Installation Sheet

Assembly Instructions: 3602-L (Duncan)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
For Customer Service, contact
the place of purchase to arrange
for replacement parts.
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
House Wires
Fixture Wires
Hot
PREPARING FOR INSTALLATION
Carefully remove the new xture from the carton as well as
the yellow bag that holds all of the parts. See the important
notes above. Shut off power at the circuit breaker and
remove old xture including the old mounting strap.
1. From the parts bag remove the mounting strap
assembly. One end of nipple (F) should be attached
to mounting strap (A) with washer and hex nuts (C, D)
in place. The other end should have canopy loop (H)
attached.
2. Attach mounting strap (A) to the junction box using
mounting screws (B) and a screwdriver. Tighten securely.
Unscrew canopy loop collar (I) from canopy loop (H).
Pass canopy (G) over the mounted canopy loop to test
the height. Approximately half of the canopy loop’s
exterior threads should be exposed, and the canopy loop
collarshouldtsnuglyontothecanopyloop.Remove
canopy (G) and adjust the height of nipple (F) and canopy
loop (H) until the desired height is reached.
ASSEMBLING THE FIXTURE
3. Measure to determine the correct length of chain needed for proper hanging
height. If necessary, use a pair of pliers to open and remove any excess chain.
Attachoneofchainconnectors(K)tochain(J).Passthexturewiresthrough
toploop(L).Pullthewiresuntiltaut.Feedthexturewiresupthroughthechain
(every three links or so), canopy loop, canopy loop collar, canopy, and nipple
pulling the wires until taut. Use the free chain connector (K) to attach chain (J)
to canopy loop (H). Slide canopy loop collar (I) and canopy (G) down onto the
chain/wires. Pull the wires until taut. Trim the wires to the desired length plus 8
to 10 inches.
CONNECTING THE WIRES
4.Haveanassistantsupportthexture’sweightwhilecompletingthewiring.Refertothewiringdiagramandattachthexture’swires
to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire)
Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green
inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists
are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting
bracket/mountingstrapandwrapthexture’sgroundwirearoundthegroundscrew.Useascrewdrivertotightenthetopofground
screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
5. Push canopy (G) up to the ceiling and slide canopy loop collar (I) up beneath the canopy. Tightly thread canopy loop collar (I) onto
canopy loop (H) to secure canopy (G) in place.
6. Slide the shade (Q) over socket (M) and secure in place with socket washer (N) and socket ring (O).
7.Installlightbulb(notincluded)inaccordancewiththexture’sspecications.Donotexceedthemaximumrecommendedwattage.
8. Place diffuser (R) and cover (S) up beneath the bottom of shade (Q). Secure the diffuser and cover in place by tighten the provided
side screws.
Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.
Q
O
GND
B
D
G
I
J
K
A
E
C
F
H
L
M
N
R
S