Installation Guide

Assembly Instructions: 1567-5 (Riverton)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important notes
above. Shut off the power at the circuit breaker and completely remove
theoldxturefromtheceiling,includingtheoldmountingstrap.
Fromthepartsbagremovethemountingstrapassembly.Oneendof
nipple(F)shouldbeattachedtomountingstrap(A)withwasher(C)
andhexnut(D)inplace.Theotherendshouldhavecanopyloop(H)
attached.Attachmountingstrap(A)tothejunctionboxusingmounting
screws(B)andascrewdriver.Tightensecurely.Unscrewcanopyloop
collar (I) from canopy loop (H). Pass canopy (G) over the mounted
canopylooptotesttheheight.Approximatelyhalfofthecanopy
loop’sexteriorthreadsshouldbeexposed,andthecanopyloopcollar
shouldtsnuglyontothecanopyloop.Removecanopy(G)andadjust
theheightofnipple(F)andcanopyloop(H)untilthedesiredheightis
reached.
ASSEMBLING THE FIXTURE
Takethexture’sbodyoutofthebox.Arms(VandU)ofthextureare
closedinthepackaging.Feedthexture’swiresthroughtopofrod(O)
andpullthexture’swiresuntiltaut.Threadrod(O)topost(Q)until
tight.Threadnial(Z)ontonipple(Y).Feedthexture’swiresthrough
toploop(L)andtightentoploop(L)torod(O).Gentlyspreadthearms
untiltheyareevenlyspaced.Bymeasuring,determinethecorrect
numberofchainlinksneededforproperhangingheight.Ifnecessary,
useapairofplierstoopenandremoveanyexcesschain.Attachchain
connectors(K)toeachendofchain(J)beforeattachingoneendof
the chain connector/chain to top loop (L). Close the chain connector.
Connect the other chain connector (K) to canopy loop (H). Feed the
xture’swiresupthroughtoploop(L)thenthroughchain(J)(everythree
links or so). Pull the wires until taut. Slide canopy loop collar (I) and
canopy (G) onto the chain/wire.
CONNECTING THE WIRES
Haveanassistantsupportthexture’sweightwhilecompletingthe
wiring.Cutawayexcesswire.Threadthexture’swiresthroughcanopy
loopandnipple.Attachthexture’swirestothepowersupplywires
fromthejunctionbox.Connectblacktosmooth/black/transparent
(L)wire;whitetoribbed/white/transparent(N)wire;groundtoground
(greenorcopper).Twisttheendsofthewirepairstogether,andthen
twist on a wire connector. Make sure all twists are in the same direction.
Ifthereisnogroundwire(greenorcopper)fromthejunctionbox,locate
groundscrew(E)onmountingstrap(A)andwrapthexturegroundwire
aroundthegreengroundscrew(E).Useascrewdrivertosecureground
screw(E)ontothemountingbracket/mountingstrap.Tuckallwires.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
For Customer Service, contact
the place of purchase.
FINISHING THE INSTALLATION
Pushcanopy(G)uptotheceilingandslidecanopyloopcollar(I)upbeneaththecanopy.Tightlythreadcanopyloopcollar(I)onto
canopy loop (H) to secure canopy (G) in place. Slideglassshades(S)oversockets(T)andsecureinplacewithsocketrings(R).Install
lightbulbs(notprovided)inaccordancewiththexture’sspecications.Donotexceedthemaximumrecommendedwattage.
Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.
G
K
R
P
S
T
Y
Z
Q
U
L
O
M
N
X
V
J
D
C
A
I
B
E
H
F
JUNCTION
BOX