Grandstream Networks, Inc.
TABLE OF CONTENTS MOBOTIX T24S SYSTEM CONFIGURATION GUIDE FOR GXV3140 INTRODUCTION: .............................................................................................................................................. 3 INITIAL SETUP FOR A NEW “GXV-3140/T24S SYSTEM” DOOR SYSTEM: ................................................. 3 DISCOVER/CONFIGURE A GXV-3140 PHONE AUTOMATICALLY WITH AN EXISTING DOOR SYSTEM ... 5 ADD/CONFIGURE A NEW GXV-3140 MANUALLY : .............................................
INTRODUCTION: This guide has been tested for Grandstream GXV3140 IP Video Phone with firmware version 1.0.7.50 and Mobotix T24S Door System with MX-V4.1.1.7 (2011-12-15) Software. Be aware that different firmware revisions may have different web interface formats and functionalities. This guide is applicable to the following Grandstream phone models: GXV3140. This guide will cover the 3 possible ways to set up a phone for use with Mobotix T24S.
3. Connect the GXV-3140 and T24S Door Station to the switch/router as shown below : Figure 2: Connecting the GXV-3140 and T24S 4. The buttons will light up for four seconds. During this time, press the doorbell button (bottom button) until that it starts flashing. This starts automatic initial configuration, which will take around 5 minutes: The T24S lights blink as the camera starts up. The current T24S IP addresses and network data are announced automatically.
Figure 3: GXV3140 “provisioned by Mobotix” LCD Idle Screen 5. The T24S Door Station and GXV-3140 phone are now ready. Here is a summary of the changes made automatically on both the GXV-3140 and T24S Door Station: SIP server in the T24S is activated automatically. GXV-3140 IP Video phone and the T24S are configured to use DHCP, and are automatically assigned an IP address and SIP quick-dial number.
Figure 4: Add a new GXV-3140 Note: GrandStream “*101” is the extension that was configured during the initial configuration. 2. Press the + sign in order to add a new phone, you will now have another field, choose Search Door Stations Devices as shown below: Figure 5: Discover the new added GXV-3140 Grandstream Networks, Inc. www.grandstream.
Once the search is done you will be prompted with the list of the available GXV-3140 on your network, as shown below: Figure 6: Discovery Result 3. Select the phone you want to add to your system, once your press OK and confirm the action, the phone will reset and get configured automatically. Note: When you configure the phone using one of the above two method described, you may at anytime lift the GXV3140 handset which will trigger a call to your T24S System.
Figure 7: Example of your Door System ADD/CONFIGURE A NEW GXV-3140 MANUALLY: This section details how you can configure your GXV-3140 with the Mobotix T24S System manually. To do so, please proceed as follows: 1. First, ensure that you have created the extension that you wish to use with the phone in T24S. Here is a quick description on how to create the extension on the Mobotix T24S System : a.
Figure 8: T24S Mobotix SIP Server settings Make sure that SIP server is on, and take a note of the SIP server IP and the port that will be used on the phone configuration. b. Add a new extension on T24S : Figure 9: Add a new extension on T24S Grandstream Networks, Inc. www.grandstream.
c. Once the Add new SIP account is pressed, the blank field will appear please configure the SIP address/User Name/ Password you wish to use: Figure 10: Extension Settings on T24S d. Once done, please update the configuration by pressing the Set button. 2. Connect the GrandStream GXV-3140 video phone to the network and to the power. The phone will boot up, and request an IP address from your DHCP server. Once the phone gets an IP address it will display on its idle screen. 3.
Figure 11 – Login Page of a GXV phone 5. The GXV-3140 offers you the possibility to configure 3 SIP accounts, you may configure the extension from the T24S Door System on any account, in this example we will configure it using the second Account. 6. Now you can configure the “Account 2” settings. First of all, make sure that „Account Active‟ is set to YES. Enter an account name for the phone in the „Account Name‟ box. This setting is not used by T24S Door System.
Figure 2: Account 2 Configuration on the GXV phone. 7. In the SIP server field, enter the IP or FQDN of the Mobotix T24S Server. 8. Repeat the same setting for the Outbound Proxy option 9. Enter the extension number you want to associate with this phone in the ‘SIP User ID’ settin Figure 12 – Account configuration on the GXV-3140 7. Now enter the „Username‟ & „Password‟ in the appropriate fields as shown in the above figure 13. 8.
Figure 3: Mobotix Special Feature 13. Scroll to the bottom of the page and press ‘Save’ to save these settings and then press ‘Apply’ in order for the changes to take effect; the phone should now be fully compatible with the Mobotix T24S. Figure 13 – Mobotix Special Feature configuration 10. Save and apply the new configuration, the GXV-3140 should be registered correctly with the T24S Sip Server.
- Main Menu of the call screen: Once the call is established between the GXV-3140 and the T24S camera, the camera image appears automatically along with the user menu. The main menu will appear on the left side of the call screen as shown below: Figure 14: Main Call Screen The Menus will be controlled using the Keypad of the phone (“using the 12 keys (0-9 * and #) and the navigation key of the phone “). Note: The Navigation keys are mapped as shown in figure 14 The status display appears at the top left.
The info icons displayed on the phone are described as follows: Info icon Description Open door Function The door is open Closed door The door is closed, but not locked Lock The door is closed and locked Red lock Door sensor error: Check door status! Incandescent lamp The external light is on (e.g. the lamp above the door) Microphone The telephone microphone is disabled. Buzzer The one-minute record function is active.
Pan-Tilt-Zoom (Digital PTZ): Key 2 or 8 (push 1x, 2x, 3x): Camera digitally pans by 1//, 2/3 and 3/3 of a step (maximum) up or down; Key 0: Display the main menu and return to panorama image (initial view); Key 4 or 6: Switch to zoomed 4:3 image with simultaneous pan to left or right; after pushing key 5 (digital zoom) 1x, you can zoom in or out on the displayed image segment using keys 2 or 8; pushing key 5 again returns you to tilt mode (keys 2 and 8); Grandstream Networks, Inc. www.grandstream.
