Installation Guide - CH

Assembly Instructions: 1157-SF
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important notes above. Shut off
the power at the circuit breaker and completely remove the old xture from the ceiling,
including the old mounting strap.
1. Take the mounting strap assembly from the parts bag. Mounting strap (A) contains several
threadedholes.Mountingscrews(B)shouldbexatedinplacewithhexnuts(C)securing
them to the mounting strap. If mounting screws (B) are not in place, hold the canopy up
to the mounting strap and insert mounting screws (B) through the mounting strap into the
exposedholesofthecanopyuntilthescrewthreadsprotrudefromtheholesinthecanopy.
Remove the canopy and then secure mounting screws (B) in place on the mounting strap
usinghexnuts(C).
2.Placethemountingstrap(A)overthejunctionboxandsecurethemountingstraptothe
junctionboxusingmountingscrews(D).Tightenthescrews(D)securelywithascrewdriver.
3. Pull house wires through the center of mounting strap (A).
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
For Customer Service, please
contact the place of purchase.
CONNECTING THE WIRES
4.Haveanassistantsupporttheweightofthexturewhilecompletingthewiring.Cut
awayanyexcesswireleaving8to10inchesofwireforinstallation.Attachthexture’s
wirestothehousewireswhichwerepulledearlierfromthejunctionboxthroughthe
mounting strap (A). Connect black to black (transparent wire with black inner thread or
smooth); white to white (transparent wire with white inner or ribbed); ground to ground
(transparent wire with green inner thread, green, or copper). Twist the ends of the wire
pairs together, and then twist on a wire connector. Make sure all twists are in the same
direction.Ifthereisnogroundwire(greenorcopper)comingfromthejunctionbox,locate
groundscrew(E)onthemountingstrapandwrapthexture’sgroundwirearoundthe
green ground screw (E). Use a screwdriver to secure ground screw (E) onto the mounting
bracket.Tuckallwiresneatlyintothejunctionbox.
FINISHING THE INSTALLATION
5.Holdthexturebodyuptothemountingstrap.Pushthecanopy(F)overthemounting
strap (A) until mounting screws (B) protrude from the holes in the canopy.
6.Threaddeconuts(G)ontotheexposedthreadsofmountingscrews(B).Tightendeco
nuts (G) so that the nuts are securing the canopy (F) to the mounting strap (A) and that
the canopy is snug against the ceiling.
7. Slip candle sleeve (H) over socket (I).
Installlightbulbs(notprovided)inaccordancewiththexture’sspecications.Donot
exceedthemaximumrecommendedwattage.
Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
House Wires
Fixture Wires
Hot
JUNCTION
BOX
A
B
C
E
D
F
G
H
I

Summary of content (1 pages)