Operation Manual
D
16
ENGLISH
DEGB
Battery
Protect the battery against heat and re.
Protect the battery against water and
moisture.
MAX. 40°C
Protect the battery against temperatures
above 40°C.
Li-Ion
Do not throw the batteries in household
waste.
Deliver the batteries to a collection centre of
old batteries where they will be recycled in
an environmentally friendly way.
General Power Tool Safety Warnings
WARNING
Read all safety warnings and all instructions.Failure
to follow the warningsand instructions may result in
electric shock, re and/or serious injury.
Save all warnings and instructions for future
reference.
The term „power tool“ in the warnings refers to your
mains-operated (cordepower tool orbattery-opera-
ted (cordless) power tool.
1)
Work area safety
a) Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
b) Do not operate power tools in explosive atmo
-
spheres, such as in the presence ofammable
liquids
, gases or dust. Power tools create sparks
which may ignite thedust or fumes.
c) Keep children and bystanders away while ope-
rating a power tool.Distractions cancause you to
lose c
ontrol.
2) Electrical safety
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do notuse any
adapter plugs with earthed (groundepower
tools. Unmodied plugs andmatching outlets will
reduce risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators,ranges and refri-
gerators. There is an increased risk of electric shock if
y
our body isearthed or grounded.
c) Do not expose power tools to rain or wet con-
ditions. Water entering a power toolwill increase
the r
isk of electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging thepower tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damagedor entangled cords
increase the risk of electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable foroutdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual currentdevice
(RCprotected supply. Use of an RCD reduces the
risk of electric shock.
3) Personal safety
a) Soyez attentif, faites attention à ce que vous
faites et faites preuve de bon sens lors de
l‘utilisation de l‘appareil électrique. N‘utilisez
jamais l‘appareil électrique si vous êtes fatigué,
sous eet de drogues, d‘alcool ou de médica
-
ments. A moment of inattention while operating
po
wer toolsmay result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection. Protectiveequipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protectionused for appropriate conditions
will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the o-position beforeconnecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your nger on the switch or energising power tools
that havethe switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrenchor a key left
attached to a rotating part of the power tool may
result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables bettercontrol
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothingand gloves
away from moving parts. Loose clothes, jewelle
-
ry or long hair can becaught in moving parts.
g)
If devices are provided for the connection of
dust extraction and collectionfacilities, ensure
these are connected and properly used. Use of
dust collection canreduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct po
-
wer tool for your application. Thecorrect power
t
ool will do the job better and safer at the rate for
which it was designed.
b) Do not use the power tool if the switch does not
turn it on and o. Any power toolthat cannot be
controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from thepower tool
before making any adjustments, changing
accessories, or storingpower tools. Such pre-
ventive safety measures reduce the risk of starting
the po
wertool accidentally.