Installation Sheet

Assembly Instructions: 8401-3P (Leighton)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Removeallofthecontentsfromthecarton.Seetheimportantnotesabove.Removetheoldxturefromtheceiling,includingtheold
mounting strap.
1. Take the mounting strap assembly from the parts bag. One end of nipple (F) should be attached to mounting strap (A) with a washer
andhexnut(CandD)inplace.The other end should have canopy loop (I) attached.
2.Useascrewdriverandmountingscrews(B)toattachmountingstrap(A)tothejunctionbox.(Note:Whenmountingstrap(A)is
properlyinstalled,abouthalfoftheexteriorthreadsofnipple(F)areexposed,allowingcanopyloop(I)totsnuglyontonipple(F).You
maywanttotesttoensurethatwithcanopy(G)inplace,canopyloop(I)tsontonipple(F).Aftertesting,removeeverythingfromthe
nipple and place aside for later.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
For Customer Service, contact
the place of purchase.
FINISHING THE INSTALLATION
7. Push canopy (G) up to the ceiling and slide canopy loop collar (H) up beneath the canopy.
Tightly thread canopy loop collar (H) onto canopy loop (I) to secure canopy (G) in place.
8.Installlightbulbsinaccordancewiththexture’sspecications.Donotexceedthe
maximumwattage.
Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.
3. Laylantern(M)ontoitssideonaatsurfacewithlampbody(Q)closeby.Placespacers(R)overeach
bottom corner of lantern (M) and twist decorative screws (S) into the bottom corners of lantern (M).
4. Pull the wires through the rods until taut and thread the bottom of rod (P) onto post (U). Screw rod
connector (O) onto the top threads of rod (P). Thread rod (N) into rod (P). Position lamp body (U) inside
lantern(M).Pushthexture’swiresfollowedbypost(T)ofrod(N)throughtheholeatthetopoflantern(M).
5. Threadtoploop(L)ontopost(T).Bymeasuring,determinethecorrectnumberofchainlinks(J)needed
forproperhangingheight.Ifnecessary,useapairofplierstoopenandremoveanyexcesschain.Attach
oneofchainconnector(K)toeachendofchain(J).Useoneofchainconnectors(K)toattachchain(J)to
toploop(L)andclosethechainconnector.Feedthexture’swiresupthroughthechain(everythreelinks
orso),pullingthewiresuntiltaut.Slidecanopyloopcollar(H)andcanopy(G)ontothechainandwires.
Usethefreechainconnector(K)toattachchain(J)tocanopyloop(I).
CONNECTING THE WIRES
6.Haveanassistantsupportthexture’sweightwhilecompletingthewiring.Cutawaytheexcess
wires.Threadthexture’swiresthroughthecanopyloopandnipple.Refertothewiringdiagramand
attachthexture’swirestothepowersupplywiresfromthejunctionbox.ConnectHottoHot,Neutral
toNeutral,andGroundtoGround.Twisttheendsofthewirepairstogether,andthentwistonawire
connector. Make sure all twists are in the same direction. If there is no house ground wire coming
fromthejunctionbox,locategroundscrew(E)onthemountingbracket/mountingstrapandwrapthe
xture’sgroundwirearoundthegroundscrew.Useascrewdrivertotightenthetopofgroundscrew
(E)ontothewiresandintothemountingbracket/mountingstrap.Tuckthewiresintothejunctionbox.
House Wires
Fixture Wires
Hot
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
A
B
C
D
E
F
G
H
I
J
K
K
L
M
N
O
P
Q
R
S
T
U