Installation Sheet
IMPORTANT:
• ALLINSTALLATIONWORKSHOULDBEDONEBYACCREDITEDPROFESSIONAL.
• SHUTOFFPOWERSUPPLYATFUSEORCIRCUITBREAKER!
• USEONLYTHESPECIFIEDBULBS.DONOTEXCEEDTHEMAXIMUMWATTAGE!
AssemblyInstructions:9808-3/3SF & 5/5SF (Seaport)
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important notes above. Shut off
the power at the circuit breaker and completely remove the old xture from the ceiling,
including the old mounting strap.
Thisxturemaybemountedwithrodsasapendantorwithoutrodsasaclosetotheceilingor
semi-ushmount.
1.Takethemountingstrapassemblyfromthepartsbag.Mountingstrap(B)containsseveral
threadedholes.Twoofmountingscrews(A)shouldbeattachedtomountingstrap(B).You
mayneedtotightennuts(C)thatholdthesescrewsinplace.Ifthescrewsarenotattached,
pleaseholdcanopy(F)uptomountingstrap(B).Lineuptheholesincanopy(F)withtheholes
inmountingstrap(B)andinsertmountingscrews(A)intomountingstrap(B)sothatmounting
screws(A)protrudethroughtheholesincanopy(F).Mountingscrews(A)arelong,soplease
testthecanopyagainstthemountingstraptoseehowfaryoushouldinsertthescrews.
Tightennuts(C)ontomountingscrews(A)toholdthescrewsinplace.
2.Placemountingstrap(B)overthejunctionboxandsecureinplacewithmountingscrews
(D).Tightenthescrewssecurelywithascrewdriver.
ASSEMBLING THE FIXTURE
3.Rods(L)areonthexture’swires,butnotconnectedtothexture.Bymeasuring,
determinethecorrectnumberofrodsneededforproperhangingheight.It is possible to
install the xture without using any of rods (L), by connecting swivel post (I) directly
onto post (M). Please see the diagram for SEMI-FLUSH INSTALLATION.Ifinstallingasa
pendant,connectrods(L)togetherandthentothexturebodyatpost(M).Tolengthenthe
xture,addadditionalrods.Ifadditionalrodsareneeded,contacttheplaceofpurchaseto
order.Toshortenthexture,slideanyexcessrodsoffthexture’swirestodiscard.Trimthe
wiresafteraddingatleast8to10inchesofwiretothedesiredlength.Twisttoprod(L)onto
thethreadsofswivelpost(I)ofcanopy(F).Locktherodinplacebytwistingthescrewon
swivelpost(I).Pullthexture’swiresthroughthetopofcanopy(F).
CONNECTING THE WIRES
4.Haveanassistantsupportthexture’sweightwhilecompletingthewiring.Refertothe
wiringdiagramandattachthexture’swirestothepowersupplywiresfromthejunctionbox.
ConnectHottoHot,NeutraltoNeutral,andGroundtoGround.Twisttheendsofthewirepairs
together,andthentwistonawireconnector.Makesurealltwistsareinthesamedirection.If
thereisnohousegroundwirecomingfromthejunctionbox,locategroundscrew(E)onthe
mountingbracket/mountingstrapandwrapthexture’sgroundwirearoundthegroundscrew.
Useascrewdrivertotightenthetopofgroundscrew(E)ontothewiresandintothemounting
bracket/mountingstrap.Tuckthewiresintothejunctionbox.
PENDANT INSTALLATION
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
House Wires
Fixture Wires
Hot
For Customer Service, please
contact the place of purchase.
FINISHING THE INSTALLATION
5.Pushcanopy(F)uptotheceilingandtightlythreadnuts(H)ontotheexposedthreadsofmountingscrews(A).
6.Installlightbulbs(notprovided)basedonthexture’sspecications.Donotexceedthemaximumwattage.
7.Slidemetalcages(N)uptothebottomofcaps(P).Securethemetalcagesinplacewiththeremaining
decorativenuts(H).
Please note that you can move the light source at joint (O) to adjust the angle of the light source.
Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.
SEMI-FLUSH INSTALLATION
N
M
H
P
G
N
D
A
E
D
B
C
F
I
H
L
L
L
L
O
H
H
F
P
N
O