Owner manual

ManualsBrandsGReddy ManualsCarINTERCOOLERS: Nissan GTR 2009- / Type29R

INTERCOOL

INTERCOOLINTERCOOL

INTERCOOLER

ERER

KIT

KITKIT

KIT

ＮＩＳＳＡＮ

ＮＩＳＳＡＮＮＩＳＳＡＮ

ＮＩＳＳＡＮ

ＧＴ－Ｒ

ＧＴ－ＲＧＴ－Ｒ

ＧＴ－Ｒ

Ｒ

ＲＲ

Ｒ３５

３５３５

３５

（ＶＲ

（ＶＲ（ＶＲ

（ＶＲ３８

３８３８

３８ＤＥＴＴ）

ＤＥＴＴ）ＤＥＴＴ）

ＤＥＴＴ）

ＳＰＥＣ－Ｒ

ＳＰＥＣ－ＲＳＰＥＣ－Ｒ

ＳＰＥＣ－Ｒ

ＨＧ

ＨＧＨＧ

ＨＧ

ＴＹＰＥ

ＴＹＰＥＴＹＰＥ

ＴＹＰＥ２９

２９２９

２９

Ｆｕｌｌ

ＦｕｌｌＦｕｌｌ

Ｆｕｌｌ

ＫＩＴ

ＫＩＴＫＩＴ

ＫＩＴ

• Please read the Installation Manual before installing.

Please read the Installation Manual before installing.Please read the Installation Manual before installing.

Please read the Installation Manual before installing.

• Keep this manual for future reference.

Keep this manual for future reference.Keep this manual for future reference.

Keep this manual for future reference.

Model Chassis Code Engine Code Year

ＧＴ－ＲＣＢＡ－Ｒ３５ＶＲ３８ＤＥＴＴ０７．１２～

Specs

Specs Specs

Specs ：

：：

：

Cross

CrossCross

Cross-

-fl

flfl

flow Type

ow Typeow Type

ow Type

Designed for the Greddy Turbo Kit

Designed for the Greddy Turbo KitDesigned for the Greddy Turbo Kit

Designed for the Greddy Turbo Kit（

（（

（TD

TDTD

TD ０６

０６０６

０６ SH

SHSH

SH-

-２０

２０２０

２０ G

G）

））

）

 If used with the OEM Turbo, GReddy Airinx Kit required.

Not compatible with the stock air box.

 Stock windshield washer tank not compatible with GReddy Intercooler Kit.

GReddy Windshield Washer Tank sold separately.

 Stock Intercooler Air Duct is not compatible with GReddy Intercooler Kit.

Installation Manual

Installation ManualInstallation Manual

Installation Manual

Designed to be used on the Nissan R35 GTR. Please do not

attempt to use on other model vehicles.

Using this product may void your warranty from Nissan M

Using this product may void your warranty from Nissan MUsing this product may void your warranty from Nissan M

Using this product may void your warranty from Nissan Motor Co., Ltd. Corporation

otor Co., Ltd. Corporationotor Co., Ltd. Corporation

otor Co., Ltd. Corporation

Summary of content (18 pages)

