Operation Manual

9
Sonoclock 42/42 Q page 9
GB
Alarm Time 1 / Alarm Time 2
• Select the alarm time(s) with switch ALARM 1/2:
ALARM 1 = alarm time 1 (indicated by light
dot ALARM 1 6 )
ALARM 2 = alarm time 2 (indicated by light
dot ALARM 2 6 )
ALARM 1+2 = both alarm times activated
(indicated by both light dots
ALARM 1 6 and ALARM 2 6 )
Wake-up by radio
• Switch on the radio with the RADIO ON button.
• Select a station which will be broadcasting at
the alarm time and adjust the volume to the
required level.
•
Switch off the radio with the RADIO/ALARM
OFF button.
• Set the function selection switch
ALARM /ɷ/OFF to position ɷ.
–
At the preselected alarm time(s) the
radio will switch on and switch off
again automatically 59 minutes later.
Wake-up by sound signal
• Set the function selection switch
ALARM /ɷ/OFF to position .
–
At the preselected alarm time(s) the
sound signal will switch on and
switch off again automatically 59 minutes later.
– The two alarm signals for alarm time 1 and
alarm time 2 differ in tone.
ALARM
OFF
ALARM
OFF
ALARM 1+2
ALARM 2ALARM 1
1
2
ALARM
Positioning the set
Caution should be exercised if the set is placed
on furniture as surfaces are often coated with
lacquers and plastic finishes containing additives
which attack the material of which the feet of the
set are made, leaving stains which can only be
removed with difficulty or not at all.
Further notes:
• Only a soft cloth which picks up dust should
be used to clean the cabinet. Do not use
aggresive polishes or cleaning agents.
• Do not expose the unit to moisture
(e.g. dripping or splashing).
• The type label is on the bottom of the unit.
Technical specifications
Wavebands: FM ................87.5 – 108 MHz
MW..........526.5 – 1606.5 kHz
LW..............148.5 – 283.5 kHz
Power output:................800 mW peak power
The unit meets the CEE regulations concerning
interference radiation.
This product fulfills European directives
89/336/EEC, 73/23/EEC and 93/68/EEC.
This set complies with the safety regulations
according to VDE 0860 / BS 415 and thus
with the international safety regulations
according to IEC 65.
Subject to technical alterations and alterations
in styling. E & O.E.
Interrupting and repeating the
alarm
• The radio alarm or electronic sound alarm can
be interrupted with the SNOOZE button.
– After 7 minutes, the alarm comes on again.
• It is possible to interrupt the alarm function
several times during the switch-on period.
– The alarm remains set to operate the next day.
Switching off the alarm
• The alarm function can be switched off by
pressing the RADIO/ALARM OFF button.
– The alarm remains set to operate the next day.
• If you wish to switch off the alarm
completely, set the function
selection switch ALARM /ɷ/
OFF
to position OFF.
– The
light dots ALARM 1 6 and ALARM 2 6
go out.
Going to sleep while listening to
the radio
• Press the SLEEP button briefly.
– The unit switches on the radio and the display
will show the previously set 'sleep' period.
• The 'sleep' time can be adjusted between 0
and 59 minutes by keeping the SLEEP button
pressed and then pressing the 1 and 22
buttons.
• If only the SLEEP button is held pressed for
more than 3 seconds, the 'sleep' time can be
reduced automatically (down to '0').
– After the preset sleep time has elapsed, the
radio will switch off automatically.
•
The SLEEP function can be terminated prematurely
by pressing the RADIO/ALARM OFF button.
ALARM
OFF
ALARM GENERAL