- Gianni Industries, Inc Door User Manual

P-MU-DG30 Ver. A Publish:2004.08.26 Page: 1/ 4

DG-30 Digital Keypad / Proximity Entry system

Operation User's Manual

1. Product Characteristic:

 Allows up to 150 Proximity cards / tokens or PIN codes

 Tamper Switch Included

 Door Reed Switch Input for Anti-Trailing

 Fully Programmable via keypad and master code

 Extendable from keypad only to proximity controller

 Supports 26 or 34-bit Wiegand auxiliary reader

 Logical memory to prevent duplication

 Non-Volatile Memory

 Invalid PIN Lock-out

2. Specifications:

 Operating Voltage: 12 Vdc

 Current Draw: 60mA Max @12VDC

 Input: request-to-exit, time out reed switch contact, auxiliary reader

 Relays Electric Current: 2A MAX @30Vdc ；0.4A @ 120Vac

 Memory Volume: 150 PIN codes or 100 Proximity cards/tokens and 50 PIN codes

 Format: 26 or 34-bit Wiegand hexadecimal.

 Relay 1 is controlled by 001~100 user slots（Cards or PIN codes）

 Relay 2 is controlled by 101~150 user slots（PIN codes）

 PIN codes: 5 digit codes only

 Case Material: ABS （UL94V0）

 Operating Temperature: -20~+70℃

 Ambient Humidity: 5~95% relative humidity non-condensing

 Visual Signals:

 Red: Power on

 Green: Relay activated

 Tri-color LED:

 Yellow: Program Mode

 Red: The slot is registered、Lock-out

 Green: This slot may register the card or PIN codes.

 Factory Master Code: 12345

 Invalid PIN Lock-out: The system will shut down for 60 seconds while 32 codes of

incorrectly Master Codes enrolled or PIN codes attempted.

 EPROM: Non-volatile memory, System will retain all programs and codes after a total

loss of power.

 Output: Dual relay, N.O./N.C./Com. Output (free voltage contact) 、Tamper switch

 Relay Activation Time: （＊10、＊20）

 Strike Time: 1~99 seconds（adjustable）

 Strike mode: Access Timer or Latch

 Color: Dark gray/ Beige White

PAGE 1
DG-30 Digital Keypad / Proximity Entry system Operation User's Manual 1. Product Characteristic: Allows up to 150 Proximity cards / tokens or PIN codes Tamper Switch Included Door Reed Switch Input for Anti-Trailing Fully Programmable via keypad and master code Extendable from keypad only to proximity controller Supports 26 or 34-bit Wiegand auxiliary reader Logical memory to prevent duplication Non-Volatile Memory Invalid PIN Lock-out 2.
PAGE 2
3.
PAGE 3
Followed By 「03」：This will set the system to be used as : Slots 001~150 for PIN codes only Note: When system format has the change, there’s a possibility the card stored would be invalid. Please reset the system and input all cards /tokens. Add card and deletion Enter the Programming mode, Enter the slot position code 「001~100」 A. Green light comes on: This slot position is ready to register the card 1. Present card in front of the readerÆYellow LED blinks (beep) Æ enrolled completed Æ（repeat） 2.
PAGE 4
Reset to Factory Master Code reset to Factory 「12345」 Insert the jumper RES1Æ 1-2 positionÆ5 audible beepsÆReset successfulÆ Return Insert the jumper to 2-3 position Remove all stored information Insert the jumper RES1Æ 1-2 positionÆ5 audible beepsÆ Master Code reset to Factory 「12345」Æ after 5 secondsÆ5 audible beepsÆ Remove all stored information Æ Return Insert the jumper to 2-3 position.