Installation Guide

Assembly Instructions: 1083-3P
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture. For deep cleaning, turn off the light
and remove the glass prior to cleaning. Hand wash glass with warm water and mild detergent. Dry with a lint-free or microber cloth.
For Customer Service, please
contact the place of purchase.
PREPARING FOR INSTALLATION
Carefully remove the new xture from the carton as well as the yellow
bag that holds all of the parts. See the important notes above. Shut off
power at the circuit breaker and remove old xture from wall, including
the old mounting strap.
1. From the parts bag remove the mounting strap assembly. One
end of nipple (F) should be attached to mounting strap (A) with
washer (C) and hex nuts (D) in place. The other end should have
canopy loop (H) attached. Attach mounting strap (A) to the junction
box using mounting screws (B) and a screwdriver. Tighten securely.
Pull house wires through the center of the mounting strap. Unscrew
canopy loop collar (I) from canopy loop (H). Pass canopy (G) over
the mounted canopy loop to test the height. Approximately half
of the canopy loop’s exterior threads should be exposed, and the
canopyloopcollarshouldtsnuglyontothecanopyloop.Remove
canopy (G) and adjust the height of nipple (F) and canopy loop (H)
until the desired height is reached.
ASSEMBLING THE FIXTURE
2. Measure to determine the correct length of chain needed for
proper hanging height. If necessary, use a pair of pliers to open
and remove any excess chain. Attach one chain connector (K) to
each end of the chain (J). Attach top loop (L) to nipple (N) using
washer (M). Attach chain connector (K) and chain (J) to top loop (L).
Feedthexturewiresfromnipple(N)throughtoploop(L)through
the chain connector (K), and the chain (J) (every three links or so),
pulling the wires until taut. Use the remaining end of the chain
with chain connector (K) to attach the chain (J) to canopy loop
(H). Close the chain connectors to secure. Feed wires through the
canopy loop (H) and canopy (G). Slide canopy loop collar (I) and
canopy (G) down onto the chain/wires. Pull the wires until taut. Trim
the wires to the desired length plus 8 to 10 inches.
CONNECTING THE WIRES
3.Haveanassistantsupportthextureweightwhilecompletingthewiring.Attachthexture’swirestothehousewireswhichwere
pulled earlier from the junction box through the mounting strap (A). Connect black to black (transparent wire with black inner thread
or smooth); white to white (transparent wire with white inner thread or ribbed); ground to ground (green, transparent wire with green
inner thread, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the
same direction. If there is no ground wire (green or copper) coming from the junction box, locate ground screw (E) on the mounting
strapandwrapthexture’sgroundwirearoundthegreengroundscrew(E).Useascrewdrivertosecuregroundscrew(E)ontothe
mounting bracket. Tuck all wires neatly into the junction box.
FINISHING THE INSTALLATION
4. Hold canopy (G) up to the ceiling and slide canopy loop collar (I) up beneath the canopy (G). Tightly thread canopy loop collar (I)
onto canopy loop (H) to secure canopy (G) in place. Slide candle sleeves (P) over sockets. Adjust rope detail (O) after installation.
Installlightbulbs(notprovided)inaccordancewiththexture’sspecications.Donotexceedmaximumrecommendedwattage.
Yourinstallationiscomplete.Turnonthepowerandtestthexture.
House Wires
Fixture Wires
Hot
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
A
B
C
D
E
F
G
H
I
J
L
M
P
N
O
K