Installation And Safety Instructions

ManualsBrandsGracie Oaks ManualsAll Ceiling Fans22" Grimsby 3 Blade Ceiling Fan with Remote, Light Kit Included

INSTALLATION AND SAFETY INSTRCUTIONS

SAFETY PRECAUTION

Transmitter Kit

Wall Screw x 2Transmitter HolderTransmitter Battery

Assembly Kit

Expansion Bolt x 4 Self Tapping Screw &Washer x 4

CR2032/3V

1hr 6hr3hr

• WARNING –To make sure power is off before attempting installation.

• WARNING – Support Directly From Building Structure.

• WARNING –To reduce the risk of fire, electric shock, or injury to persons, unplug or disconnect the

appliance from the power supply before the fan installation, cleaning, or servicing.

• WARNING –Suitable for use with solid-state speed controls.

• WARNING –To Reduce The Risk Of Personal Injury, Do Not Bend The Blade Brackets When Installing The

Brackets, Balancing The Blades, Or Cleaning The Fan. Do Not Insert Foreign Objects In Between Rotating Fan

Blades.

• The installation is to be in accordance with the National Electrical Code, ANSI/NFPA 70-1999 and local

codes. Consult a qualified electrician if in double.

• WARNING – To Reduce The Risk Of Electric Shock, This Fan Must Be Installed With A General-Use,

Isolating Wall Control/Switch.

• All set screws must be checked, and retightened where necessary, before installation.

• After making the wire connections, the wires should be spread apart with the grounded conductor and

the equipment-grounding conductor on one side of the outlet box and the ungrounded conductor on the

other side of the outlet box.

• The splices after being made should be turned upward and pushed carefully up into the outlet box.

• Conductor of a fan identified as grounded conductor to be connected to a grounded conductor of power

supply, conductor of fan identified as ungrounded conductor to be connected to an ungrounded conductor of

power supply, conductor of fan identified for equipment grounding to be connected to an

equipment-grounding conductor.

• CAUTION–To Reduce The Risk Of Electric Shock, Disconnect The Electrical Supply Circuit To The Fan

Before Installing Light Kit.

1 2

PARTS & ACCESSORIES

Canopy

Blade

Bulb

Downrod

Rod

Housing

Summary of content (6 pages)

PAGE 1
PARTS & ACCESSORIES Canopy INSTALLATION AND SAFETY INSTRCUTIONS Rod Downrod SAFETY PRECAUTION Bulb Blade Transmitter Kit Transmitter 5 4 1hr 6 3 3hr Transmitter Holder 1 2 Wall Screw x 2 2032 3V 6hr CR2032/3V Assembly Kit Expansion Bolt x 4 1 Battery CR • WARNING –To make sure power is off before attempting installation. • WARNING – Support Directly From Building Structure.
PAGE 2
INSTALLATION INSTRUCTION INSTALLATION INSTRUCTION Screw (14) STEP 1A - CONCRETE CEILING SWITCH OFF THE ELECTRICAL MAINS AT THE CIRCUIT BREAKER FUSE BOX. 1) Use the Mounting Bracket (1) as a guide, mark the spots where the 4 Expansion Bolts (2) will be drilled. 2) Remove the Mounting Bracket (1), drill 4 holes and insert 4 Expansion Bolts (2) into the concrete ceiling, install the mounting bracket and secure with Flat Washers (3), Spring Washers (4) and Nuts (5).
PAGE 3
INSTALLATION INSTRUCTION INSTALLATION INSTRUCTION STEP 2 Safety Wire Clamp 1) Remove the Clevis Pin (12), Nut (11), Spring Washers (10), Flat Washers(9) & Bolt (16) on Coupling (17). 2) Loosen the Screw (1) from Hanger Ball (3), remove the Hanger Ball (3) and Lock Pin (2). 3) Route the wires and safety wire from the motor through the Downrod (7). 4) Install the Downrod (7) to Coupling (17) and secure with Bolt (16), Flat Washer (9), Spring Washer (10), Nut (11) & Clevis pin (12).
PAGE 4
INSTALLATION INSTRUCTION FOR LIGHT N G FOR LIGHT L MOTOR U MOTOR V MOTOR W STEP 4 SWITCH OFF THE ELECTRICAL MAINS AT THE CIRCUIT BREAKER FUSE BOX. 1) Connect wires from receiver to power supply with wire connectors. 2) Insert the controller into the space of the mounting bracket, and tidy up the wiring. TRANSMITTER FUNCTION Light Fan TRANSMITTER SETTING This DC motor is equipped with self-learning frequency function transmitter. Read all the steps BEFORE proceeding.
PAGE 5
TRANSMITTER FUNCTION Forward / Reverse Fan speed (6 speed) Natural wind 5 4 1hr 6 3 3hr 1 2 6hr Power off Timer 6 3 1 2 Forward Reverse Fan rotates anti-clockwise creating a downward airflow delivering a cooling effect. Fan rotates clockwise creating an upward airflow moving warm air off the ceiling areas. This function works best at lower fan speed. Suitable for hot weather condition or air-conditioned condition.
PAGE 6
TECHNICAL SPECIFICATIONS MAINTENANCE Due to the fan’s natural movement, connections may get loose after a period of usage. To ensure a proper and safety usage, inspect the suspension system and tighten all connections every 6 months. Cleaning 647mm Cleaning your fan periodically will prolong its useful life. Basic cleaning procedures are as ≥ 1000mm follows: 1. Please shut off the power before you clean the light fan and replace the bulbs. 2.