Instructions / Assembly

IMPORTANT:
• ALLINSTALLATIONWORKSHOULDBEDONEBYACCREDITEDPROFESSIONAL.
• SHUTOFFPOWERSUPPLYATFUSEORCIRCUITBREAKER!
• USEONLYTHESPECIFIEDBULBS.DONOTEXCEEDTHEMAXIMUMWATTAGE!
AssemblyInstructions:7011-M1L (Winslett)
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important notes above. Shut off the
power at the circuit breaker and completely remove the old xture from the ceiling, including
the old mounting strap.
1.Takethemountingstrapassemblyfromthepartsbag.Mountingstrap(B)containsseveral
threadedholes.Twoofmountingscrews(A)shouldbeattachedtomountingstrap(B).Youmay
needtotightennuts(C)thatholdthesescrewsinplace.Ifthescrewsarenotattached,pleasehold
canopy(F)uptomountingstrap(B).Lineuptheholesincanopy(F)withtheholesinmountingstrap
(B)andinsertmountingscrews(A)intomountingstrap(B)sothatmountingscrews(A)protrude
throughtheholesincanopy(F).Mountingscrews(A)arelong,sopleasetestthecanopyagainstthe
mountingstraptoseehowfaryoushouldinsertthescrews.Removethecanopyandthentighten
nuts(C)ontomountingscrews(A)toholdthescrewsinplace.
2.Placemountingstrap(B)overthejunctionboxandsecureinplacewithmountingscrews(D).
Tightenthescrewssecurelywithascrewdriver.
ASSEMBLING THE FIXTURE
3.Measuretodeterminethecorrectnumberofrods(Kand/orL)neededforproperhangingheight.
4.Threadthexture’swiresthroughrods(Kand/orL)beforethreadingtherodstogetherandthen
ontopost(M).Tolengthenthexture,addadditionalrods.Ifadditionalrodsareneeded,contact
theplaceofpurchasetoorder.Toshortenthexture,slideanyexcessrodsoffthexture’swires
todiscard.Pullthewiresthroughrodloop(I)andthreadrodloop(I)intothetoprod(KorL).Open
chainconnector(G)andhookthechainconnectortorodloop(I)andcanopyloop(P).Closechain
connector(G).Passthexture’swiresthroughthechainconnector,canopyloop,andcanopy(F).
Keepatleast8to10inchesofwiremorethanthedesiredlengthandtrimtheexcesswires.
For Customer Service, please
contact the place of purchase.
FINISHING THE INSTALLATION
6.Pushcanopy(F)uptotheceilingandtightlythreadnuts(H)ontothethreadsofmountingscrews(A).
7.Pushglassshade(O)upoverthethreadsofsocket(N).
8.Securetheglassinplacebytwistingsocketcover(J)ontothesocket.
9.Installalightbulb(notprovided)basedonthexture’sspecications.Donotexceedthemaximumwattage.
Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.
CONNECTING THE WIRES
5.Haveanassistantsupportthexture’sweightwhilecompletingthewiring.Refer
tothewiringdiagramandattachthexture’swirestothepowersupplywiresfrom
thejunctionbox.ConnectHottoHot(blackorsmooth),NeutraltoNeutral(white
orribbed),andGroundtoGround(greenorcopper).Twisttheendsofthewire
pairstogether,andthentwistonawireconnector.Makesurealltwistsareinthe
samedirection.Ifthereisnohousegroundwirecomingfromthejunctionbox,
locategroundscrew(E)onthemountingbracket/mountingstrapandwrapthe
xture’sgroundwirearoundthegroundscrew.Useascrewdrivertotightenthetop
ofgroundscrew(E)ontothewiresandintothemountingbracket/mountingstrap.
Tuckthewiresintothejunctionbox.
House Wires
Fixture Wires
Hot
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
A
B
C
D
E
F
G
P
H
I
J
K
L
M
N
JUNCTION
BOX
O