version:1.0 User Manual Blood Pressure Monitor TMB-1583-BS Arm Type Thank you for selecting a TRANSTEK Blood Pressure Monitor. Guangdong Transtek Medical Electronics Co., Ltd. Zone A, No.105 ,Dongli Road, Torch Development District, 528437 Zhongshan,Guangdong,China Please read the user manual carefully and thoroughtly to ensure the safe usage of this product,Keep the manual well for further reference in case you have problems.
CATALOGUE Table of Contents INTRODUCTION..................................................................................................................2 General Description Indications for Use Contraindications Measurement Principle Safety Information LCD Display Signal Monitor Components List BEFORE YOU START..........................................................................................................
INTRODUCTION General Description Thank you for selecting TRANSTEK arm type blood pressure monitor (TMB-1583-BS). The monitor features blood pressure measurement, pulse rate measurement and the result storage. The design provides you with two years of reliable service. INTRODUCTION Safety Information The signs below might be in the user manual, labeling or other component. They are the requirement of standard and using.
INTRODUCTION CAUTION * This device is intended for indoor, home use. * This device is not intended for public use. * This device is portable, but it is not intended for use during patient transport. * This device is not suitable for continuous monitoring during medical emergencies or operations. * This device is intended for no-invasive measuring and monitoring of arterial blood pressure.
INTRODUCTION INTRODUCTION LCD display signal Monitor Components LCD DISPLAY AIR HOSE CUFF SYMBOL DESCRIPTION High blood pressure Diastolic blood pressure Low blood pressure Pulse display Pulse in beats per minute kPa Measurement Unit of the blood pressure (1kPa=7.5mmHg) Measurement Unit of the blood pressure (1mmHg=0.133kPa) Batteries are low and need to be replaced mmHg Low battery Irregular heartbeat Blood pressure monitor is detecting an irregular heartbeat during measurement.
BEFORE YOU START BEFORE YOU START The Choice of Power Supply Setting Date, Time and Measurement Unit 1.Battery powered mode: It is important to set the clock before using your blood pressure monitor, so that a time stamp can be assigned to each record that is stored in the memory. (The setting range of the year :2018—2058 time format:24H) 6VDC 4×AAA batteries 2.AC adaptor powered mode: 6V 1A (Please only use the recommended AC adaptor model).
BEFORE YOU START 4.Repeat step 2 and 3 to set the [MONTH] and [DAY]. BEFORE YOU START Select the User 1.When the monitor is off , press and hold the MEM button to enter user setting mode. The user ID will blink. 5 .Repeat step 2 and 3 to set the [HOUR] and [MINUTE]. 2.Then press MEM button again, select the user ID between user 1 and user 2. 6.Repeat step 2 and 3 to set the [UNIT]. 7 After UNIT is set,the LCD will display “donE” first, then display all the settings you have done and then turn off.
BEFORE YOU START BEFORE YOU START Pair-up the Blood Pressure Monitor with Your Device 1.Turn on Bluetooth and the app. Make sure both are ON when pair-up is proceeding. 2 .When the monitor is OFF, press and hold the START/STOP button to start pair-up. The symbol “ + ”and user ID will be shown on the LCD alternatively, indicating pair-up is proceeding. List of compatible devices: For iOS devices: The operating system must be iOS 8 or more, such as iPhone 4S, iPhone 5/5C/5S, iPhone 6/6 Plus and so on.
MEASUREMENT MEASUREMENT Tie the cuff Start the Measurement 1. Tie the cuff on your upper arm, then position the tube off-center toward the inner side of arm in line with the little finger. Or position the artery mark over the main artery (on the inside of your arm). Note: Locate the main artery by pressing with 2 fingers approximately 2 cm above the bend of your elbow on the inside of your left arm. Identify where the pulse can be felt the strongest. This is your main artery. 1.
