P0802371-02 Rev B 2101202 EN STRING TRIMMER OPERATOR MANUAL FR COUPE-HERBE MANUEL DE L’UTILISATEUR ES CORTABORDES MANUAL DEL OPERADOR STB456 www.greenworkstools.
English 1 1.1 1.2 1.3 2 3 4 5 6 7 8 8.1 8.2 8.3 8.4 8.5 8.6 9 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 Description......................................... 4 Purpose.............................................................. 4 Overview........................................................... 4 Packing list........................................................ 4 Important safety instructions...........4 Symbols on the machine................... 5 Risk levels...........................................
English EN 1 DESCRIPTION 1.1 PURPOSE 2 READ ALL INSTRUCTIONS BEFORE USING (THIS POWER TOOL) This machine is used to cut grass, light weeds, and other similar vegetation at or around ground level. The cutting plane must be approximately parallel to the ground surface. You cannot use the machine to cut or chop hedges, shrubs, bushes, flowers and compost. 1.2 WARNING Read and understand all instructions before using this product.
English • • • • • • • • • • • • • Check damaged parts before using the appliance, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, damaged mountings, and any other condition that may affect its operation.
English EN 4 RISK LEVELS WARNING If the battery pack cracks or breaks, with or without leaks, do not recharge it and do not use. Discard it and replace with a new battery pack. DO NOT TRY TO REPAIR IT! To prevent injury and risk of fire, explosion, or electric shock, and to avoid damage to the environment: The following signal words and meanings are intended to explain the levels of risk associated with this product.
English EN WARNING • • • 4 If parts of the machine are damaged, do not use the machine. If you do not have all the parts, do not operate the machine. If parts are damaged or missing, contact the service center. 2 3 5 1 4. Turn the lower shaft until the button locks into the positioning hole. 1. Open the package. 2. Read the documentation provided in the box. 3. Remove all the unassembled parts from the box. 4. Remove the machine from the box. 5.
English EN 9.1 4. Tighten the screws. START THE MACHINE 1. Push the lock-out lever (1) and pull the trigger (2). 1 2 8.5 INSTALL THE BATTERY PACK • If the battery pack or charger is damaged, replace the battery pack or the charger. Stop the machine and wait until the motor stops before you install or remove the battery pack. Read and understand the instructions in the battery and charger manual. WARNING • • 9.2 STOP THE MACHINE 1. Release the trigger to stop the machine. 9.3 1.
English 9.4 ATTACH MACHINE TO SHOULDER STRAP • • EN Remove the battery pack. Remove the grass. 2 1 1 2 1. Attach the carabiner to the carrying ring on the drive tube. 1 9.6 • • • • • 2 2. Put on the shoulder strap. 3. Adjust the length of the strap so that the carabiner is about a hand’s width below your right hip. 9.5 OPERATION TIPS WARNING Keep clearance between the body and the machine. WARNING Do not operate the machine without guard in place.
English EN 9.7 ADJUST THE CUTTING DIAMETER 10.1 IMPORTANT NOTE Only your dealer or approved service center can do the maintenance that is not given in this manual. The machine is set at a 14" (356 mm) cutting diameter. You can adjust to a 16" (406 mm) cutting diameter. Before the maintenance operations: Set the cutting diameter to 14" (356 mm) for greater runtime and 16" (406 mm) for a larger cutting area. • • • • • 1. Remove the battery pack. 2.
English EN 3. Put the cutting line through the hole. Push the cutting line until it exits the opposite hole. 1 2 1 2 3 4 3. Remove any remaining line. 4. Pull the cutting line through until there is an equal quantity of cutting line on each side. 4. Clean dirt and debris from all parts. Replace spool (3) if it is worn or damaged. 5. Align the spool tabs with the tab openings in the base of the spool (4). 6. Push the spool cover until it clicks into position. 5.
English EN 11 TRANSPORTATION AND STORAGE WARNING 1 Remove the battery pack from the machine before transportation and storage. 11.1 MOVE THE MACHINE When you move the machine, you must: • • Stop the machine. Remove the battery pack. 11.2 • • • 2. Turn the trimmer head clockwise to loosen it. Do not remove the spacer from the shaft. • 12 10.6 STORE THE MACHINE Remove the battery pack from the machine. Make sure that children cannot come near the machine.
English Problem Possible Cause The machine stops when you cut. The guard is not Remove the battery pack attached to the ma- and attach the guard to chine. the machine. Solution EN Problem Possible Cause Solution The line keeps breaking. The machine is used incorrectly. 1. Cut with the tip of the line, avoid stones, walls and other hard objects. Heavy cutting line Use only with the nylon is used. cutting line of 0.08" (2 mm) diameter. The grass winds around the motor shaft or the trimmer head.
English EN Item Temperature Greenworks Tools Greenworks Tools Canada Inc. Battery storage temperature range 32°F (0°C) - 113°F (45°C) P.O. Box 1238 P.O.
English 15 EN EXPLODED VIEW 2 1 3 5 4 No. Part No. Qt y Description No. Part No.
