Instructions / Assembly

ALL LOCKING MECHANISMS MUST BE ENGAGED BEFORE USING
THE LADDER.
DANGER
LADDER CONFIGURATIONS
KEEP ALL BODY PARTS CLEAR OF SLIDING STEPS AND RUNGS DURING ADJUSTMENT.
WARNING
NEVER USE THE LADDER IN 90 DEGREE IF LADDER IS NOT ON A FLAT LEVEL SURFACE.
WARNING
NOTE: MUST ONLY BE USED WHEN BACK OF LADDER IS AGAINST A
WALL AND THE LADDER IS ON A FLAT LEVEL SURFACE.
PROPER SET-UP AND HEIGHT ADJUSTMENTS
The ladder must only be used in this position when one side of the ladder is
one rung shorter than the other side. Only use ladder against a solid wall.
From the storage position (see Figure 19), unlock both adjustable hinges to
disengage the locks as indicated in Figure 1. Pull the two sections of the ladder
apart until both hinges snap into place and securely lock (see Figure 20).
To increase the height of the ladder, unlock the rail locks on one side of the
ladder and tip the ladder to its side to allow the outer section to drop to your
desired height (see Figure 21). When you are at your desired height, lock the
rail locks.
Unlock the rails locks on the first side of the ladder and tip the ladder to its
side to allow the outer section of the ladder to drop so the height is one rung
shorter than the first side. Lock rail locks.
Visually make sure the rail locks are in the locked position and no
red is showing.
The ladder is properly aligned when one side of the ladder is one rung shorter
than the other. (see Figure 22)
To return the ladder back to its lowest position, reverse the process above.
Figure 19 Figure 20
Figure 21 Figure 22
Figura 19 Figura 20 Figura 21 Figura 22
TODOS LOS MECANISMOS DE BLOQUEO TIENE QUE ESTAR FIJADOS
ANTES DE USAR LA ESCALERA.
PELIGRO
CONFIGURACIONES DE LA ESCALERA
AL AJUSTAR, MANTÉN TODAS LAS PARTES DEL ARMAZÓN LIBRES DE PELDAÑOS Y
ESCALONES DESLIZANTES.
ADVERTENCIA
NO USAR JAMÁS UNA ESCALERA EN LA POSICIÓN DE 90 GRADOS SI NO ESTÁ SOBRE
UNA SUPERFICIE PLANA NIVELADA.
ADVERTENCIA
NOTA: USAR SOLO CUANDO LA ESCALERA ESTÉ SOBRE UNA
SUPERFICIE PLANA NIVELADA Y SU PARTE POSTERIOR ESTÁ
APOYADA CONTRA UNA PARED.
90 GRADOS
INSTALACIÓN Y AJUSTES DE ALTURA ADECUADOS
La escalera tiene que usarse en esta posición sólo cuando un lado tiene un
escalón menos que el otro. Usa la escalera solo contra paredes sólidas.
Desde la posición de almacenaje (Ver Figura 19), desbloquea ambas bisagras
ajustables para liberar los bloqueos como se indica en la Figura 1. Separa las
dos secciones de la escalera tirando de ellas hasta que ambas bisagras
encajen en su lugar y queden bloqueadas con seguridad (Ver Figura 20).
Para incrementar la altura de la escalera, libera los bloqueos de riel a un lado
de la escalera e inclínala de lado para permitir que la sección exterior caiga a
la altura deseada (Ver Figura 21). Al alcanzar la altura deseada, fija los
bloqueos de riel.
Libera los bloqueos de riel del otro lado de la escalera e inclínala de lado para
permitir que la sección exterior caiga a la altura de un escalón menos con
respecto al otro lado. Fija los bloqueos de riel.
Fíjate bien que todos los bloqueos de riel están en la posición de bloqueo y
que ninguno se muestre rojo.
La escalera está bien alineada cuando uno de sus lados tiene un escalón
menos que el otro. (Ver Figura 22)
Para colocar la escalera en su posición anterior más baja, procede a la inversa
de como se indicó más arriba.
12
12
90 DEGREE