CLOCK RADIO Sonoclock 660 PLL EN
________________________________________________________ ALARM 1 ALARM 2 MEM/TIME COLOUR ON/OFF RDS/WEC SLEEP/NAP DISPLAY DIMMER 0 –P SNOOZE P+ C AUTO DIMMER DISPLAY BATTERY ANTENNA RESET Ü 3 ENGLISH &TUNING%
_______________________________________________________ ENGLISH 4 ENGLISH 05 -17
SET-UP AND SAFETY_ __________________________ 7 This device is designed for the When deciding where to place 7 playback of audio signals. Any other use is expressly prohibited. 7 the device, please note that furniture surfaces are covered by various types of varnish and plastic, most of which contain chemical additives. These additives may cause corrosion to the feet of the unit and leave stains on the surface of the furniture which could be difficult or impossible to remove.
OVERVIEW________________________________________ See the figure on page 3. ON/OFF Switches the radio to and from standby mode. COLOUR Switches between eight different colours for the display backlight. ALARM1 Activates the setting for alarm time 1. DIMMER Adjusts the brightness of the display to one of three levels, switches off the backlight for the display. RDS/WEC Switches between different RDS station information bulletins in radio mode.
OVERVIEW________________________________________ DISPLAY Displays the current time, date, the alarm times and FM station information. P– Selects the next preset down. AUTO DIMMER Automatically adjusts the brightness of the display to the brightness of the surroundings. 0 Headphone jack for connecting headphones or an earphone set with a jack plug (ø 3.5 mm). The speaker on the unit is switched off.
POWER SUPPLY_________________________________ Mains operation Check that the mains voltage on the type plate (on the bottom of the device) corresponds to your local mains supply. If this is not the case, contact your specialist dealer. 1 Plug the mains cable into the sock��et (230 V~, 50/60 Hz). Caution: 7 The device is connected to the mains with the power cord. Pull out the power cord when you want to completely disconnect the device from the mains.
SETTINGS__________________________________________ First installation When the device is connected to the mains for the first, time, an automatic station search starts. Stations are automatically saved to the presets. At the end of the search a demo program starts. To end the demo program, press »ON/OFF«. The station saved on preset position 1 can be heard. If the device receives a station that transmits an RDS time signal, the time and the week day are set automatically, (RDS time synchronisation).
SETTINGS__________________________________________ Note: 7 If the device is disconnected from the mains, all saved stations will be deleted unless you have inserted back-up batteries. Time settings Setting the clock time 1 Switch the device to standby with »ON/OFF«. 2 Press and hold »MEM/TIME« until the hours flash in the display. & % & % 3 Press » TUNING « to set the hours and press »MEM/TIME« to confirm. – Display: the minutes flash.
SETTINGS__________________________________________ 3 Set the minutes with » TUNING « and confirm with »ALARM 1« or »ALARM 2«. & % Setting the brightness of the backlight display 1 Repeatedly press »DIMMER« to change the brightness of the display (3 levels) or switch of the backlight. Note: 7 In addition to this function, the ”AUTO DIMMER” ensures that the brightness of the display is adjusted to suit the brightness of the surroundings.
RADIO MODE____________________________________ General information Switching on and off Selecting preset radio stations 1 Switch on the device from standby mode with »ON/OFF«. 1 Select the radio station with »P –« or »P +«. 2 Switch on the device to standby mode with »ON/OFF«. Switching the display Adjusting the volume 1 Set the desired volume with »C« (right side of the device) 1 In radio mode, switch the display between the time/day and frequency or station name with »DISPLAY«.
RADIO MODE____________________________________ RDS time synchronisation Some RDS stations transmit an RDS time signal. If the reception is good, this time information will update the time (display: »w« flashes), as long as the time synchronisation is activated (see page 23). After successful time synchronisation, »w« remains constantly in the display. Time synchronisation can take several minutes, and even with good reception the accuracy depends on the time signal being transmitted.
ALARM MODE_ __________________________________ The device has a dynamic alarm sound, that starts with a low volume and reaches maximum volume within a short time. Viewing the alarm times 1 In standby press »DISPLAY« repeatedly. – Display: in sequence: alarm time 1, alarm time 2 and the the time and the day. Alarm with radio station 1 Press »ON/OFF« to switch on the device from standby mode. 2 Set the radio station with »P –« or »P +«. 3 Set the desired wake-up volume with »C«.
ALARM MODE_ __________________________________ Deactivating and activating alarm standby 1 To deactivate the alarm function press »ALARM 1« or »ALARM 2« repeatedly until »§ 1« or »§ 2« respectively »e 1« or »e 2« disappear from the display. – The set alarm time is saved. 2 To activate the alarm function press »ALARM 1« or »ALARM 2« repeatedly until »§ 1« or »§ 2« respectively »e 1« or »e 2« appear in the display. Deactivating/activating the alarm function for the weekend 1 In standby press »RDS/WEC«.
ALARM MODE_ __________________________________ Reminder timer The reminder timer reminds you after a certain time (between 10 and 120 minutes) with a signal tone. Activating the reminder timer 1 Press »ON/OFF« to switch the device to standby. 2 Set the desired reminder time progressively by pressing and holding down »SLEEP/NAP« or in steps by pressing the button repeatedly. – Display: »NAP«. – The device emits a signal tone to remind you after a set time. 3 End the signal tone by pressing »ON/OFF«.
INFORMATION__________________________________ Environmental note recycled. This product has been made from high-quality parts and materials which can be re-used and Therefore, do not throw the product away with normal household waste at the end of its life. Take it to a collection point for recycling electrical and electronic devices. This is indicated by this symbol on the product, in the operating manual and on the packaging. Please find out about collection points operated by your local authority.
Grundig Intermedia GmbH Beuthener Strasse 41 D–90471 Nürnberg www.grundig.