TTL 无线引闪器 TTL Wireless Flash Trigger 深圳市神牛摄影器材有限公司 GODOX Photo Equipment Co., Ltd. 地址/Add: 深圳市宝安区福海街道塘尾社区耀川工业区厂房2栋1层至4层、4栋1层至4层 1st to 4th Floor, Building 2/ 1st to 4th Floor, Building 4, Yaochuan Industrial Zone, Tangwei Community, Fuhai Street, Bao’an District, Shenzhen 518103, China 电话/Tel: +86-755-29609320(8062) 传真/Fax: +86-755-25723423 邮箱/E-mail: godox@godox.com www.godox.
Contents Foreword 24 Foreword Sync Socket Settings 25 Warning SHOOT Function Settings 26 Names of Parts C.Fn: Setting Custom Functions Body 37 Using the Flash Trigger LCD Panel As a Wireless Camera Flash Trigger 28 Battery Installing Batteries As a Wireless Outdoor Flash Trigger Battery Level Indication 29 Setting the Flash Trigger Power Switch Automatically Enter Power Saving Mode Wireless ID Settings Mode Settings Output Value Settings with X system e.g.
Warning Names of Parts Do not disassemble. Should repairs become necessary, this product must be sent to an authorized maintenance center. Always keep this product dry. Do not use in rain or in damp conditions. Keep out of reach of children. Do not use the flash unit in the presence of flammable gas. In certain circumstance, please pay attention to the relevant warnings. Do not leave or store the product if the ambient temperature reads over 50℃.
Battery Names of Parts LCD Panel 8 7 9 A M 1/128 B C 4 1 CH 01 2 5 3 10 11 V0.2 SYNC BLUE.T. BEEP ZOOM 1/4 AA alkaline batteries are recommended. Installing Batteries As shown in the illustration, slide the battery compartment lid of the flash trigger and insert two AA batteries separately. Battery Indication Check the battery level indication on the LCD panel to see the remaining battery level during the usage. Battery Level Indication Meaning 4 6 Group Display Menu 1. Channel (32) 2.
Setting the Flash Trigger Setting the Flash Trigger Power Switch Wireless ID Settings Slide the Power Switch to ON, and the device is on and status indicator lamp will not reveal. Note: In order to avoid power consumption, turn off the transmitter when not in use. Change the wireless channels and wireless ID to avoid interference for it can only be triggered after the wireless IDs and channels of the master unit and the slave unit are set to the same.
Setting the Flash Trigger Setting the Flash Trigger Output Value Settings Multi Flash Settings (Output Value, Times and Frequency) In the M mode 1. In the multi flash (TTL and M icon are not 1. Press the group button to choose the group, turn the select dial, and the power output value will change from Min to 1/1 in 0.3 stop increments. Press the button to confirm the setting. displayed). 2. The three lines are separately displayed as power output value, Hz(flash frequency) and Times(flash 2.
Setting the Flash Trigger Setting the Flash Trigger Modeling Lamp Settings Buzz Settings 1. Long press the
Setting the Flash Trigger Setting the Flash Trigger SHOOT Function Settings C.Fn: Setting Custom Functions Press the
button to enter C.Fn SHOOT. Press the button to choose one-shoot or multishoots, and press the button again to back to the main menu. One-shoot: When shooting, choose one-shoot. In the M and Multi mode, the master unit only sends DELAY SHOOT DIST STEP V0.2 APP 3/4 The following table lists the available and unavailable custom functions of this flash.Setting the Flash Trigger Custom Function Function Power output STEP value Setting Signs 1/128(0.3) 1/256(0.3) 1/128(0.1) 1/256(0.1) 3.0(0.1) 2.0(0.1) 5 (A-E) 3 (A-C) 60sec 30min 60min OFF 12sec OFF ON -3-+3 GROUP Group STBY Sleep LIGHT Backlighting time LCD Contrast ratio of LCD panel Appropriate MILC/DSLR camera models AF OPT Using the Flash Trigger Settings and Description The minimum output is 1/128(change in 0.3 step) The minimum output is 1/256(change in 0.
Using the Flash Trigger button to set the same channel to the flash trigger, and short press the < GR/CH> button to set the same group to the flash trigger (Note: please refer to the relevant instruction manual when setting the oudoor flashes of other models). 2.4 Press the camera shutter to trigger and the status lamp of the flash trigger turns red synchronously. 3. As a Wireless Original Flash Trigger Take HVL-F45RM as an example: 3.
Using the Flash Trigger 5. As a Wireless Shutter Release Trigger Operation method: 5.1 Turn off the camera. Take a camera remote cable and insert one end into the camera’s shutter socket and the other end to the shutter release port of X1R-S to connect. Power on the camera and the receiver. 5.2 Short press the
button to set channel, group, mode and parameters (refers to the contents of “Setting the Flash Trigger”). 5.Using the Flash Trigger 7.5 Full match and back to APP main interface. 7.6 When started the Bluetooth function, the Bluetooth icon will be displayed on the Compatible Smartphone Models This flash trigger can be used on the following Smartphone models: iPhone 6S iPhone 8 transmitter’s panel. 7.7 Set the channels of the slave flash and the transmitter to the same, and parameters e.g.
Compatible Flash Models Compatible Flash Models Compatible Flash Models The relationship of XT wireless system and X2 wireless system: Transmitter Receiver Flash X2T-S -- Note AD600 series/AD400 series/AD360II series XT-16 (Code Switch) ON ON ON ON ON ON ON ON CH01 CH02 CH03 CH04 CH05 CH06 CH07 CH08 ON ON ON ON ON ON ON ON CH09 CH10 CH12 CH13 CH14 CH15 CH16 AD200 series/V860II series/V850II X2 (Display Screen) V350S/TT685 series/TT600/TT350S QuickerII series/QTII/SK
Technical Data Technical Data Model X2T-S Model Compatible cameras Sony cameras (TTL autoflash) Wireless Flash Support for the cameras that have PC sync socket. Compatible smartphone iphone, Huawei, Samsung(see the compatible smartphone models for details) (sync flash in M mode) Power supply 2*AA batteries Flash Exposure Control X2T-S Transmission range (approx.) 0-100m Built-in wireless 2.
4. Whether the flash trigger and the receiver end equipment are in the low battery states or not Attentions 1. 2. 3. 4. Unable to trigger flash or camera shutter. Make sure batteries are installed correctly and Power Switch is turned on. Check if the transmitter and the receiver are set to the same channel, if the hotshoe mount or connection cable is well connected, or if the flash triggers are set to the correct mode. Camera shoots but does not focus.
FCC Statement A. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. B. Warning: Changes or modifications to this unit not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. C.