DATA MANAGEMENT MEASUREMENT Recall the Records 2.This device will proceed to data transmission after measurement. The Bluetooth symbol blinks on the LCD indicates data is transmitting. If the data transmission fails, the LCD will display “ ”. 1 When the monitor is off, please press the “MEM” to show the average value of the latest three records.If the records are less than three groups,it will display the latest record first.
SPECIAL FUNCTION DATA MANAGEMENT About the Lock Button Delete the Records If you did not get the correct measurement, you can delete all results by following steps below. (Take user 1 for example) 1.Hold pressing “MEM” button for 3 seconds when the monitor is in the memory recall mode ,the “User ID + dEL ALL” will flash on the display. 2.Press “SET” button to confirm deleting and the monitor will display “dEL dOnE”+User ID and then turn off.
INFORMATION FOR USER INFORMATION FOR USER Tips for Measurement Measurements may be inaccurate if taken in the following circumstances. Maintenance In order to get the best performance, please follow the instructions below.
ABOUTBLOOD BLOODPRESSURE PRESSURE ABOUT ABOUT BLOOD PRESSURE What are systolic pressure and diastolic pressure? When ventricles contract and pump blood out of the heart, the blood pressure reaches its maximum value in the cycle, which is called systolic pressure. When the ventricles relax, the blood pressure reaches its minimum value in the cycle, which is called diastolic pressure.
TROUBLESHOOTING SPECIFICATIONS This section includes a list of error messages and frequently asked questions for problems you may encounter with your blood pressure monitor. If the products not operating as you think it should, check here before arranging for servicing. PROBLEM SYMPTOM No power Low batteries Error message Warning message 24 Display will not CHECK THIS REMEDY Batteries are exhausted. Replace with new batteries Batteries are inserted incorrectly.
FCC STATEMENT AUTHORIZED COMPONENT Authorized Component 1.please use the TRANSTEK authorized adapter. Adapter Model: BLJ06L060100P-U Input:AC 100-240V 50/60Hz 0.2A Max Output:6V 1000mA Contact Information For more information about our products, please visit www.transtekcorp.com.you can get customer service, usual problems and customer download, transtek will serve you anytime. Manufactured by: Guangdong Transtek Medical Electronics Co., Ltd. Company: Guangdong Transtek Medical Electronics Co., Ltd.
EMC GUIDANCE EMC GUIDANCE EMC GUIDANCE GUIDANCE EMC Table 2 EMC Guidance The ME EQUIPMENT or ME SYSTEM is suitable for home healthcare environments. Immunity Test IEC 60601-1-2 Test level Warning: Use of this equipment adjacent to or stacked with other equipment should be avoided because it could result in improper operation. If such use is necessary, this equipment and the other equipment should be observed to verify that they are operating normally.
EMC GUIDANCE EMC GUIDANCE EMC GUIDANCE GUIDANCE EMC Table 2 EMC Guidance The ME EQUIPMENT or ME SYSTEM is suitable for home healthcare environments. Immunity Test IEC 60601-1-2 Test level Warning: Use of this equipment adjacent to or stacked with other equipment should be avoided because it could result in improper operation. If such use is necessary, this equipment and the other equipment should be observed to verify that they are operating normally.
EMC GUIDANCE Table 3 Guidance and manufacturer’s declaration - electromagnetic Immunity Radiated RF Test Band Service IEC61000-4-3 Frequency (MHz) (MHz) (Test specifications 385 380-390 TETRA for ENCLOSURE 400 PORT IMMUNITY to 450 430-470 GMRS 460, RF wireless FRS 460 communications 710 704-787 LTE Band equipment) 13, 745 17 780 810 870 930 1720 1845 1970 2450 5240 5500 800-960 GSM 800/900, TETRA 800, iDEN 820, CDMA 850, LTE Band 5 GSM 1800; 1700CDMA 1900; 1990 GSM 1900; DECT; LTE Band 1, 3, 4,25; UMTS B