User manual

Edited in Germany • Subject to change without notice • A pdf version is available on the Internet
GMC-I Messtechnik GmbH
Südwestpark 15
90449 Nürnberg •
Germany
Phone [phone]
Fax [phone]
E-Mail [e-mail]
www.gossenmetrawatt.com
9 Order Information
* 115 V variant available with appendix -S001
Mounting
10 Repair and Replacement Parts Service,
Calibration Center* and Rental Service
If required please contact:
GMC-I Service GmbH
Service Center
Thomas-Mann-Str. 20
90471 Nürnberg
• Germany
Phone [phone]
Fax [phone]
E-Mail [e-mail]
www.gmci-service.com
This address is only valid in Germany. Please contact our
representatives or subsidiaries for service in other countries.
* DAkkS Calibration Laboratory for Electrical Quantities
D-K-15080-01-01 accredited per DIN EN ISO/IEC 17025
Accredited quantities: direct voltage, direct current value, direct current resistance,
alternating voltage, alternating current value, alternating current active power,
alternating current apparent power, DC power, capacitance, frequency and
temperature
Competent Partner
GMC-I Messtechnik GmbH
is certified in accordance with
DIN EN ISO 9001:2008.
Our DAkkS calibration laboratory is accredited by the Deutsche
Akkreditierungsstelle GmbH (National accreditation body for the
Federal Republic of Germany) in accordance with DIN EN ISO/IEC
17025 under registration number D-K-15080-01-01.
We offer a complete range of expertise in the field of metrology:
from test reports and factory calibration certificates, right on up to
DAkkS calibration certificates.
Our spectrum of offerings is rounded out with free test equipment
management.
Our service department includes an on-site DAkkS calibration bench.
If errors are discovered during calibration, our specialized
personnel are capable of completing repairs using original
replacement parts.
As a full service calibration lab, we can calibrate instruments from
other manufacturers as well.
11 Product Support
If required please contact:
GMC-I Messtechnik GmbH
Product Support Hotline
Phone [phone]
Fax [phone]
E-Mail [e-mail]
Description (abbreviated name) Type Article No.
SSP-KONSTANTER 120-20 32 N 20 RU 10 P K320A*
SSP-KONSTANTER 120-40 32 N 40 RU 6 P K321A*
SSP-KONSTANTER 120-80 32 N 80 RU 3 P K322A*
SSP-KONSTANTER 240-20 32 N 20 RU 20 P K330A*
SSP-KONSTANTER 240-40 32 N 40 RU 12 P K331A*
SSP-KONSTANTER 240-80 32 N 80 RU 6 P K332A*
SSP-KONSTANTER 320-32 32 N 32 RU 18 P K334A*
IEEE 488 interface for SSP KONSTANTER types 32 N ...
Weight: 172 g,
Dimensions: 150 x 100 x 60 (L x W x H)
K380A
Description Note Article No.
19" rack adapter, 1 x 32 N Required for mounting one type 32 N ...
device to a 19" rack
Weight: 214 g (packed in plastic bag)
K990A
19" rack adapter, 2 x 32 N Required for mounting two type 32 N ...
device to a 19" rack
Weight: 50 g (packed in plastic bag)
K990B
Mains jumper cable, 0.4 m The cable is equipped with a 10 A inlet
plug and a 10 A inlet socket.
It is used for looping mains power through
when several devices are mechanically
combined into a multi-channel unit. In this
way, the complete unit requires only one
mains power cable.
Weight: 102 g (packed in plastic bag)
K991A
RS 232 bus cable, 2 m For connecting a device to an RS 232
interface (extension cable with 9-pin
socket and 9-pin plug connector).
Weight: 232 g (packed in plastic bag)
GTZ3241000
R0001