Safety Instructions

ManualsBrandsGOTO ManualsBattery ChargersWireless Charging Stand 10W

Status LED

Start-up (Power On) Solid White 3 Seconds

Charging Solid White

Fully Charged Solid White

Insufﬁcient from Power Source Intermittent White Light

FOD (Foreign object detected) Solid Red

Temperature Fault Solid Red

Power Source Error Solid Red

Standby None/Off

• It’s recommended to use the provided wall adapter & Type C cable to

power your wireless charging stand.

• With the screen facing out, place your Qi-enabled smartphone vertically so

that it aligns with the center of the stand. Or, place it horizontally centered

on the front-side stand holder.

8820-01593 Rev. A00

Wireless Charging Stand 10W

SKU/MODEL: TM0022P

• LED light will indicate charging status as summarized in the table below.

• Do not place magnetic mounts, metal cases, keys, coins, or other objects between your

phone and the charger. It might reduce performance or damage magnetic strips or RFID

chips like those found in some credit cards, security badges, and passports. If your

case holds any of these sensitive items, remove them before charging or make sure they

aren’t between the back of your phone and the charger. The stand has sensors which

detects objects which are not supposed to be placed to prevent the charger emitting

unnecessary power and heat that could damage your smartphone and other heat-

sensitive items.

Safety Instructions:

1. Please read these instructions before using the device to ensure safe and proper use.

2. Connect the wall adapter of the wireless charging stand into a socket outlet that is close

by and is easy to disconnect from the source.

3. Use indoors and in a dry location only; keep away from wet or damp locations.

4. Keep wireless charging stand and wall adapter away from any liquids or moisture.

5. Unplug the wireless charging stand when unused for long periods of time.

6. Do not store your device in very hot or very cold areas. It is recommended to use your

device at room temperatures.

7. Caution: If you experience problems with the wireless charging stand, please discontinue

use, unplug the wall adapter of the wireless charging stand from the AC socket, and contact

T-Mobile for assistance.

8. Do not use if visible defects are observed on the wireless charging stand or wall

adapter. Do not attempt to service or disassemble.

FCC Statement

DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC

COMPATIBILITY

We, T-Mobile, of 12920 SE 38th St., Bellevue, WA 98006, Tel:+1(877)453 1304, declare

under our sole responsibility that the product, to which this declaration relates,

complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired

operation.

Federal Communications Commission Interference Statement

If device is placed

correctly in the middle

and charging, the light

will be solid white.

If device is not placed

correctly in the middle,

it will not charge and the

light will be off.

Do not place foreign

objects on the stand, the

light will be solid red for

certain objects.

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation.

This equipment generates, uses, and can radiate radio frequency energy, and if

not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try and correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the distance between the equipment and the receiver.

• Connect the equipment to an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modiﬁcations not expressly approved by the party

responsible for compliance could void the user’s authority to operate this equipment.

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. End users must follow the speciﬁc operating instructions

for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure

compliance requirements, please follow operation instructions as documented in this

manual. This equipment should be installed and operated with a minimum distance of

20 cm between the radiator and your body.

See T-Mobile’s Terms and Conditions (including arbitration provision) at T-Mobile.

com, for additional information, and restrictions and details. T-Mobile and the

magenta color are registered trademarks of Deutsche Telekom AG.

3 4

iPhone 13/12 mini

Business Unit:

Program Manager:

Packaging Engineer:

Material:

Blank Size (in):

Side Shown:

L x W x D (mm):

DIE LAYOUT

Unit:

Flute/Grain:

REV

Intermediate

PRINT SIDE

L x W x D (in):

[285.750]

[95.250]

[110.109]

FRON T

BACK

QIG/FCC Statement

70 gsm woodfree paper

IN/MM

Drawing Scale 1:1

Retail Outside Dimension (Including Hang Tab)

DO NOT PRINT

DIE LINES, PRINTERS NOTES

PRINT SPECS:

DIE/MATERIAL SPECS:

Die Line File:

Core

Matthew Duffy

Please refer to drawing

IDL_TM0007P_T-MOBILE 10W WIRELESS CHARGING PAD QIG-FCC

Color Plates:

Notes:

Artwork File:

vertical

RELEASE DATE:

08/02/2019

Tolerance:+/- 1/32" - 0.8mm

Blank Size (mm):

Finish:

DIELINE:

THIS DOCUMENT & THE INFORMATION

IN IT ARE THE CONFIDENTIAL PROPERTY

OF BELKIN INTERNATIONAL AND MUST

NOT BE COPIED, REPRODUCED OR USED

IN ANY MANNER WITHOUT THE WRITTEN

CONSENT OF BELKIN CORPORATION.

IT MUST BE RETURNED UPON REQUEST

This dieline works for following skus (if any):