Operation Manual
Lombok A130/AL130A/A230/AL230A / Großbritannien / A31008-M2412-L101-1-7619 / Lombok.fm / 11.08.2014
Version 4, 16.09.2005
12
Resetting the base via the menu
Handsets are still registered, the system PIN is not reset.
MENU ¤ u Settings ¤ OK ¤ u Base ¤ OK ¤ u Base Reset ¤ OK ¤ Reset?
¤ OK
Resetting the base using the key on the base
All handsets are de-registered and the system PIN is reset to the original code 0000.
Carry out the following steps: Remove the mains cable from the base. Hold down the
registration/paging key on the base (¢ page 1)(¢ page 2) and reconnect the
power cable to the base at the same time. Hold the key down for at least 5 seconds.
Operating the base station on the PABX/router
Operating on the router
When operating the Gigaset on an analogue port of a router you can reduce problems
with
echoes by activating the Echo mode (¢ page 16). If you have no problems with
echoes, this function should be deactivated.
Operating on the PABX
The following settings are only necessary when your PABX requires them; see the user
guide for your PABX.
When entering the digits, enter them slowly one after the other.
Changing the dialling mode
MENU ¤
P#Q5#1N
¤ The number for the set dialling mode flashes:
0 = touch tone dialling (DTMF); 1 = dial pulsing (DP) ¤ enter number ¤ OK.
Setting recall
MENU ¤
P#Q5#1Q
¤ The number for the current recall flashes:
0
= 80 ms; 1 = 100 ms; 2 = 120 ms; 3 = 400 ms; 4 = 250 ms; 5 = 300 ms; 6 = 600 ms;
7
= 800 ms ¤ enter number ¤ OK.
Changing pause after line seizure
You can set the length of the pause inserted between pressing the talk key and
sending the phone number.
MENU ¤
P#Q5#1L
¤ The number for the current pause length flashes:
1 = 1 sec.; 2 = 3 sec.; 3 = 7
sec. ¤ enter number ¤ OK.
Changing the pause after the recall key
MENU ¤
P#Q5#12
¤ The number for the current pause length flashes:
1 = 800 ms; 2 = 1600 ms; 3
= 3200 ms ¤ enter number ¤ OK.
b
Appendix
Entering letters/characters
Specifications
Batteries
Technology: Nickel-metal-hydride (NiMH); Size: AAA (Micro, HR03); Voltage: 1.2 V;
Capacity: 400 - 1000 mAh
General specifications
Standard
characters
Press the relevant key
the number of times
indicated.
Briefly press the hash
key
# to switch from
"Abc" to "123" mode,
from "123" to "abc"
mode and from "abc"
to "Abc" mode.
1) Space
1x 2x 3x 4x 5x 6x 7x 8x 9x 10x 11x 12x 13x 14x 15x
1
1£$¥¤
2
abc2äáàâãç
I
def 3ëéèê
4
gh i4ïíìî
5
jkl5
L
mno6öñóòôõ
M
pqr s7ß
N
tuv8üúùû
O
wxy z9 ÿ ýæøå
Q
.,?!0+-:¿¡"’ ;_
P
*/()<=>%
#
#@\ &§
1)
DECT standard is supported
GAP standard is supported
Range up to 300 m outdoors, up to 50 m indoors
Base station power supply 230 V ~/50 Hz
Environmental conditions
in
operation
+5 °C to +45 °C, 20% to 75% relative humidity
Base station power consumption A130/A230 AL130A/AL230A
In standby mode
– Handset in base station
– Handset outside base station
ca. 1.0 W ca. 1.2 W
ca. 0.8 W ca. 1.0 W
During a call ca. 1.0 W ca. 1.2 W