Installation Guide

Goldberg Brothers Barn Door Hardware sets come with a one-year manufacture’s
warranty for defective parts under normal installation and use. Warranty is subject to
repair or replacement of defective part/s at manufacture’s discretion and does not include
installation costs. Goldberg Brothers does not warrant the loss of finish at points where
roller is in contact with the track. Goldberg Brothers Barn Door Hardware is sold as a
rustic finished hardware and Goldberg does not warrant the imperfections seen through
the finish in steel parts. It is part of the look.
This document contains proprietary information of Goldberg Brothers, Inc. and its receipt
of possession does not convey any rights to reproduce or disclose its contents, or to
manufacture, use or sell anything it may describe. Reproduction, disclosure, or use
without prior written authorization from Goldberg Brothers, Inc. is strictly forbidden.
Included Hardware
Straight strap hangers (2) T-guide (1) Carriage bolts (4) Washers (6) An-jump blocks (2) Spacers (6)
Track stops (2) T-guide screws (2) Lock washers (4) Hex lag bolts (6) An-jump block screws (4) Hex nuts (4)
Using the carriage
bolts, hex nuts and
lock washers, aach
the horseshoe
hangers to the door
as shown in the
diagram.
Bumper:
Place 1 pad on stop
or edge of roller per side.
Stay:
Place 1 pad on top of track at
each end directly under roller
when roller is touching stop.
Bumper
Stay
DOOR
TRACK
Finished Opening
DOOR EDGE
½ʺ
ʺ
11
1
1ʺ
⁄ʺ
⁄ʺ
⁄ʺ
⁄ʺ
⁄ʺ
⁄ʺ
⁄ʺ
Using the T-guide screws, a ach the T-guide to the floor
by aligning the edge of the guide with the edge of
finished opening as shown above.
finished floor
WALL
DOOR
FINISHED FLOOR
Plumb the door before fastening door guide to floor.
Goldberg Brothers, Inc.
10488 W Cenntenial Rd, Suite 100
Lileton, CO 80127
[phone]
In the closed position, the
door should overlap the wall
a minimum of ⅜ʺ at the top
and a minimum of ½”on
both sides.
The edge of the door should
align with the end of the
track.
Note: After the door is hung
from the track, the anti-
jump blocks can be installed
directly behind the
horseshoe hangers.
At 3ʺand 9ʺ from both sides of the top half of the
door, measure down 1⁄ʺ and drill ⁄ʺ pilot holes
followed by ⁄ʺ holes. 6ʺ from both sides of the
top half of the door, measure down 4⁄ʺ and drill
⁄ʺ pilot holes followed by ⁄ʺ holes.
5ʺ
1⁄ʺ
3ʺ
Door Prep and Hanger Installaon
T-guide Installaon
Basic Installaon Layouts
GOLDBERG BROTHERS, INC.
Premium Series Horseshoe Hanger - Installation Instructions
Premium Hardware set
installed with no casing,
base, or other trim.
FINISHED OPENING
HEADER/BLOCK
WALL
DOOR
Premium hardware set installed on
track trim board that is equal to or
thicker than casing, base, or other trim.
FINISHED OPENING
HEADER/BLOCK
WALL
DOOR
Head Track Block
SIDE CASING
Base Board
Premium hardware set +
extension
kit installed where casing, base, or
other trim is greater than thick.
Extensions
FINISHED OPENING
HEADER/BLOCK
WALL
½ʺ Extensions
DOOR
Side Casing
Base Board
Premium hardware set + ½”
extension kit installed where casing,
base, or other trim is up to ½” thick.
⁄ʺ or 1⁄ʺ
1
3
3
⁄ʺ or 1⁄ʺ
⁄ʺ
⁄ʺ
⁄ʺ
⁄ʺ
FINISHED OPENING
HEADER/BLOCK
WALL
DOOR
SIDE CASING
BASE BOARD
STAY PAD
TRACK
BUMPER
DOOR
⁄ʺ
⁄ʺ
⁄ʺ
3ʺ
⁄ʺ
5⁄ʺ
3⁄ʺ
6ʺ
3ʺ
1⁄ʺ
⁄ʺ
Included Hardware
Horseshoe hangers (2) T-guide (1) Carriage bolts (6) Washers (6) An-jump blocks (2) Spacers (6)
Track stops (2) T-guide screws (2) Lock washers (6) Hex lag bolts (6) An-jump block screws (4) Hex nuts (6)
3ʺ
1⁄ʺ
6ʺ
4⁄ʺ
FINISHED OPENING
DOOR EDGE
2ʺ
Goldberg Brothers barn door track and hardware sets come with a one-year manufacturer’s
warranty for defective parts under normal installation and use. Warranty is subject to repair
or replacement of defective components at manufacturer’s discretion and does not include
installation costs.
Goldberg Brothers does not warrant the loss of finish at points where roller is in contact
with track. Goldberg Barn Track is sold as a rustic finished hardware and Goldberg does not
warrant the imperfections seen through the finish in the steel parts. It is part of the look.
With the exception of our stainless steel products, Goldberg Brothers does not warrant any
products installed and used outdoors or where they are exposed to weather, running water
or water condensation. Under these conditions, rust and other damage will naturally occur.
This warranty does not include loss or defects caused by elements outside the control of
Goldberg Brothers, Inc., such as natural disasters, weather, fire, water leakage, abuse,
improper installation, or anything else deemed out of the control of Goldberg Brothers, Inc.
Using the T-guide screws, aach the T-guide to the floor
by aligning the edge of the guide with the edge of
finished opening as shown above.
T-guide Installaon
Stay:
At each end of the track, place one felt pad strip on
top of the track, 1⁄ʺ in from the
track stop as shown.
Bumper:
For each hanger, place one felt
pad strip on the track stop or the
edge of the hanger as shown.
1⁄ʺ
An-jump block
6ʺ