Installation Manual

2
BASIC OPERATION
Button (Local Control)
The button on the PS15Z-2 allows the user to turn the load attached to the controlled
outlet ON or OFF.
• Tapping button toggles the load attached ON or OFF.
• Include or exclude the module from the Z-Wave system.
When a Controller prompts to “Send Node ID” or to “Press Button on Unit”, quickly tap
the button once to satisfy those instructions. (Tapping the button also toggles the load
attached ON or OFF.)
Remote Control
The PS15Z-2 will respond to BASIC and BINARY commands that are part of the Z-Wave
system. Refer to your Controller’s instructions as to whether your Controller can transmit
those commands.
ADVANCED OPERATION
Protection
The PS15Z-2 supports the Protection Command. The module can be set to any one
of three Protection modes by a Z-Wave Controller. Refer to your Controller for information
on how to set the various modes of Protection. Some Controllers may only be able to set
certain settings of Protection. Regardless of the Protection setting, the module will operate
normally when using the Controller.
• When Protection is set to No Protection, the unit works normally, the
module will turn on and off with the button on the unit.
• When Protection is set to Child Protection, press the button on the module
three times rapidly to control the attached load.
• When Protection is set to Button Disabled, the button will not work to
turn the attached load on or off. The button can still be used to access the
Z-Wave network.
All On/All Off
The PS15Z-2 supports the ALL ON / ALL OFF commands. The module can be set to
respond to ALL ON and ALL OFF commands four different ways. Refer to your Controller
for information on how to set the module to operate in the manner you desire. Some
Controllers may be only able to set certain settings of ALL ON / ALL OFF response.
The four different ways the module can be setup are:
• Module responds to ALL ON and the ALL OFF command.
• Module responds to ALL OFF command but will not to ALL ON command.
• Module responds to ALL ON command but will not to ALL OFF command.
• Module does not respond to ALL ON or ALL OFF command.
Manufacturer Specifi c
The PS15Z-2 supports the Manufacturer Specifi c command. The module can return
Manufacturer Specifi c information about itself to the Controller. Refer to your Controller’s
instructions on how to get this information from the module.
CONFIGURATION
The PS15Z-2 supports the Confi guration command. The module can be confi gured
to operate slightly differently that it works when you fi rst install it. Using the confi guration
command you can confi gure the following (if your controller supports it) Set Parameter
104 to 1 for normal ON/OFF operation. Set Parameter 104 to 0 to enable fl ash mode
which operates as follows:
• With Parameter 104 value set to 0, relay is closed and module defaults to
ON (relay closed).
• Whenever the module receives a Z-Wave ON command, the module will
begin cycling its output relay on and off approximately once per second (1/2
second Off, 1/2 second On) for 20 seconds.
• If at any time during that 20 seconds, the module receives a Z-Wave OFF
command, the module will stop cycling its output relay and default to ON.
• At any time during that 20 seconds, if the module receives a Z-Wave ON
command, the module will add an additional 20 seconds on/off cycling of
its output relay. At the end of the 20 seconds, the module will again default
to ON (relay closed).
• At any other time, if the module receives an OFF command, it will have no
effect and the module remains ON.
SPECIFICATIONS
Power: 120 VAC, 60 Hz
Signal (Frequency): 908.42 MHz
Maximum Load: Incandescent: 600W maximum, 120 VAC
Resistive: 15 amps (1800 watts) maximum, 120 VAC
Motor: 1/2 H.P. maximum, 120 VAC
Range: Up to 100 feet line of sight between the Controller and or
closest Z-Wave Receiver module.
Z-Wave
®
and Z-Wave Plus
®
are registered trademarks of Sigma Designs
and its subsidiaries in the United States and other countries.
REGULATORY INFORMATION
The PS15Z-2 is certifi ed to comply with applicable FCC and IC rules and regulations governing RF and EMI emissions.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) This device must accept any interference received, including interference
that may cause undesired operation.
FCC Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician to help.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment
IC Notice
This Class B digital apparatus complies with Canadian ICES-003
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Le présent appareil est conforme
aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
This device complies with the Industry Canada license exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
WARRANTY
What is Covered?
Nortek Security & Control (“NS&C”) warrants to consumers who purchase this product for personal, family or
household purposes new from NS&C directly or from an authorized NS&C dealer, that the product will be free from
defects in materials and workmanship for a period of (1) year from the date of purchase. This warranty only applies if
the product is installed at a residence in the 50 United States or District of Columbia, and only at the site of the original
installation. It is not transferable. This warranty is not extended to resellers.
If a defect exists, NS&C will have you ship the defective part or product to us and we will, at our option, either repair
or replace it.
This warranty does not cover defects or damages caused by improper handling, maintenance, storage, installation,
removal or re-installation, misuse, non-factory authorized modifi cation or alteration, use of incompatible accessories,
electrical power problems or surges, impact by foreign objects, accident, fi re, acts of God, normal wear and tear
or shipping damage other than a shipment from NS&C. Note that all NS&C products are designed to be installed,
removed and serviced by trained individuals or professionals.
Keep your original sales receipt as it will be required to obtain warranty service.
This warranty shall not be extended or restarted upon receipt of any repaired or replacement part or product under this
warranty. No person is authorized to extend or otherwise modify this warranty.
How do I Obtain Warranty Service?
To obtain warranty service, email our Returns Department at [e-mail]. Include your name, address,
telephone number, the model number of your product, a copy of your original sales receipt, and a description of the
problem. Unless we need to discuss the situation further with you, you will be emailed a Return Authorization Number
and shipping instructions. If we need to discuss the situation further with you, we will call or email you. NS&C may
require troubleshooting on installed product before a Return Authorization Number is issued. Anything shipped to us
without a Return Authorization Number will be automatically returned unopened. You are responsible for the charges
for shipment to us, unless you are a California resident.
Limitations
THE DURATION OF ANY IMPLIED WARRANTY, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXCEED THE
WARRANTY PERIOD PROVIDED HEREIN.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply
to you.
NS&C SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING FROM THE BREACH OF ANY WRITTEN OR IMPLIED WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply
to you.
This warranty gives you specifi c legal rights, and you may also have other legal rights which vary from State to State.
IMPORTANT !!!
Radio controls provide a reliable communications link and fi ll an important need in portable wireless signaling.
However, there are some limitations which must be observed.
• For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices.
As such, they have limited transmitter power and therefore limited range.
• A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that
occur on or near their operating frequencies, regardless of code settings.
• Changes or modifications to the device may void FCC compliance.
• Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
• A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer,
and these facts should be communicated to the ultimate users.
Copyright © 2015 Nortek Security & Control LLC 10008859 X3
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,PS15Z-2,GO CONTROL; P/N: 10008859 X3; INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: 8.500” x 11.000”; TOLERANCE ± .125”; SCALE: 1-1; PAGE 2 OF 2