Installation Guide

ManualsBrandsGoldberg Brothers Inc. ManualsBuilding materials1-1/2 in. x 64 in. x 11-1/2 in. Steel Premium J-Strap Barn Door Hardware Set Moulding Rocket White

1

Attach the exposed

roller hangers to the

door

DOOR

TRACK

Door Edge

3”

1”

3 ½”

Aach the exposed

roller-hangers and

an-jump blocks to the

door as shown in the

diagram.

Aach T-guide to ﬂoor by aligning edge of guide with

edge of opening as shown above.

finished floor

T-guide flush to finished opening

WALL

DOOR

3/8”

1/4”

7/8”

FINISHED FLOOR

Plumb door before fastening door

guide to ﬂoor

3” from both sides of the top half of the door,

measure down 1⁄” and 5” and drill ⁄” pilot holes

followed by ⁄” pilot holes.

For large projects install templates are available

for purchase.

5”

1⁄”

3”

Oponal Accessories

Sidewall guide bracket

4 machine screws, 4 nuts, and 1

felt pad

Part #6001SW-*

NOTE: Use the

provided T-guide

screws for

Includes 1 bracket,

1 each

sidewall guide installaon.

Part #6001U-*

Door U-guide

NOTE: For U-guide installaon

use the T-guide screws provided

in the hardware set.

Includes 2 U-guides, 2 wood screws

and 1 felt pad

1 set

Track Connecng Plate

1 each

Part #6001C-*

Track Extension Kits

Includes 6 lag bolts and 6 spacers

1 set

So Stop

2 triggers, 4 wood screws

Part #6001SOFT17 (8’+ track)

Includes 2 So Stop mechanisms,

Part #6001SOFT11 (4’-7’ track)

* Indicates that the related part is available in various colors.

1 ⁄”

1 ⁄”

Li the door and

hang it from the track.

Using the

remaining hex lag

bolts, spacers, and

washers, ﬁnish

aaching the track

at the remaining

connecng points.

Using the same

method, aach

the opposite end

of the track to the

wall as shown.

Using a hex lag bolt, track

stop, spacer, and washer,

aach one end of the track

to the wall using the pre-

drilled hole closest to the

opening as shown in the

diagram.

NOTE:

The end of the track

should extend a minimum

of ⁄” past the door

opening as noted above.

⁄ʺ

Mark the centerline* of the

track on the wall using a level.

*The centerline of the track is

represented as the door

height (DH) + 1⁄ʺ above

ﬁnished ﬂoor.

At each of the track

connecng points, drill ⁄”

pilot holes, followed

by ⁄ʺ pilot holes.

DH + 1⁄” = track centerline

FINISHED FLOOR

Track Installaon

Goldberg Brothers, Inc.

10488 W Cen

tennial Rd, Suite 100

Lileton, CO 80127

(303) 321-1099

Track Centerline

1⁄ʺ door

1⁄ʺ door

2⁄ʺ door

⁄ʺ extension

Part #60013E-*

Part #60013EX-*

Part #60013EXX-*

⁄ʺ extension

Part #60014E-*

Part #60014EX-*

Part #60014EXX-*

1⁄ʺ extension

Part #60015E-*

Part #60015EX-*

Part #60015EXX-*

Swing the

track to the

opposite end

of the wall as

shown.

06/19/19