Installation Sheet
Assembly Instructions: 3602-2SF, 3SF (Duncan)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
1. PREPARING FOR INSTALLATION
Carefully remove all of the contents from the carton. See the
important notes above. Shut off the power at the circuit breaker
andcompletelyremovetheoldxturefromtheceiling,including
theoldmountingstrap.
Fromthepartsbagremovethemountingstrapassembly.
Mountingstrap(B)containsthreadedholes.Twoofmounting
screws(A)shouldbeattachedtomountingstrap(B).Youmay
needtotightennuts(C)thatholdthesescrewsinplace.Pull
thehousewiresthroughthecenterofmountingstrap(B).Place
mountingstrap(B)overthejunctionboxsothatmountingscrews
(A)arevertical,andinalignmentwiththeholelocationsonthe
xture’scanopy(F).Securemountingstrap(B)tothejunctionbox
withmountingscrews(D)andascrewdriver.Tightenthescrews
securely.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
For Customer Service, please
contact the place of purchase.
3. FINISHING THE INSTALLATION
Placecanopy(G)overmountingscrews(A)sothatthescrewsprotrudethroughtheholesinthecanopy.
Threaddeconuts(F)ontomountingscrews(A).
Twistthescrewsuntilthecanopyofthextureisattachedsnuglytotheceiling.
Slideshade(I)oversocket(H)andthreadsocketring(K)ontosocket(H)tosecuretheshadeinplace.
Installlightbulbs(notprovided)inaccordancewiththexture’sspecications.Donotexceedthemaximumwattage.
Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.
PleaseNote:Theswivelabovetheshadesallowstheshadestoberotated360degreesandusedasspotlights.
Smooth / Black /
Transparent (L)
Black (Hot)
Ribbed / White /
Transparent (N)
Bare Copper / Transparent with
Green Interior / Green
White (Neutral)
Green
(Ground)
B
JUNCTION
BOX
H
I
K
C
D
A
E
G
F
J
2. CONNECTING THE WIRES
Haveanassistantsupportthexture’sweightwhilecompletingthe
wiring.Cutawayexcesswire.Threadthexture’swiresthroughcanopy
loopandnipple.Attachthexture’swirestothepowersupplywiresfrom
thejunctionbox.Connectblacktosmooth/black/transparent(L)wire;
whitetoribbed/white/transparent(N)wire;groundtoground(greenor
copper).Twisttheendsofthewirepairstogether,andthentwistona
wire connector. Make sure all twists are in the same direction. If there is
nogroundwire(greenorcopper)fromthejunctionbox,locateground
screw(E)onmountingstrap(A)andwrapthexturegroundwirearound
thegreengroundscrew(E).Useascrewdrivertosecuregroundscrew
(E)ontothemountingbracket/mountingstrap.Tuckallwiresneatlyinto
thejunctionbox.