacing

LED module

a. To remove the fixture from the wall, loosen screws (C), remove the wire

connectors and place the fixture on a clear flat surface.

b. Loosen hex nuts (E) to separate fixture (N) from back plate (F).

c. Loosen screws (L), and remove rubber washers (M). Separate glass panel

(K) from LED housing (H).

d. Loosen screws (I) and hex nuts (G). Carefully remove the LED module (J)

from LED housing (H).

e. Reverse steps a-d for installing the new LED module.

Note: The LED module should be provided by a specified supplier.

FIXTURE

WIRES

Black or

Smooth

HOUSE

WIRES

Black

(Hot)

FIXTURE

WIRES

White or

Ribbed

HOUSE

WIRES

White

(Neutral)

FIXTURE

WIRES

Green or

Bare

Copper

(Ground)

HOUSE

WIRES

Green

(Ground)

Set

021

117110

- Mounting Plate

- Ground Screw

Mounting Screw*2

IMPORTANT:

Fixture should be installed by a qualified electrician to ensure

proper wiring and installation.

Dimmable with C-L (CFL & LED) type and Incandescent/Halogen type dimmers

Set

021

117110

- Mounting Plate

- Ground Screw

Mounting Screw*2