PAGE 1
INTERCOOLER INTERCOOLER KIT ＮＩＳＳＡＮＧＴ－ＲＲ３５（ＶＲ３８（ＶＲ３８ＤＥＴＴ）３８ＤＥＴＴ）ＳＰＥＣ－ＲＨＧＴＹＰＥ２９ＴＹＰＥ２９ＦｕｌｌＫＩＴ Installation Manual • Please read the Installation Manual before installing. • Keep this manual for future reference. Model Chassis Code Engine Code Year ＧＴ－ＲＣＢＡ－Ｒ３５ＶＲ３８ＤＥＴＴ０７．１２～ Specs ： CrossCross-flow flow Type Designed for the Greddy Turbo Kit（ Kit（TD ０６ SHSH-２０ G） If used with the OEM Turbo, GReddy Airinx Kit required. Not compatible with the stock air box.
PAGE 2
１．Parts List １．Intercooler ＴＹＰＥ－２９ 1 ２．Intake tube Ｉ－１（７０ φ aluminum elbow） 1 ３．〃Ｉ－２（７０ φ aluminum） 1 ４．〃Ｉ－３（７０ φ aluminum） 1 ５．〃Ｉ－４（７０ φ aluminum） 1 ６．〃Ｉ－５（７０ φ aluminum elbow） 1 ７．〃Ｉ－６（７０ φ aluminum） 1 ８．〃Ｉ－７（７０ φ aluminum） 1 ９．〃Ｉ－８（７０ φ aluminum） 1 １０．Silicone hose ７０ φ×７０㎜ 12 ＃４４ 24 １１．Hose clamp １２．Intake tube bracket ＲＨ 1 １３．Intake tube bracket ＬＨ 1 １４．Wire Harness （１０００㎜） 8 １５．Bolt Ｍ６×１５㎜Ｐ１．０ 2 １６．Bolt Ｍ８×２０㎜Ｐ１．２５ 4 １７
PAGE 3
Parts List Diagram １２３４５６７１０８９１１１２ ―２― １３
PAGE 4
１４１５～１９２０ Blow Off Valve Parts List １． Blow off valve ×２６． Hose Clamp size #16 ×４２． Hose attachment ２９ φ ×２７． Blow off valve gasket ×２３． Rubber cap ３０ φ ×２８． Emblem ×２４． Vacuum hose ６ φ×３００㎜ ×２９． Bolt and washer ×４５． Power band ６ φ ×４ Parts List Diagram １２３４６７８９ ―３― ５
PAGE 5
Piping Layout Throttle RH Throttle LH №5 I-４ №20 Blow Off Valve №9 I-8 №20 Blow Off Valve Turbo LH №6 I-5 Turbo RH №2 I-1 №7 I-6 №8 I-7 №4 I-3 №3 I-2 ―４―
PAGE 6
２．Removal of Stock Parts ２－１ Front Bumper Removal (1) Disconnect the negative terminal of the battery. If the car was recently shut off, please wait 3 minutes before disconnecting the battery. (2) Remove the front, the inner, the left and the right inner fender protectors. (3) Remove the one-piece lip spoiler/ undercarriage cover. ※ Remove the rubber plugs to expose the bolts and screws. ※ Slide the one-piece lip spoiler/ undercarriage cover forward (away from the car) to remove.
PAGE 7
(7) Remove the connector from the pedestrian impact sensor. ※ If the battery is reconnected while the pedestrian impact sensor is disconnected, a popup hood warning light will appear on your instrument panel. (8) Remove the bumper/ fascia. ※ Be aware of the bumper fasteners, some adjustment required to remove the bumper/ fascia. ２－２ Air Intake Duct Removal (1) Remove the engine oil cooler duct. ※ Allow the oil cooler to hang freely. (2) Remove the left and right intake duct.
PAGE 8
(3) Remove the impact foam. (4) Remove the front bumper reinforcement. アーマチュア取り付けボルト×８バンパーブラケット取り付けボルト×４ ※Air duct mounting bolts are attached to the front bumper reinforcement, please remove. (5) Disconnect the couplers. Horn (6) Remove the hood latch cable and cable fastener. ・・・Electrical Couplers A/C Liquid Tank, Outside Temp. Sensor Hood Latch, Horn A/C Liquid Tank ・・・Cable fastener Temp Sensor ・・・Hood :Lock Cable Fastener Hood Latch (7) Remove the front bumper retainer (upper side).
PAGE 9
(8) Remove the P/S Oil Cooler mounting bolts, and let the cooler hang freely. ※ Removal of oil line is not necessary. ※ Be careful not to damage the oil cooler and A/C condenser. (9) Disconnect the windshield washer pump and washer liquid level switch connectors. Remove the front Washer Tube Pump from the Pump. Remove the washer liquid level switch fastener。 Tube Clip Liquid Switch (10) Remove the washer tank.
PAGE 10
(12) Remove the radiator air guide bolts. Once removed, uninstall the Intercooler(s) and radiator core support. Remove the driver side (U.S.). Then remove completely. Make sure not to hit or damage the oil cooler. ※Slightly move the radiator core support frame. Once moved, disconnect the Hood Latch Cable Fastener. ２－３ Intercooler Removal (1) The arrows show the rivets that will need to be drilled out. Once the rivets are drilled out, please remove the Intercooler Intake Duct.
