Installation Sheet

ManualsBrandsGolden Lighting ManualsChandeliersGolden Lighting Autumn 40" Wide Crystal Abstract Chandelier

Assembly Instructions: 9903-12 (Autumn Twilight)

IMPORTANT:

• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.

• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!

• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!

CLEANING TIPS

Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the

xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture. Dry with a lint-free or microber cloth.

For Customer Service, please

contact the place of purchase.

PREPARING FOR INSTALLATION

Carefully remove all of the contents from the carton.

See the important notes above. Shut off the power

at the circuit breaker and completely remove the old

xture from the ceiling, including the old mounting

strap.

1. From the parts bag remove the mounting strap assembly.

One end of threaded rod (F) should be attached to

mounting strap (A) with washer (C) and hex nut (D) in place.

2. Pull the house wires through the center of mounting strap

(A). Place mounting strap (A) over the junction box and

secure in place with mounting screws (B) and a screwdriver.

Tighten the screws securely.

ASSEMBLING THE FIXTURE

3. Measure to determine the correct length of cable wires

neededforproperhangingheight.Toshortenthexture,

trim the wires to the desired length plus at least 8 to 10

inches.Putthexture’swirethroughtheholeinthesideof

canopy (G).

FINISHING THE INSTALLATION

5. Push canopy (G) up to the ceiling so that threaded rod (F) protrudes through the hole in canopy (G). Secure canopy (G) to the ceiling by

threading decorative nut (H) onto threaded rod (F).

6.Installthecrystals.Toproperlyinstallcrystalsleaves(K),ipthepageandrefertotheattachedcrystaldiagram.

7.Installlightbulbs(notprovided)inaccordancewiththexture’sspecications.Donotexceedthemaximumrecommendedwattage.

Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.

CONNECTING THE WIRES

4.Attachthexture’swirestothepowersupplywiresfromthe

junction box. Connect black to black (or smooth); white to white (or

ribbed); ground to ground (green or copper). Twist the ends of the

wirepairstogether,thentwistonawireconnector.Makesureall

twists are in the same direction. If there is no ground wire (green or

copper)fromthejunctionbox,locategroundscrew(E)onmounting

strap(B)andwrapthexture’sgroundwirearoundthegreenground

screw (E). Use a screwdriver to secure ground screw (E) onto the

mounting bracket. Tuck all wires neatly into the junction box.

How to Identify the Fixture’s Wires

Hot Neutral Ground

Smooth

Ribbed

Bare Metal,

Green, or

Green Inner

Thread

Black

White

Black Inner

Thread

White Inner

Thread

House Wires

Fixture Wires

Hot

76PCS

Summary of content (2 pages)

PAGE 1
Assembly Instructions: 9903-12 (Autumn Twilight) IMPORTANT: • ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL. • SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER! • USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE! For Customer Service, please contact the place of purchase. PREPARING FOR INSTALLATION E F A B C D G Carefully remove all of the contents from the carton. See the important notes above.
PAGE 2
Assembly Instructions: 9903-12 (Autumn Twilight) - cont. CRYSTAL DIAGRAM Screw crystal leaves (K) onto the empty screw posts on the fixture body. Refer to the diagram below which demonstrates how to properly hold crystal leaves (K). Hold the crystals carefully by the metal base to prevent the crystals from cracking or breaking. The crystal beads are tied up in bags on the fixture body. Carefully tear open the bags and arrange the strings of beads.