Installation Guide
Assembly Instructions: 1323-3P WG (Ella)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important
notes above. Shut off the power at the circuit breaker and
completelyremovetheoldxturefromtheceiling,includingthe
oldmountingstrap.
Fromthepartsbagremovethemountingstrapassembly.Oneend
ofnipple(F)shouldbeattachedtomountingstrap(A)withhex
nuts(C,D)inplace.Theotherendshouldhavecanopyloop(H)
attached.
Mountingstrap(A)containsseveralpairsofthreadedholes.
Findthepairofholesthatmatchesthespacingoftheholeson
thejunctionbox.Attachmountingstrap(A)tothejunctionbox
usingmountingscrews(B)andascrewdriver.Tightensecurely.
Unscrew canopy loop collar (I) from canopy loop (H). Pass crystal
plate(U),metaldisc(T)andcanopy(G)overthemountedcanopy
looptotesttheheight.Approximatelyhalfofthecanopyloop’s
exteriorthreadsshouldbeexposed,andthecanopyloopcollar
shouldtsnuglyontothecanopyloop.Removecrystalplate(U),
metaldisc(T)andcanopy(G)andadjusttheheightofnipple(F)
andcanopyloop(H)untilthedesiredheightisreached.
ASSEMBLING THE FIXTURE
Rotatethearmsofthextureuntiltheyareinposition.Use
decorative nuts (P) and (U) to attach arms (O) to posts (N) and (T)
ofthexturebody.
Bymeasuring,determinethecorrectnumberofchainlinksneeded
forproperhangingheight.Ifnecessary,useapairofplierstoopen
andremoveanyexcesschain.Attachonechainconnector(K)to
each end of chain (J). Use one of chain connectors (K) to attach
chain (J) to top loop (L) and close the chain connector. Feed the
xturewiresupthroughthechain(everythreelinksorso),pulling
the wires until taut. Slide canopy loop collar (H) and canopy (G)
onto the chain/wire. Use the free chain connector (K) to attach
chain (J) to canopy loop (H).
CONNECTING THE WIRES
Haveanassistantsupportthextureweightwhilecompletingthe
wiring.Cutawayexcesswire.Threadthexturewiresthrough
canopyloop(H)andnipple(F).Attachthexture’swirestothe
powersupplywiresfromthejunctionbox.Connectblackto
black(orsmooth);whitetowhite(orribbed);groundtoground
(greenorcopper).Twisttheendsofthewirepairstogether,then
twist on a wire connector. Make sure all twists are in the same
direction.Ifthereisnogroundwire(greenorcopper)fromthe
junctionbox,locategroundscrew(E)onmountingstrap(A)and
wrapthexturegroundwirearoundthegreengroundscrew(E).
Useascrewdrivertosecuregroundscrew(E)ontothemounting
bracket.Tuckallwiresneatlyintothejunctionbox.
FINISHING THE INSTALLATION
Pushcrystalplate(U),metaldisc(T)andcanopy(G)uptothe
ceilingandslidecanopyloopcollar(I)upbeneaththecanopy.
Tightlythreadcanopyloopcollar(I)ontocanopyloop(H)tosecure
canopy (G) in place. Slide candle sleeves R) onto sockets (S).
Installbulbs(Q)(notincluded)inaccordancewiththexture’s
specications.Donotexceedthemaximumwattage.Refertothe
crystalinstallationsheettohangthecrystals.
Your installation is now complete. Turn on the power and test the
xture.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture. Dry with a lint-free or microber cloth.
For Customer Service, contact
the place of purchase to arrange
for replacement parts.
A
B
C
G
H
I
L
J
K
N
O
P
Q
R
S
M
F
E
D
T
U