Assembly Instructions 18” 2-person assembly 63 ¾” PH #2 32” Model # Finish SH0501 Cherry SH0502 Expresso SH0504 Walnut Thank you for choosing Grain Wood Furniture, it is an honor to be in your home! If you have any questions, feedback, or need replacement parts please contact us at: grainwoodfurniture.com/help or support@grainwoodfurniture.
PLEASE READ BELOW BEFORE BEGINNING ASSEMBLY Ÿ Enlist help from a friend or family member as most items require two people for proper assembly. Ÿ Choose a spacious, open area near where the piece will be located once assembled. It is easier to move parts than to relocate the furniture after it is fully assembled. Ÿ Do not throw away packaging material until assembly is complete.
HARDWARE LIST A1 4,0x30 A4 3,5x14 A18 4,0x25 A25 M4x25 B31 6,0x10 C2 8,0x25 69 + 2 19 + 1 1 12 + 1 ANTI-TIPPING RESTRAINT KIT A8 3,0x20 2+1 F8 2 F9 1 48 + 2 76 + 2 1 D21 RIGHT Side E13 6 330mm - 13" Drawer RIGHT E13 6 330mm - 13" LEFT Side E14 6 330mm - 13" Drawer LEFT E14 6 330mm - 13" G1 10x10 27 G11 6 H4 12 ! ATTENTION Before starting assembly please verify the hardware set is complete. For missing hardware please contact us at grainwoodfurniture.
01 04 07 02 04 15 14 06 07 03 06 05 09 12 11 10 6x Part # 01 05 07 08 11 12 13 15 BOX A - 1 of 2 Description Top Lower crosspiece Back panel Drawer front Drawer bottom Drawer back Drawer bottom support Profile “H” Qty. 1 1 2 6 6 6 6 1 13 BOX B - 2 of 2 Part # Description Right side 02 03 Left side 04 Upper crosspiece 06 Rear crosspiece 09 Drawer right side 10 Drawer left side 14 Division HW Hardware 08 Qty.
1) Tip : Use a hammer in case dowels are hard to install by hand.
3) B31 B31 E13 B31 B31 B31 B31 E14 E14 B31 E14 B31 180º B31 14 B31 B31 B31 B31 6,0x10 12 E13 RIGHT Side E13 E13 E13 14 B31 B31 LEFT Side 3 E14 330mm - 13" 3 330mm - 13" 4) A1 04 A1 06 Attention: There are no predrilled holes for the A1 screws on parts 02 and 14.
5) Attention: There are no predrilled holes for the A1 screws on parts 02, 03 and 14. A1 04 A1 A1 A1 06 04 A1 A1 A1 03 05 06 A1 4,0x30 A1 6 Attention: There are no predrilled holes for the A1 screws on part 01. 6) A1 A1 A1 A1 A1 A1 01 A1 A1 A1 A18 05 A1 A1 A18 4,0x30 Attention: There are no predrilled holes for the A18 screws on part 05.
Make sure back panels are perfectly aligned with side panels and top and there are NO gaps.
) 15 07 07 15 6 G11 10) G1 07 G1 10x10 22 page 9/14
11) A4 A4 A4 A4 06 07 A4 A4 A4 06 A4 Attention: There are no predrilled holes for the A4 screws on parts 06 and 07. A4 3,5x14 7 12) A4 A4 A4 A4 A4 A4 A4 A4 A4 A4 Attention: There are no predrilled holes for the A4 screws on parts 02, 03 and 14.
13) 6x 10 A1 09 A1 A1 08 11 Attention: There are no predrilled holes for the A1 screws on part 08.
Flip the assembled drawer upside down to install glides.
16) Place the labeled drawer on the top position ! page 13/14
ANTI-TIPPING RESTRAINT KIT 17) ! Install against the furniture A8 on the wall A8 F8 F8 F9 WALLBOARD Anchors and screws are not included, choose best type based on your wall F8 A8 3,0x20 2 F8 2 F9 1 WALLBOARD Install both parts F8 Tighten them together using the safety strap page 14/14
