INSTRUCTION MANUAL Deluxe Laser Line Generator Electronic alignment made easy • Melbourne • Perth • Auckland • Hong Kong • Shanghai • Taipei • New York • Verona • London • Paris LSLINE 040504 ed09 JJ
Contents Warranty 2 Introduction 3 Environmental protection 3 Scope of product 3 Description of symbols 3 Safety rules for laser line generator 4 Additional safety rules for laser line generator 4 Know your product 6 Changing the laser line generator batteries 7 Operating the laser line generator 7 Selecting the mounting method 7 Projection of a vertical laser line on the floor 8 Projection of laser line when fixed on a wall 8 Maintenance 9 Troubleshooting 9 Full 2 Years Home U
Description of symbols Dear Customer The rating plate on your tool may show symbols. These represent important information about the product or instructions on its use. If you require any help with your product, whether it is a Warranty claim, spare part or user information, please phone our Help Line for an immediate response. Phone 1300 880 001 in Australia or 0800 445 721 in New Zealand. Conforms to relevant standards for electromagnetic compatibility. Introduction Do not stare into beam.
Safety rules for laser line generators Additional safety rules for laser line generator The laser line generator is Class 2 with maximum 1mW and 400nm – 650nm wavelengths. These lasers do not normally present an optical hazard, although staring at the beam may cause flash blindness. WARNING. Do not stare directly at the laser beam.
atmospheres, such as in the presence of flammable liquids, gases, or dust. • Do not push the pin push-button of the aluminium base unless you intend to fix the base on the dry wall or soft wood like material, it may result injury because of the sharp pins. • To avoid injury, always make sure the push pins are fully retracted before handling or storing the laser line generator and keep the units and the base out of reach of children and other untrained persons. • Position the laser line generator securely.
Know your product Before using the laser line generator, familiarise yourself with all the operating features and safety requirements. Laser line generator 1. Laser switch 2. Laser line rotating dial 3. Level vials 4. Battery cover 5. Magnetic base 6. Front locating groove 7. Rear locating groove Leveling base 8. Vertical adjustment knob 9. Horizontal adjustment knobs 10. Locating pin 11. Mounting thread 15 Pin mounting base 12. Locating pin 13. Pin push buttons 14. Pin protective cover 15.
Changing the laser line generator batteries 3. If the floor is level, ensure the surface is made of soft material such as soft wood, then press both pin buttons (13) down into the flat surface and make sure it fixes firmly. Option 2: Flat surfaces – no mounting base 1. Place the unit on the floor and check the vials (3) to ensure that the surface is level. If the floor is not level, go to option 3. 1.
Projection of laser lines on the floor Projection of inclined laser line on the opposite surfaces Switch ON the laser line generator and adjust the rotating dial (2) to the required inclined angle on the opposite surface. NOTE. Position the laser line generator a maximum of 10m from the wall surface. It is recommended to use red laser enhancing glasses (15) to improve the visibility of the laser line especially in a bright light environment.
Maintenance 5. Switch ON the laser line generator. 6. Adjust the rotating dial (2) to achieve desired line projection. 1. The laser line generator must be handled with care. 2. Avoid shock, vibrations and extreme heat. 3. Always store the tool indoor, switch to OFF position and put it in its protective case. 4. Avoid dust and liquid into the tool, use damp cloth and mild soap to clean the tool. 5. Keep the laser line generator dry and clean. 6. Check the batteries regularly to avoid deterioration. 7.
Carefully read the entire Instruction Manual before using this product. Before returning this product for a Warranty Claim or any other reason Please Call 1300 880 001 (Australia) or 0800 445 721 (New Zealand) When you make your call, please have the following information at hand: With continuing product development changes may have occurred which render the product received slightly different to that shown in this instruction manual.