Instructions / Assembly

Assembly Instructions: 7312-BA1 (Bartlett)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important
notes above. Remove the old xture from the wall, including the
old mounting strap.
1. Take the mounting strap assembly from the parts bag. Mounting
strap (B) contains several threaded holes. Two of mounting screws
(A) should be attached to mounting strap (B). You may need to
tighten nuts (C) that hold these screws in place. If the screws are
not attached, please hold backplate (F) up to mounting strap (B).
Line up the holes in backplate (F) with the holes in mounting strap
(B) and insert mounting screws (A) into mounting strap (B) so
that mounting screws (A) protrude through the holes in the front
of backplate (F). Mounting screws (A) are long, please test the
backplate against the mounting strap to see how far you should
insert the screws. Tighten nuts (C) onto mounting screws (A) to
hold the screws in place.
2. Pull the house wires through the center of mounting strap (B).
Place mounting strap (B) over the junction box so that mounting
screws (A) are horizontal, and in alignment with the hole locations
onthexture’sbackplate(F).
3. Secure mounting strap (B) to the junction box with mounting
screws (D) and a screwdriver. Tighten the screws securely.
CONNECTING THE WIRES
4.Haveanassistantsupportthexture’sweightwhilecompleting
thewiring.Refertothewiringdiagramandattachthexture’s
wires to the power supply wires from the junction box. Connect
Hot to Hot, Neutral to Neutral, and Ground to Ground. Twist the
ends of the wire pairs together, and then twist on a wire connector.
Make sure all twists are in the same direction. If there is no house
ground wire coming from the junction box, locate ground screw
(E)onthemountingbracket/mountingstrapandwrapthexture’s
ground wire around the ground screw. Use a screwdriver to tighten
the top of ground screw (E) onto the wires and into the mounting
bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
5.Placethexture’sbackplate(F)overmountingscrews(A)so
that they protrude through the holes in the front of backplate (F).
6. Thread deco nuts (G) onto mounting screws (A). Twist until the
backplateofthextureissnugagainstthewall.
7. Push shade (I) over socket (H) and secure in place with socket
ring (M).
8.Installalightbulb(notincluded)inaccordancewiththexture’s
specications.Donotexceedthemaximumrecommended
wattage.
9. Place cage diffuser (L) into metal ring (J) and raise both up
under shade (I) and thread screws (K) into the holes in metal ring
(J) to hold it in place.
Your installation is now complete. Turn on the power and test the
xture.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
For Customer Service, please
contact the place of purchase.
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
House Wires
Fixture Wires
Hot
F
JUNCTION
BOX
EA
H
B
D
C
G
I
J
K
L
M