Installation Sheet

IMPORTANT:
• ALLINSTALLATIONWORKSHOULDBEDONEBYACCREDITEDPROFESSIONAL.
• SHUTOFFPOWERSUPPLYATFUSEORCIRCUITBREAKER!
• USEONLYTHESPECIFIEDBULBS.DONOTEXCEEDTHEMAXIMUMWATTAGE!
AssemblyInstructions:7011-SF (Winslett)
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture. Hand wash the glass with warm water and
mild detergent. Dry with a lint-free or microber cloth.
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important notes
above. Shut off the power at the circuit breaker and completely remove
the old xture from the ceiling, including the old mounting strap.
1.Takethemountingstrapassemblyfromthepartsbag.Mountingstrap(A)
containsseveralthreadedholes.Twoofthemountingscrews(C)shouldbe
attachedtomountingstrap(A).Placemountingstrap(A)overthejunctionbox
andsecureinplacewithmountingscrews(C).Tightenthescrewssecurely
withascrewdriver.Pullhousewiresthroughthecenterofmountingstrap(A).
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
House Wires
Fixture Wires
Hot
For Customer Service, please
contact the place of purchase.
FINISHING THE INSTALLATION
3.Holdcanopy(D)uptomountingstrap(A)andlineupthesideholesincanopy(D)withtheholesinmountingstrap(A)and
insertscrews(E)intotheexposedholesincanopy(D)andmountingstrap(A).Tightwithscrewdrivertosecurecanopy(D)tothe
mountingstrap(A)andthejunctionbox.
4.Liftglassshade(F)uptothesocketinthecenterofthecanopy(D).Securetheglassshade(F)tothexturebyscrewingon
socketcap(G)overthesocket.Theglassshadeshouldbesnugagainstthexturewiththeuseofthesocketcap(G),besurenot
toovertighten.
Please note overtightening the socket cap will cause the glass shade to crack.
Installalightbulb(notprovided)basedonthexture’sspecications.Donotexceedthemaximumwattage.
Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.
CONNECTING THE WIRES
2.Haveanassistantsupportthexture’sweightwhilecompletingthewiring.
Refertothewiringdiagramandattachthexture’swirestothepowersupply
wiresfromthejunctionbox.ConnectHottoHot(blackorsmooth),Neutralto
Neutral(whiteorribbed),andGroundtoGround(greenorcopper).Twistthe
endsofthewirepairstogether,andthentwistonawireconnector.Makesure
alltwistsareinthesamedirection.Ifthereisnohousegroundwirecoming
fromthejunctionbox,locategroundscrew(B)onthemountingbracket/
mountingstrapandwrapthexture’sgroundwirearoundthegroundscrew.
Useascrewdrivertotightenthetopofgroundscrew(B)ontothewiresand
intothemountingbracket/mountingstrap.Tuckthewiresintothejunctionbox.
A
B
C
D
E
F
G
JUNCTION
BOX