Installation Sheet

Assembly Instructions: 3118-L (Hines)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important notes above. Shut off
the power at the circuit breaker and completely remove the old xture from the ceiling,
including the old mounting strap.
1. Take the mounting strap assembly from the parts bag. Mounting strap (B) contains several
threaded holes. Two of mounting screws (A) should be attached to mounting strap (B). You
may need to tighten nuts (C) that hold these screws in place. If the screws are not attached,
please hold canopy (G) up to mounting strap (B). Line up the holes in canopy (G) with the holes
in mounting strap (B) and insert mounting screws (A) into mounting strap (B) so that mounting
screws (A) protrude through the holes in canopy (G). Mounting screws (A) are long, please test
the canopy against the mounting strap to see how far you should insert the screws. Tighten
nuts (C) onto mounting screws (A) to hold the screws in place.
2. Pull the house wires through the center of mounting strap (B). Place mounting strap (B)
over the junction box so that mounting screws (A) are vertical, and in alignment with the hole
locationsonthexture’scanopy(G).
3. Secure mounting strap (B) to the junction box with mounting screws (D) and a screwdriver.
Tighten the screws securely.
ASSEMBLING THE FIXTURE
4.Rods(J)and(K)areonthexture’swires.Bymeasuring,determinethecorrectnumberof
rodsneededforproperhangingheight.*Thisxtureincludes(1)6”rod(J)and(3)12”rods(K).
Toshortenthexture,slidetheexcessrodsoffthewires.Additionalrodsmaybepurchased.To
lengthenthexture,addadditionalrodstothewires.
5.Pullthexture’swiresthroughrods(Jand/orK)untiltautandthreadtherodstogether.
Thread the bottom rod into post (M). Thread the top rod to the threads of the swivel joint on
canopy (G).
CONNECTING THE WIRES
6.Haveanassistantsupportthexture’sweightwhilecompletingthewiring.Refertothe
wiringdiagramandattachthexture’swirestothepowersupplywiresfromthejunctionbox.
Connect Hot to Hot, Neutral to Neutral, and Ground to Ground. Twist the ends of the wire pairs
together, and then twist on a wire connector. Make sure all twists are in the same direction. If
there is no house ground wire coming from the junction box, locate ground screw (E) on the
mountingbracket/mountingstrapandwrapthexture’sgroundwirearoundthegroundscrew.
Use a screwdriver to tighten the top of ground screw (E) onto the wires and into the mounting
bracket/mountingstrap.Tuckthewiresintothejunctionbox.
FINISHING THE INSTALLATION
7.Placethexture’scanopy(G)overmountingscrews(A)sothattheyprotrudethroughthe
holes in canopy (G). Thread deco nuts (H) onto mounting screws (A).
8. Slide shade (Q) over socket (N), place washer (L) over socket ring (P) and twist socket ring (P)
onto the threads of socket (N) to secure the glass in place.
Installalightbulb(notincluded)inaccordancewiththexture’sspecications.Donotexceed
the maximum recommended wattage.
Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
For Customer Service, please
contact the place of purchase.
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
House Wires
Fixture Wires
Hot
I
J
K
B
JUNCTION
BOX
D
A
E
C
F
H
G
L
N
M
Q
O
P