PAGE 11
３．Intercooler Install ３－１ Intercooler Core Installation (1) Temporarily install the intercooler on to the radiator core support and mark the areas where the intercooler hits the №1 support. (2) Drill out the areas where the radiator core support hits the intercooler. (3) Install the intercooler on to the radiator core support using part # 1, 18, & 19. (4) Verify that the radiator core support has been drilled out in order to achieve proper clearance.
PAGE 12
３－３ Intercooler Side Intake Tube Installation (1) Remove the rubber and steel insulated grommets from the stock intake piping, and install them onto the intercooler mounting brackets part # 12 & 13. Grommets No.12 No.13 (2) Arrange the intercooler piping in the as shown in the diagram. ※ Follow the arrows on the intercooler piping for proper orientation. ※ Temporarily attach the piping loosely. Carefully make adjustments as needed.
PAGE 13
３－４ Throttle Side Intake Tube Installation (1) Install the RZ Blow Off Valves onto intake tubes I-4 & I-8 ※ Make sure to arrange the Blow Off Valve outlets in the direction towards the pressure sensors. I-8 (2) I-4 Disconnect the pressure sensors from the stock piping and install them onto Intercooler Pipes I-4 & I-8. ※ We recommend applying silicone grease to the pressure sensor O-rings. M6×15 (3) M6×15 Blow Off Valve Attachment Selection. Recirculated Install the Hose Attachment.
PAGE 14
(2) Temporarily attach intake tube I-8 assembly between the ＲＨ passenger side throttle body and I-7 using the 70mm hose No.10 No.11 #10 and hose clamps #11. Connect the OEM recirculation hose to the 28mm tube of the turbo inlet intake tube using the hose clamp #6 (BOV parts list) to the Hose Attachment. (3) Temporarily attach intake tube I-4 assembly between the driver side throttle body and I-3 using the 70mm hose #10 ＬＨ No.10 No.11 and hose clamps #11.
PAGE 15
(2) Temporarily attach intake tube I-8 assembly between ＲＨ the passenger side throttle body and I-7 using the 70mm No.10 No.11 hose #10 and hose clamps #11. (3) Temporarily attach intake tube I-4 assembly between ＬＨ the driver side throttle body and I-3 using the 70mm No.10 No.11 hose #10 and hose clamps #11. ３－５ Vacuum Line Attachment (1) Connect the 6mm vacuum lines from the vacuum source to the tops of the RZ Blow Off Valves. Connect the pressure sensor couplers to the pressure sensors.
PAGE 16
３－６ Air Flow Sensor Extension Harness (1) Remove the coupler and the wiring clip of the Air Flow Sensors. (2) Cut the Air Flow Sensor Harnesses 2 inches from the Coupler. The Air Flow Sensor Harnesses will have to crossed and hardwired via solder. Please use the supplied wiring Part #14. (3) The left and right Air Flow Sensor Harnesses will have to redirected to the opposite sides. ※ Be sure to properly solder the connections.
PAGE 17
３－８ Front Bumper/ Fascia Installation (1) Remove the front bumper bracket from the intake duct. (2) Reinstall the bumper reinforcement and reuse the front bumper brackets. (3) Washer Tank (sold separately)。 separately) ※ Refer to washer tank installation manual。 (4) Front bumper/ fascia reinstallation. ※ ２－１ Follow pages 55-6 in reverse order.
PAGE 18
Adjustments After Installation If irregular idle or engine stall occurs, loosen the M6 lock nut and turn the adjustment screw to HARD until the problem is eliminated. After the adjustment, tighten the lock nut to secure the setting. ※ The adjustment is preset to the softest position form factory. Do not turn it further out that this position. ※ Make sure to loosen the lock nut before making adjustment. Turning the adjusting screw without loosening the lock nut will strip out the top housing.