User's Manual

ManualsBrandsGraco ManualsPumpsGraco 306520J - Fire-Ball 300 and Fire-Ball 425

Instructions – Parts List

GRACO INC.ąP.O. BOX 1441ąMINNEAPOLIS, MNą55440-1441

FIRE–BALL 300r and FIRE–BALL 425r

DRUM or TANK SUPPLY PUMPS

Used to pump petroleum and synthetic based oils.

5:1 Fire-Ball 300 Pump

Model 225852

900 psi (60 bar) Maximum Working Pressure

10:1 Fire–Ball 425 Pump

Model 225853

1800 psi (120 bar) Maximum Working Pressure

Table of Contents

Warnings 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operation 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts Drawing 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts Lists 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Warranty 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Graco Phone Number 10. . . . . . . . . . . . . . . . . . . . . . . . . .

306520J

Important Safety Instructions.

Read all warnings and instructions in this manual.

Save these instructions.

01494

Model 225852 Fire–Ball 300 shown

Summary of content (10 pages)

PAGE 1
Instructions – Parts List FIRE–BALL 300r and FIRE–BALL 425r DRUM or TANK SUPPLY PUMPS 306520J Used to pump petroleum and synthetic based oils. 5:1 Fire-Ball 300 Pump Model 225852 900 psi (60 bar) Maximum Working Pressure 10:1 Fire–Ball 425 Pump Model 225853 1800 psi (120 bar) Maximum Working Pressure Important Safety Instructions. Read all warnings and instructions in this manual. Save these instructions. Table of Contents Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 2
Symbols Warning Symbol Caution Symbol WARNING CAUTION This symbol alerts you to the possibility of serious injury or death if you do not follow the instructions. This symbol alerts you to the possibility of damage to or destruction of equipment if you do not follow the instructions. WARNING EQUIPMENT MISUSE HAZARD Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury. D This equipment is for professional use only.
PAGE 3
WARNING SKIN INJECTION HAZARD Fluid from the dispensing valve, leaks, or ruptured components can inject fluid into your body and cause extremely serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin can also cause serious injury. D Fluid injected into the skin may look like just a cut, but it is a serious injury. Get immediate surgical treatment. D Do not point the dispensing valve at anyone or at any part of the body.
PAGE 4
WARNING FIRE AND EXPLOSION HAZARD Improper grounding, poor ventilation, open flames, or sparks can cause a hazardous condition and result in a fire or explosion and serious injury. D Ground the equipment. Refer to Grounding below. D If there is any static sparking or you feel an electric shock while using this equipment, stop dispensing immediately. Do not use the equipment until you identify and correct the problem.
PAGE 5
Installation The typical installation shown in Fig. 2 is only an installation guide; it is not an actual system design. Contact your Graco distributor for assistance in designing a system to suit your needs. A Maximum vertical lift, tank foot valve to pump intake valve: 10 ft. (3 m) B Suction line at pump: 9 in. (230 mm) from wall C Suction line at pump: 6 in. (150 mm) above floor D Vent pipe E Pipe: 1.5 or 2 in. standard iron F Horizontal suction line: 75 ft. (23 m) maximum G Stub assembly H O.P.W.
PAGE 6
Installation Supply Lines From Pumps To Dispensing Units Distance Annealed Steel Tube Annealed Copper Tube Standard Iron Pipe Min. O.D. Min. Tube Wall Fittings Min. O.D. Min. Tube Wall < 25 ft. (7.6 m) 5/8 in. 0.035 in. (0.89) Flareless 5/8 in. type K 0.049 in. (1.24 mm) Flared 1/2 in. Heavy malleable iron > 25 ft. (7.6 m) 7/8 in. 0.035 in. (0.89) Flareless 7/8 in. type K 0.065 in. (1.65 mm) Flared 3/4 in. Heavy malleable iron > 75 ft. (23 m) A B C D Fittings Min.
PAGE 7
Installation Air and Fluid Line Accessories CAUTION Do not hang the air accessories directly on the air inlet. Mount them on brackets. The fittings are not strong enough to support the accessories and may break. D Use thread sealant on male threads except at swivel connections. D Install a bleed-type master air valve upstream from the pump air regulator, but within easy reach of the pump. To order a 300 psi (21 bar) maximum working pressure, 1/2 in. npt bleed-type master air valve, order Part No. 107142.
PAGE 8
Operation Pressure Relief Procedure WARNING INJECTION HAZARD To reduce the risk of serious bodily injury, including fluid injection, injury from moving parts, or splashing in the eyes or on the skin, always follow this procedure whenever you shut off the pump, when checking or servicing any part of the system, when installing or changing dispensing devices, and whenever you stop dispensing. 3. Disconnect the solvent supply, and connect the supply lines to the tank. 4.
PAGE 9
Parts Drawing 4 or 6 13 or 18 12 or 17 11 or 16 10 or 15 01498 Parts Lists Model 225852 Model 222062 5:1 Fire-Ball 300 Pump, Includes items 6, 7, 10 to 13 Hose Kit for Fire-Ball 300 pump Ref No. Part No. Ref No. Part No. 6 203876 7 222062 Description Qty. 5:1 FIRE-BALL 300 PUMP, stubby See manual 306518 for parts. 1 HOSE & FITTING KIT See parts list to the right. 1 10 204560 11 220598 12 155494 10:1 Fire–Ball 425 Pump, Includes items 4, 5, 15 to 18 13 155470 Ref No. Part No.
PAGE 10
The Graco Warranty and Disclaimers WARRANTY Graco warrants all equipment manufactured by it and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. As purchaser’s sole remedy for breach of this warranty, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment proven defective.