ELECTRIC 3⁄16" CROWN STAPLER MODEL H3119 INSTRUCTION MANUAL COPYRIGHT © OCTOBER, 2002 BY GRIZZLY INDUSTRIAL, INC. 1821 VALENCIA ST., BELLINGHAM, WA 98227 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • • • Lead from lead-based paints. Crystalline silica from bricks, cement, and other masonry products. Arsenic and chromium from chemically treated lumber. Your risk from these exposures varies, depending on how often you do this type of work.
SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
Safety Instructions For Power Tools 9. USE PROPER EXTENSION CORD for the tool. Make sure your extension cord is in good condition. Conductor size should be in accordance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Your extension cord must also contain a ground wire and plug pin. Always repair or replace extension cords if they become damaged.
INTRODUCTION Commentary Lack of familiarity with this manual could cause serious personal injury. Spend a sufficient amount of time becoming familiar the contents of this manual, including all the safety warnings. We are pleased to provide this manual with the Model H3119. It was written to encourage safety considerations and guide you through general operating procedures and maintenance. This manual represents our effort to produce the best documentation possible.
OPERATION Getting Started Please take the time to become familiar with this instruction manual. The information contained will allow you to get the maximum enjoyment and use from your new tool. Loading The Stapler The Model H3119 can hold up to 85 staples in the quick loading magazine. Using The Stapler DO NOT pull the trigger until the tip of the stapler is against the surface to be stapled. The stapler does NOT have a safety mechanism. 1.
Clearing Jammed Staples Maintenance Staple jams are an inevitable part of operating any stapler. Unplug the stapler from the power source before performing any maintenance! To clear a jammed stapler: 1. Unplug the tool from the power source! 2. Open the staple magazine and remove all un-jammed staples. Cleaning The Stapler While wearing safety glasses, periodically clean the stapler with compressed air. DO NOT use flammable products to clean the stapler. 3.
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
REF PART # DESCRIPTION REF PART # DESCRIPTION 01 PH3119001 CYLINDER CAP ASSEMBLY 29 PH3119029 SPRING 02 PH3119002 PLUNGER 30 PH3119030 BASE 03 PH3119003 PIN 31 PH3119031 MAGAZINE SUPPORT 04 PH3119004 PLUNGER BLADE 32 PH3119032 PIN 05 PH3119005 PLUNGER RET.
NOTES H3119 Electric 3⁄16" Crown Stapler -9-
NOTES -10- H3119 Electric 3⁄16" Crown Stapler
WARRANTY CARD Name __________________________________________________________ Street __________________________________________________________ City____________________State________Zip_________ Phone Number____________E-Mail___________________FAX____________ Model #___________________________ Serial #______________________ The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services.
Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O.