Product Manual

ManualsBrandsGrundfos Pumps ManualsElectricGrundfos 5SQ07-270 - 5 GPM 3/4 HP SQ-Series Deep Well Submersible Pump (270' Rated Head) (2W - 200-240V)

Table Of Contents

1. SQ, SQE introduction
- SQ, SQE features and benefits
- SQ, SQE identification
  - Type key example SQ, SQE
2. SQ, SQE applications
- SQ with pressure switch and pressure tank
- Constant-pressure control with CU 301, residential water supply
- Constant-pressure control with CU 301, irrigation
- Maintaining a constant water table
- Emptying or filling a tank
- Pumping from one tank to another
- Setting of operating parameters
- SQE with manual speed control
3. Performance range
4. SQ, SQE installation
5. Sizing and selection
- System sizing guide
6. Cable sizing
- Cable sizing chart
7. SQ, SQE curve charts
- 5 SQ, SQE
- 10 SQ, SQE
- 15 SQ, SQE
- 22 SQ, SQE
- 30 SQ, SQE
8. SQ, SQE technical data
- Electrical data
  - Control units CU 300 and CU 301
- Operating conditions
  - Storage conditions
- Motor data
- Dimensions and weights
  - SQ, SQE
9. SQ, SQE construction
- Materials of construction
- SQ, SQE material specification
- Control units for SQ, SQE
- CU 301
- CU 300
10. CU331SP variable frequency drive
- Features
  - User interface
  - Functions
- Applications
- System components
- Identification
  - Nameplate
- CU331SP product range
- CU331SP performance range
- CU331SP sizing
- CU331SP operation
- CU331SP installation
  - Mechanical installation
- CU331SP electrical connection
- CU331SP technical data
- CU331SP curve charts
11. Accessories
- CU 301 Constant Pressure System
- CU 300 Status Box & R100
- SQ, SQE flow sleeves
12. SP introduction
- Introduction
- Applications
  - Pumped liquids
- Features and benefits
- Identification
13. SP product overview
- SP performance range 60 Hz
- Pump range
- Motor range
- Motor protection and controllers
14. SP construction
- Sectional drawing, SP pump 4" spline shaft
  - Material specification
- Sectional drawing, SP pump 4" smooth shaft
- Sectional drawing, SP pump 6" (SP 85S - 300S)
  - Material specification
- Sectional drawing, SP pump 8" (SP 385S - 475S)
  - Material specification
- Sectional drawing, SP pump 10" (SP 625S - 1100S)
  - Material specification
- Sectional drawing, MS motors
  - Material specification, MS 402, MS 4000, and MS 6000C motors
  - R-version motor
- Sectional drawing, MMS motors
15. SP operating conditions
- Operating conditions
  - Maximum liquid temperature
  - Operating pressure
- Curve conditions
  - General
16. How to read the curve charts
17. SP curve charts and technical data
- 4" and larger wells
- SP 5S (5 gpm)
- SP 7S (7 gpm)
- SP 10S (10 gpm)
- SP 16S (16 gpm)
- SP 25S (25 gpm)
- SP 35S (35 gpm)
- SP 45S (45 gpm)
- SP 62S (62 gpm)
- SP 77S (77 gpm)
- 6" and larger wells
- SP 85S (85 gpm)
- SP 150S (150 gpm)
- SP 230S (230 gpm)
- SP 300S (300 gpm)
- 8" and larger wells
- SP 385S (385 gpm)
- SP 475S (475 gpm)
- 10" and larger wells
- SP 625S (625 gpm)
- SP 800S (800 gpm)
- SP 1100S (1100 gpm)
18. SP electrical data
19. Accessories
- MP 204
  - Applications
  - Benefits
- Control functions
- CU331SP constant pressure drive kits
  - Grundfos GO remote app and Grundfos GO CAPS
- Connecting pieces
  - Thread-to- thread
- Zinc anodes
- SA-SPM 6 control boxes
- Pt100
20. Energy consumption
- Energy consumption of submersible pumps
21. Cables
- Cable sizing charts
22. Friction loss tables
23. Grundfos Product Center

SQ, SQE installation

SQ, SQE, CU 331, and SP

4. SQ, SQE installation

The SQ and SQE may be installed vertically,

horizontally or in any position in between.

Note: The pump must not fall below the horizontal

level in relation to the motor.

The following features ensure simple installation of the

pump:

• Built-in check valve with spring

• low weight ensuring user-friendly handling

• installation in 3" or larger boreholes

• only on/off switch is needed, which means that no

extra motor starter / starter box is necessary.

For horizontal installation a flow sleeve is

recommended in order to:

• ensure sufficient flow velocity past the motor and

thus provide sufficient cooling

• prevent motor and electronic unit from being buried

in sand or mud.

Fig. 13 SQE installation

TM01 1375 1498

Allowed

Not allowed